Escalade sports T8512 User Manual
MODEL NOS.
T8512T8512
T8512
T8512T8512
TOURNAMENT
SERIES 3
TABLE TENNIS TABLE
OWNER'S MANUAL
1. Read this manual carefully before starting assembly. Read each step completely before beginning
each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons
before assembling or ordering parts.
3. To make assembly easier, use the Hardware Identifier on page 8 to identify and sort all
fasteners. Check all cartons for kits. All hardware may not be located in one kit.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes
may not align and parts may not easily fit together. Leave locknuts slightly loose until you are instructed to
tighten them.
5. Tools required for assembly: Phillips screwdriver, tape measure, two 7/16” wrenches and two 9/16”
wrenches (adjustable wrenchs may be substituted for the wrenches).
Please Do Not Return This Product To The Store!
Contact Escalade® Sports customer service department at:
Phone: 1-866-873-3528 Toll – Free !
Fax: 1-866-873-3533 Toll – Free !
E-mail: tabletennis@escaladesports.com
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Please visit our World Wide Web site at: www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
®
ADDITIONAL ESCALADE
SPORTS PRODUCT INFORMATION
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
2L-6820-00
1. ATTACHING LEGS TO TABLE TOPS
CAUTION
AT LEAST TWO ADULTS ARE NEEDED TO COMPLETE
THE FOLLOWING STEPS!
1. Leave top halves #1 in shipping carton as shown
above or lay them on a carpeted floor (to protect
them from damage and scratches ).
2. Attach leg assembly #10 to brackets #6 located
on the bottom of the first top half #1. (See above).
Use bolts #27, spacers #20 and locknuts #28.
(See Detail A).
NOTE: Be sure brace on leg assembly #10 is
against table. (See Detail B).
Tighten these locknuts snug but DO NOT
OVERTIGHTEN THEM. JOINT MUST MOVE!
3. Put caps #21 on bottom end of leg assembly
#10. (See Detail C).
4. Attach upright assembly #11 to remaining brackets
#6 on the bottom of the first top half #1. (See
above). Use bolts #26, spacers #20, and locknuts
#28. (See Detail D). Tighten locknuts snug but
DO NOT OVERTIGHTEN THEM. JOINT MUST
MOVE!
5. With a helper, set the first top half #1 on its side
against a wall. (Be sure to put a piece of cardboard,
cloth, or carpeting on the floor first to protect the
top's edges. ) Turn the second top half #1 over
and repeat steps 2-4 to assemble it.
2
2. ATTACHING NAME PANELS TO LEGS
AT LEAST TWO ADULTS ARE NEEDED TO COMPLETE THE FOLLOWING
CAUTION
STEPS! DO NOT LEAVE TABLE UNATTENDED UNTIL ASSEMBLY IS
COMPLETE!
6. With a helper, hold top halves about 14 ½
inches apart. Attach only one half of name
panels #8 to upright assemblies #11 as shown
above. Use ONLY TWO bolts #26 and locknuts
#28 on each name panel.
(Two other bolts #27 and nuts #28 will be used in
the next section to attach the other half of the name
panels and linkages #24 at the same time. See next
page. ) Do not tighten these locknuts completely
tight yet.
HELPFUL HINT: Start at the bottom and insert two
bolts #26 UPWARD through upright assemblies
#11 and name panel #8. Then attach the upper
name panel #8. Insert bolts #26 DOWNWARD.
7. Attach safety latches #9 to name panels using one
screw #29, flat washer #30 and locknut #31.
(See Detail E). Attach a safety latch to one
name panel to hold one table half and the
other safety latch to the other name panel to
hold the other table half.
3
Loading...