Escalade sports T8294 User Manual
MODEL NO.
T8294T8294
T8294
T8294T8294
TABLE TENNIS TABLE
OWNER'S MANUAL
1. Read this manual carefully before starting assembly. Read each step completely before beginning
each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons
before assembling or ordering parts.
3. To make assembly easier, use the Hardware Identifier on page 7 to identify and sort all
fasteners. Check all cartons for kits. All hardware may not be located in one kit.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes
may not align and parts may not easily fit together. Leave locknuts slightly loose until you are instructed to
tighten them.
5. Tools required for assembly: Phillips Screwdriver, Two 7/16 Wrenches, One 3/8 Wrench (an adjustable
wrench may be substituted for the wrenches), Flat Blade Screw Driver
Please Do Not Return This Product To The Store!
Contact Escalade® Sports customer service department at:
Phone: 1-866-873-3528 Toll – Free !
Fax: 1-866-873-3533 Toll – Free !
E-mail: tabletennis@escaladesports.com
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Please visit our World Wide Web site at: www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE® SPORTS PRODUCT INFORMATION
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
2L-7068-00
2006Escalade
Sports
AT LEAST TWO ADULTS ARE NEEDED TO COMPLETE THE ASSEMBLY!
CAUTION:
CAUTION:
DO NOT LEAVE TABLE UNATTENDED UNTIL ASSEMBLY IS
COMPLETE!
1. Open the hardware kit and sort all the hardware. For your help
in identifying hardware, see the hardware identifier on page 7.
2. Insert one Caster without Brake #11 and one Caster with Brake
#12 into Caster Beam #14. Be sure casters are inserted all the
way into caster beam. Assemble both caster beams and casters
the same way. See Figure 1.
3. Attach two Upright Tubes #15 to each Caster Beam #14 using
two Carriage Bolts #28, two washers #29 and two locknuts
#26 in each tube. See Figure 2. Tighten nuts but do not
overtighten, cracking the plastic.
4. Attach one Safety Latch #19 in the right hand hole of a Name
Panel #17 as shown in Figures 3 and 3A. Attach with one screw
#24, one washer #25 and one locknut #23. NOTE: Safety
latch must be installed exactly as shown, with flange
on safety latch over top of name panel.
IMPORTANT: Do not overtighten locknuts. Latches #19 must
pivot freely. When latch is pivoted, it must freely fall back
to original position when released.
Assemble the other safety latch #19 to the other name
panel #17 in exactly the same way.
INSTALL SAFETY LATCHES EXACTLY AS
SHOWN. DO NOT SKIP THIS STEP. DO NOT
OPERATE TABLE WITHOUT SAFETY LATCHES
INSTALLED.
Figure 1
Figure 2
Figure 3
Figure 3A
2
CAUTION:
5. Attach Name Panel #17 to inside of Upright Tubes #15 using
two bolts #21, two bolts #22, and four locknuts #26. See
Figure 4. Short bolts #22 go in top holes and long bolts #21 go
in bottom holes. Tighten top bolts #22 but do not overtighten,
crushing tubes. Do not tighten bottom bolts #21 tight yet,
they will have to be removed in a later step.
6. Repeat step 5 with other name panel and caster beam with upright
tubes. See Figure 4.
7. Attach Wood Bottom Board #18 to Caster Beams #14 as shown
in Figure 5. Attach with four bolts #32 and four locknuts #26.
Tighten locknuts #26 but do not overtighten, cracking plastic.
See Figure 5.
Figure 4
AT LEAST TWO ADULTS ARE NEEDED TO
COMPLETE THE REMAINDER OF THIS
ASSEMBLY!
Figure 5
3
Loading...