Page 1
2.4G RF Dim & CCT Selectable LED Panel (Can be set
lights as standard lighting with default 4000K)
2.4G RF Dim & CCT Selectable LED Panel (Can be set
lights as standard lighting with default 4000K)
2.4G RF Dim & CCT Selectable LED Panel (Can be set
lights as standard lighting with default 4000K)
Recessed Mount
Ceiling
Ceiling Ceiling
1. Ensure the panel light work well before installation, put the panel light at a diagonal position.
2. Put the driver aside and insert panel light into ceiling.
3. Rotate the panel light 45° in horizontal direction to make the front of panel face to ceiling square hole.
4. Rotate the panel light 90° in vertical direction to make it correspond to the recessed frame and
front of panel face to ground.
5.
Embed the panel light into ceiling, adjust it to a suitable position to make it as flat as ceiling.
Ceiling
CeilingCeiling
Suspension Mount
x 2
x 2
x 2
600-1000mm
400-1000mm
1. Make sure that the ceiling can hold the weight of the LED panel and install ceiling brackets
suitable to support the weight of the LED panel.Fixing cables.
2. Gather panel and connect the wires as shown in”Assembling panel”
3. Attach the suspended cables to the bends at the edges of the LED flat panel.
4. Turn on the main power. installation is finished.
We appreciate your business!
How'd we do?
Please take a moment to let us know. We will provide a FREE wall mount
remote controller (mode # EEFPTL-RC-W) if you can register on our
website: www.eleding.com and leave us your positive feedback at Home
Depot.com. Please contact us via sales@eesgi.com to get the FREE
remote!
Surface Mount
1. Parts A1,A2, B1,B2;
2. First install A1, A2, and B1(as illustrated);
3. As is shown in the figure,fix A1 and A2 on the ceiling or on the roof,and then insert the panel light directly
(the end with power source enters later);
4. Install B2, finish installation.
L out
EE Systems Group Inc. www.eleding.com , info@eesgi.com. 1-877-579-3889 (M-F, 10am-5pm PST), v062019
We use your feedback to improve our operations for you and customers
like you.
Thanks!
EE Systems Group Inc. www.eleding.com , info@eesgi.com. 1-877-579-3889 (M-F, 10am-5pm PST), v062019
EE Systems Group Inc. www.eleding.com , info@eesgi.com. 1-877-579-3889 (M-F, 10am-5pm PST), v062019
Page 2
2.4G Wireless Dimming & CCT Tunable LED Panel
2.4G Wireless Dimming & CCT Tunable Remote Controller
2.4G Wireless Dimming & CCT Tunable Remote Controller
Product description
Product Introduction
The ultra slim panels illuminate over their complete surface brightly and highly homogeneous in white or warm white
(according to version). They are out-standingly suited for coffered ceilings but can also be used as elegant interior
design elements directly on walls or ceilings. The panel will not produce too much heat and no need to cooling.
The homogeneously illuminated surface almost has no glare and has highly modern appearance. The use
of efficient, long-life and high quality
Product Features
Long life
Its service life is significantly longer than fluorescent lamps or other light sources.
Ecological
Saves electricity and low carbon.
Saves energy
Consumes less energy via use of efficient LEDs.
Homogeneous
Very uniform light distribution
Elegant
Modern ultra thin design, healthy light, no UV component and almost no glare.
Applications
The most common places you are likely to find the panel lights include：hospitals, schools, hallways, lobbies,
meeting rooms, restaurants, offices and etc.
LEDs means that you save electricity and ready cash.
in the complete surface.
Attention
a. Handheld remote and Wall-type remote controller cannot be
used directly as a switch, they should be used together with
the switch.
b. Not allow to use scouring powder, abrasive powder, oil and acid alkaline type
detergent.
c. Do not spray air fresheners, disinfectant, cleaning organic solvents directly on
light-emitting surface.
d. Wire connectors can not contact with water.
e. Do not let sharp objects to scratch the lamp,especially the light-emitting surface.
