
MODEL NOS.
T8510T8510
T8510
T8510T8510
ADVANTAGE
QUICK SERVE 1
TABLE TENNIS TABLE
OWNER'S MANUAL
1. Read this manual carefully before starting assembly. Read each step completely before beginning
each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons
before assembling or ordering parts.
3. To make assembly easier, use the Hardware Identifier on page 5 to identify and sort all
fasteners. Check all cartons for kits. All hardware may not be located in one kit.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes
may not align and parts may not easily fit together. Leave locknuts slightly loose until you are instructed to
tighten them.
5. Tools required for assembly: Phillips screwdriver, 3/8” wrench and two 7/16” wrenches (adjustable
wrenchs may be substituted for the wrenches).
Please Do Not Return This Product To The Store!
Contact Escalade® Sports customer service department at:
Phone: 1-866-873-3528 Toll – Free !
Fax: 1-866-873-3533 Toll – Free !
E-mail: tabletennis@escaladesports.com
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Please visit our World Wide Web site at: www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
®
ADDITIONAL ESCALADE
SPORTS PRODUCT INFORMATION
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
2L-6818-00

1. Gently tap a caster socket #12 into each Upright Tube #21 until
flange on sockets touches the edge of the tube. DO NOT HIT
CASTER SOCKET TOO HARD WITH A HAMMER! Sockets
may break if hit too hard.
2. Insert casters #11 into caster sockets #12.
Figure 2
4. Connect the two Name Plate Assemblies to the
Bottom Board #28, as shown in Figure 3, using
four bolts #35 and four nuts #15.
Figure 1
3. Attach two Upright Tube Assemblies to both Name Plates #5, as
shown in Figure 2, using four bolts #9 and four nuts #15.
Figure 3
5. Install a safety latch #8 into the right-hand hole
on each name panel as shown in Figure 3. Use
one screw #10 one washer #17 and one hex nut
#16. NOTE: Flange on safety latch must
extend over top of name panel as shown in
Figure 3. Safety latch must pivot freely.
INSTALL SAFETY LATCHES #8 AS SHOWN ABOVE FOR PROPER USE OF
CAUTION:
6. Rotate U-support #7 until you see the screw holes in the slots
of the three U-clips #6. Slide U-support #7 side to side if necessary. See Figure 4.
7. Rotate U-leg #2 until you see the screw hole in the slot of center U-clip #3. Slide U-leg #2 side to side if necessary. See Figure 4.
8. Insert screw #19 through slot in U-clip #6 and into U-support
#7. Thread it all the way into U-support #7 until it touches the
back of the tube. There should be about 3/8 inch of screw
#19 left sticking out.
TABLE! DO NOT SKIP THIS STEP! DO NOT OPERATE TABLE UNTIL SAFETY
LATCHES ARE INSTALLED AND ASSEMBLY IS COMPLETE!
Figure 4
9. Insert screw #34 through slot in U-clip #3 and into U-leg #2.
Thread it all the way into U-leg #2 until it touches the back of
the tube. There should be about 3/8 inch of screw #34 left
sticking out.
2

10. Lay table top #1 painted side down, on a smooth, flat surface. Use
the shipping container to protect the painted surface of the table
top.
11. Attach end of linkages #4 with two holes to INSIDE of U-leg #2 as
shown in Figure 5. Secure with bolts #14, locknuts #15 and plastic spacers #32. Tighten hardware snug enough to keep table stable
but do not overtighten. Tubes must pivot freely. NOTE: Plastic spacers go between linkages #4 and U-leg #2.
12. Attach other end of linkages #4 to OUTSIDE of U-support #7
with bolts #33, locknuts #15 and plastic washers #24. Tighten
hardware until snug but do not overtighten. Tubes must pivot freely.
13. Instal leg cap #13 onto end of U-legs #2.
14. On one side of the table attach slotted end of safety strap #30 to
INSIDE of U-Leg #2 using one bolt #33, one spacer #31, one
washer #24, and one hex nut #15. Tighten hardware until snug
but do not overtighten. Tubes must pivot freely. See Figure 6.
Figure 5
Figure 6
Figure 7
17. Prepare an area for the assembly of the second table top half. If
necessary, move the first table top half aside with the aid of a helper.
Be sure to place it in a location where it won't be disturbed or damaged. If setting on its side, be sure to place the bottom edge no less
than 12 inches away form the wall. Also be sure to place carpet or
pieces of the shipping carton down to protect table top edges. If
floor is not carpeted, brace table top half with a heavy object to
keep it from sliding.
18. Repeat steps 6 thru 16 on second table half.
AT LEAST TWO (2) ADULTS ARE NEEDED TO COMPLETE
THE REST OF THIS ASSEMBLY! WHEN ASSEMBLING TOPS
TO BASE, HANDLE TOP ASSEMBLIES BY GRASPING ONLY
THE TOPS THEMSELVES. DO NOT GRASP METAL LEGS,
U-SUPPORT, LINKAGE, OR HINGES. THESE PARTS CAN
MOVE AND COULD PINCH FINGERS OR HANDS
CAUSING SERIOUS INJURY! ASSEMBLE AS SHOWN WITH
LEGS FULLY CLOSED AND TOPS IN A VERTICAL
POSITION. DO NOT OPEN LEGS AND TRY TO ASSEMBLE.
TABLE TOPS ARE HEAVY - DO NOT ATTEMPT TO
ASSEMBLE ALONE!
15. Attach other end of safety strap #30 to OUTSIDE of linkage #4
using one bolt #9, one washer #24, one spacer #31, and one
hex nut #15.
Important! Do NOT put other saftey strap #6 on this table half.
It will be installed on other table half later.
16. Attach two Corner Caps #22 to bottom of table, as shown in
Figure 7, using three screws #23 per Corner Cap.
Figure 8
19. With two adults, attach table top (#1) to table base, as shown in
Figure 8. With at least one adult on each side of table top, lift top
and align ends of "U"-support tube with top of upright tubes. Slide
tubes together.
20. With two adults, put other table top onto other pivot tubes following
instructions in previous step.
DO NOT OPEN THE TABLE TO PLAYING POSITION
UNTIL BOTH TOPS ARE INSTALLED! DO NOT LEAVE
TABLE STANDING UNATTENDED. IT COULD BE
KNOCKED OVER CAUSING SERIOUS BODILY INJURY
OR PROPERTY DAMAGE.
3