E Senza Technologies SB100, SB100 E User Manual

Manual

SB110

-

NTC

E-Senza Technologies GmbH | Bücklestr. 82b | 7

8467 Konstanz | Germany

Doc V1.6

SenzaBlock

Tel.: [phone], Fax: [phone] | [e-mail] | www.e-senza.de

Leveraging Power of Wireless

®

General Information

Notice: This device complies with part 15 of the FCC Rules and with RSS-210 of Industry Canada.

Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause
undesired operation.

Notice: Changes or modifications made to this equipment not expressly approved by E-Senza
Technologies may void the FCC authorization to operate this equipment. This includes but is not
limited to modifications of the antenna or use of an antenna not approved by E-Senza Technologies.

Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Radiofrequency radiation exposure Information:

The radiated output power of the device is far below the FCC radio frequency exposure limits.
Nevertheless, the device shall be used in such a manner that the potential for human contact during
normal operation is minimized.

This is the safety alert symbol. It is used to alert you to potential personal injury

This symbol and the accompanying text alerts the reader to a situation which may

Leveraging Power of Wireless

®

Safety Information

In order to ensure the safe use of the product described, you have to read and understand this
manual. The following notes provide information on how to use this manual.

Explanation of symbols used and signal words

The following types of messages provide information about possible property damage and general
information concerning proper operation and ease-of-use.

hazards. Obey all safety messages that follow this symbol to avoid possible injury
or death.

The following types of messages provide information about possible property damage and general
information concerning proper operation and ease-of-use.

SenzaBlock is ESD sensitive !

• Prevent SenzaBlock OEM module or PCB inside the enclosure from touching your clothing.
Most clothing is insulative and retains a charge even when you are wearing a wrist strap.

• Wear a grounded wrist strap against your skin to eliminate static on your body

• Hold SenzaBlock by its enclosure or its edge. If you are removing a pluggable module, use

the correct tool.

cause damage or malfunction to the device, either hardware or software, or
surrounding property.

This symbol and the accompanying text provide additional information to the
reader. It is also used as a reference to other sources of information (manuals,
data sheets) on the subject matter, product, etc.

User group of this manual

The use of products described in this manual is oriented exclusively to

– qualified electricians or persons instructed by them, who are familiar with applicable

standards and other regulations regarding electrical engineering and, in particular, the
relevant safety concepts.

– qualified application programmers and software engineers, who are familiar with the safety

concepts of automation technology and applicable standards.

E-Senza Technologies accepts no liability for erroneous handling or damage to products from E­Senza Technologies or third-party products resulting from disregard of information contained in this
manual.

Battery Handling Guidelines

• Insert the battery correctly (+/-).

• Do not recharge

• Do not open or dispose in fire

• Do not heat above 100°C

• Do not expose contents to water

• Do not mix with used batteries or other battery types

Not considering the above steps may lead to explosion, leaking of battery and can cause damage!

Leveraging Power of Wireless

Content

1 SenzaNET ................................................................................... 1

1.1 Communication in SenzaNET ...................................................... 1

1.2 Network Elements ................................................................... 2

1.2.1 SenzaBlock ............................................................................................. 2

1.2.2 Gateway ................................................................................................ 2

1.2.3 SenzaWMS .............................................................................................. 2

2 SenzaBlock SB110-NTC .................................................................... 2

2.1 Features .............................................................................. 2

2.2 Installation ........................................................................... 2

2.2.1 Mechanical Installation............................................................................... 2

2.2.1.1 Sensor Temperature Grade ..................................................................... 3

®

2.2.2 Electrical Installation................................................................................. 4

2.2.2.1 Connecting Sensor and Power-supply ......................................................... 4

2.2.2.2 Antenna Connection ............................................................................. 4

2.2.2.3 Software Configuration .......................................................................... 6

3 Troubleshooting ............................................................................ 7

4 Technical Support and Training ......................................................... 8

5 Warranty .................................................................................... 8

6 Environmental Compliance ............................................................... 8

7 CE conformity .............................................................................. 9

Copying of this document in full or in part, and giving it to others and the use or communication

of the contents there of, are forbidden without express authority. Offenders are liable to the

payment of damages. All rights reserved for E-Senza Technologies GmbH, Konstanz, Germany in the

event of the grant of a patent or the registration of a utility model or design. (DIN 34-1-E)