THE HANDHELD REMOTE CONTROLLER
Turn on
Remote controller provides users most flexibility adjustment for smoothly dimming
and selecting color temp, the standard wall mount hardwired switch is highly
recommended as primary ON-OFF control for normal operation in most case
Once select satisfied setting by remote control, it will be saved with ON-OFF
COLOR(CCT)
5000K 4000K 3500K 3000K
BRIGHTNESS
in remote control use until next setting change
Initial matching the code between light(s) and remote to activate
operate by the remote controller
Turn the wall hardwired switch/circuit breaker OFF, press and hold the ID
button until a tiny RED LED indicator is flashing on top of the remote then
turn ON the wall hardwired switch/circuit breaker, and release the ID button
after panel light(s) flashing
Erase the existing code for resetting up
Turn the wall hardwired switch/circuit breaker OFF, then press and hold the
+
button together for couple seconds, following turn the wall
hardwired switch/circuit breaker ON, release the buttons after panel light(s)
flashing
+
Group lights Setting up
After Initial matching the code between light(s) and remote, this handheld
remote allow to use up to four groups (1; 2; 3; 4) in selecting use: Turn the
grouping wall hardwired switch/circuit breaker OFF, following press the group
selection button for few seconds, then turn ON this group of lights, release
the group button after group lights flashing. Do the same for other groups.
Save pre-set brightness level and color temp
Save
GROUPING
Press and hold the SAVE button for few seconds until the lights shut OFF with
your pre-set brightness and color temp, then settings are saved. Now wall hardwired
switch works as normal function with pre-selected lighting profile, also applicable for
group setting
All Groups are selected
5000K
4000K
25% brightness
50% brightness
Increase brightness Decrease color temperature
Power the light off then power it on, the last saved brightness (which is saved by the button "SAVE")
and the last saved color temperature (which is saved by the button "SAVE" or "OFF") will be displayed
by default. The defaulted factory setting of the light is 100% brightness and 4000K.
Turn off
3500K
3000K
75% brightness
100% brightness
Increase color temperatureDecrease brightness
THE WALL TYPE REMOTE CONTROLLER
Turn on Turn off
It has much flexibility for selecting dimming & color temp change. Can fit in a 1-gang box as
wall switch for small individual/partition area or lighting cover area w/o hardwired switch &
standard dimmer but circuit breaker is recommended if available for the setting up
Dual functions:
1. Momentary press to ON the light as normal;
2. Press and hold few seconds until lights shut OFF to SAVE the pre-setting profile for operating
Momentary press it to shut OFF the light
Initial code learning between light and remote to activate the unit
Turn the wall hardwired switch/circuit breaker OFF, press-hold ON & OFF buttons together till
RED LED flashing on top of the remote; turn ON the wall switch/circuit breaker, release buttons
+
A
A
The matching method of hand-hold remote controller and wall-type remote controller, the wall
controller can copy some of the functions of the hand-hold controller by the following method.
NO Grouping Hand-hold controller Wall-type controller
1
2
3
4
5
After 10s of each operation the controller will enter standby power saving mode. If you need to make adjustments, simply
press the "ON" button, the indicator will flash to show it is working. (If the controller is under working mode, the indicator
will flash no matter which button is pressed).
Power the light off then power it on, the last saved brightness (which is saved by the button "ON") and the last saved color
temperature (which is saved by the button "ON" or "OFF") will be displayed by default. The defaulted factory setting of the
light is 100% brightness and 4000K.
after panel light(s) flashing
If you need to use both hand-hold controller and wall controller for the
same light, please don't use this function, directly use the following copy
function.
Built on RF remote dimmer (w/o any additional wirings & dimmer)
Keep momentary pressing this button to select color temps between 3000K to 5000K in
cycle
ON+CCT
ON+CCT
ON+CCT
ON+CCT
ON+CCT
AL L
1
2
3
4
1+ID
2+ID
3+ID
4+ID
ID
EE Systems Group Inc. www.eleding.com , info@eesgi.com. 1-877-579-3889 (M-F, 10am-5pm PST), v062019
EE Systems Group Inc. www.eleding.com , info@eesgi.com. 1-877-579-3889 (M-F, 10am-5pm PST), v062019
EE Systems Group Inc. www.eleding.com , info@eesgi.com. 1-877-579-3889 (M-F, 10am-5pm PST), v062019
Loading...