Escalade sports T8413F User Manual

MODEL NO.

527.26290527.26290

527.26290

527.26290527.26290
T8413FT8413F

T8413F

T8413FT8413F

TABLE TENNIS TABLE

OWNER'S MANUAL

1. Read this manual carefully before starting assembly. Read each step completely before beginning

each step.

2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons
before assembling or ordering parts.

3. To make assembly easier, use the Hardware Identifier on page 10 to identify and sort all
fasteners. Check all cartons for kits. All hardware may not be located in one kit.

4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes

may not align and parts may not easily fit together. Leave locknuts slightly loose until you are instructed to
tighten them.

5. Tools required for assembly: Phillips Screwdriver, Two 7/16 Wrenches, One 3/8 Wrench (an adjustable

wrench may be substituted for the wrenches).

Please Do Not Return This Product To The Store!

Contact Escalade® Sports customer service department at:
Phone: [phone] Toll – Free !
Fax: [phone] Toll – Free !
E-mail: [e-mail]
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706

Please visit our World Wide Web site at: www.escaladesports.com

ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE

ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS

®

ADDITIONAL ESCALADE

SPORTS PRODUCT INFORMATION

2L-7074-00

Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.



2006 Escalade









Sports

20

20

20

23

23

23

1A

1B

3

3

3

3

3

3

20

20

20

20

20

20

ThisEndistheMiddle
ofthetable

7(U-Support)

2(U-Leg)

Slotin
U-Clip

1. Lay table top sections #1A & 1B (striped side down

13

13

7(U-Support)

2(U-Leg)

StripeOnEnd

and holes for metal support plates #23 aligned) on a
smooth flat surface as shown in Figure 1. Note: If

the surface you are working on is not carpeted,
you can use shipping container to protect the
surface of the table top.

DO NOT PUT YOUR ENTIRE WEIGHT ON TABLE
TOP BOARDS WHEN ASSEMBLING TOP. YOU
COULD DAMAGE TOPS.

2. Butt the two table top sections together and attach three
metal support plates #23 to table top using six screws
#20 in each plate as shown in Figure 1.

Figure 1

Figure 2

5. Align the holes in the U-clips #3 with pilot holes in
table top assembly and secure with twenty four screws
#20 as shown.

3. Assemble the two “L” tubes and the center tubes that
make up the “U” Support and the “U” Leg. Align on
Table Top as shown in Figure 2. Note: “U” Leg is

larger and wider than the U Support. The U­leg should be installed on the end of the table
half with the end stripe on top side

4. Put plastic caps #13 on the end of U-leg #2.

Be sure the slot in the six U-clips #3 all face theBe sure the slot in the six U-clips #3 all face the

Be sure the slot in the six U-clips #3 all face the

Be sure the slot in the six U-clips #3 all face theBe sure the slot in the six U-clips #3 all face the
same direction (toward the middle of the tablesame direction (toward the middle of the table

same direction (toward the middle of the table

same direction (toward the middle of the tablesame direction (toward the middle of the table
with the U-support) as shown.with the U-support) as shown.

with the U-support) as shown.

with the U-support) as shown.with the U-support) as shown.

IMPORTANT:

Figure 3

IMPORTANT: U-Leg is wider than U-support.
Make sure they are assembled exactly as
shown. If not, there will be a large gap between
table halves and table will not operate properly!

2

6. Rotate U-support #7 until you see the screw hole in

19

19

3

3

7(U-Support)

2(U-Leg)

NOTE:Slidetubesback
andforthuntilyousee
theholeifnecessary.

14

6

21

16

14

4

21

16

2

Righthand

hingehas“R”

stampedonit.

Lefthand

hingehas“L”

stampedonit.

14

4

21

16

14

6

21

16

the slot of U-clip # 3. Slide U-support #7 side to side
if necessary.

7. Insert screw #19 through slot in U-clip #3 and into
U-support #7. Thread it all the way into U-support
#7 until it touches the back of the tube. There should
be about 3/8 inch of screw #19 left sticking out. Re­peat for U Leg #2.

Figure 4

8. Attach hinge and brackets #6 and #4 to U-leg #2 as
shown in Figure 4. NOTE: Hinges are right hand

and left hand and must be attached as shown.

Left hand hinge #6 has the letter “L” stamped on it and
the right hand hinge has “R”. Attach with screws #14,
plastic washers #21 and locknuts #16. Tighten nuts
until snug, but do not overtighten. Hinges must pivot.
See Figure 5.

Figure 5

3

9. Screw left hand hinge brackets #6 to table top follow-

7

5

5

2

15

9

9

First
Table Half

9

9

6

BracketandLeg
flatagainsttable

Hinge

U-Leg

2

20

2

Spacerbetween
hingelegs

U-Leg

Hinge

Pull To

LockHinge

ing these steps:
A. Push U-leg #2 and hinge assembly flat against

top. See Figure 6.

B. Place a spacer that is about 1/16” thick between

hinge legs. Suggestion: either a nickel or a quarter
is an ideal spacer. See Figure 7.

C. With hinge bracket, hinge and leg flat against table

top and spacer between hinge legs, screw bracket
to table with five #20 screws. See Figure 7.

D. Open leg and lock leg hinge. See Figure 8. Re-

move spacer that you used between hinge legs.

10. Repeat step 9 to attach right hand hinge bracket to

table.

Figure 8

Figure 6

Figure 7

11. Attach name panel #5 to inside of U-supports #7.

Secure with hex bolts #9 and locknuts #15. Tighten
nuts but be careful not to crush tubes. See Figure 9.

Figure 9

4