Escalade sports T8358 User Manual

OWNER'S MANUAL

MODEL NOs.

T8358

T ABLE TENNIS TABLE

Questions, Concerns, Comments?

Need to Purchase Replacement Parts?

Need Product Assistance?

Escalade Sports, a diversified manufacturer of fine sporting goods equipment, is here to help you in any way
possible to make your experience with this product a pleasurable one for you and your family. W e always try
hard to make sure that our products are manufactured free from defects in material and workmanship to
provide a lifetime of family fun. If you find any problems with your new product such as missing parts,

damaged parts, or incorrectly manufactured parts,

Please Do Not Return This Product to the S tore!

Please contact our consumer affairs department at:

Phone [phone] Toll – Free !
Fax [phone] Toll – Free !
E-mail [e-mail]

WARRANTY

Actual product may

differ slightly from that

shown in illustrations.

READ ASSEMBLY &

OPERATING INSTRUCTIONS

AND ALL SAFETY

INFORMATION CAREFULLY!

Additionally , we highly recommend that you visit our web site for additional
information or possible solutions for your concern which include:

On-Line T rouble Shooting *** On-Line Parts

Requests *** Technical Assistance *** Frequently

Asked Questions *** Additional Escalade

Product Information

Mailing Address: Escalade Sports

PO Box 889

Evansville, IN 47706

CA UTION

THIS IS A GAME TABLE. DO NOT SIT, STAND, LEAN, WALK OR JUMP ON TABLE! FAILURE TO COMPLY
WITH THIS CAUTION COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!

This table must be kept indoors to prevent damage to the playing surface. Dampness and extreme
temperature changes which occur on patios, garages or similar areas can cause wood to warp, swell,
crack, or blister.

UNLEVEL FLOORS

If table does not seem level, it is probably because floor is not level. Move table several inches (set table
in playing position) in different directions to find the best location for the table. If the floor is extremely
unlevel, table may not play or operate properly. If table is high in the center, shim up under the outer
legs.

Escalade® Sports products may be manufactured and/or licensed under the following patents. Additional patents may be pending.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
One or more of the listed patents and/or pending patents may cover specific product.

© 2002 Escalade Sports

2L-4106-01

For aid in identifying hardware, see hardware identifier on page 9.

Figure 1

1. Lay table top #1 painted side down, on a smooth, flat
surface. Use the shipping container to protect the
painted surface of the table top.

2. Assemble the two “L” tubes and the center tubes that
make up the “U” Support and the “U” Leg. Align on
Table Top as shown in Figure 1. Note: “U” Leg is

larger and wider than the U Support. The U-leg
should be installed on the end of the table half
with the end rail mounting holes.

3. Put plastic caps #13 on the end of U-leg #2.

4. Align the holes in the U-clips #3 with pilot holes in table top
assembly and secure with twenty four screws #20 as shown.

IMPORTANT:

Be sure the slot in the six U-clips #3 all face the
same direction (toward the end of the table with the
U-support) as shown.

Figure 2

IMPORTANT: U-Leg is wider than U-support.
Make sure they are assembled exactly as
shown. If not, there will be a large gap
between table halves and table will not
operate properly!

2

5. Lay out rails #25 and 26, as shown in Figure 3, around edges

of table top.

6. Line up holes in rails with pilot holes in top and secure using

eighteen screws #20. See Figure 3.

Figure 3

7. Lay Corner Caps #22 on table as shown in Figure 4. If Corner

Cap sticks above table top surface of table, flip over so shorter
distance is against edge. Secure to bottom of table with three
screws #21.

8. Rotate U-support #7 until you see the screw hole in

the slot of U-clip # 3. Slide U-support #7 side to side
if necessary .

9. Insert screw #19 through slot in U-clip #3 and into

U-support #7. Thread it all the way into U-support
#7 until it touches the back of the tube. There should
be about 3/8 inch of screw #19 left sticking out. Re­peat for U Leg #2.

Figure 4

Figure 5

3