Escalade sports T8291 User Manual

OWNER'S
MANUAL

For Model No.

T8291

When ordering repair
parts, always give the
following:

! Part Name
! Part Number
! Model Number
! Part Description

CAUTION

READ THESE

INSTRUCTIONS

CAREFULLY!

Table Tennis Table

Thank you for buying our product. We try hard to ensure that our products are of high quality and
free of problems, such as manufacturing defects or missing parts. However, if you have any
problems with your new product, please DO NOT RETURN IT TO THE STORE!.

DO NOT RETURN THIS PRODUCT TO THE STORE!

Call us at:

TOLL FREE 1-800-426-1421

(THIS IS A CONSUMER ONLY NUMBER)

Please have this Owner’s Manual with you when you call.

Or write us at: CUSTOMER SERVICE DEPT., P.O. Box 889, Evansville, IN 47706

Fax Number: [phone].

Please provide model number and/or part number (not just the key number) of the product and/or part when
you call or write. These numbers can be found on the product, packaging, and/or in this Owner’s Manual.

LIMITED 1 YEAR WARRANTY

Manufacturer warrants to the original retail purchaser, this product to be free from defects in
material and workmanship for a period of one (1) year from the date of purchase. Should this
product become defective due to material or workmanship within the warranty period, contact our
Customer Service Department. If defective by the terms of this warranty, we will, at our option,
repair or replace the product. This warranty is not transferable and does not cover normal wear
and tear, or damage caused by improper handling, installation or use of this product. This warranty
is also void if product is in any way abused, damaged, or modified from its original state, or if used
for other than residential use. This warranty gives you specific legal rights, and you may have other
rights which vary from state to state.

2L-6548-00

TOOLS NEEDED FOR ASSEMBLY

CAUTION

Tools Needed:! 3/8 Open or Boxed End Wrench (2) ! Rachet (optional)

! 7/16 Open or Boxed End Wrench (2) ! 3/8 Socket (If using rachet)
! 1/2 Open or Boxed End Wrench (2) ! 9/16 Open or Boxed End Wrench (2)
! Phillips Screwdriver ! 9/16 Socket (If using rachet)
! Standard Screwdriver

AT LEAST TWO ADULTS ARE NEEDED TO COMPLETE THE ASSEMBLY!
DO NOT LEAVE TABLE UNATTENDED UNTIL ASSEMBLY IS COMPLETE!

FRAME ASSEMBLY

1. Open the hardware kit and sort all the hardware.
For your help in identifying hardware, see the
hardware identifier on the front of this manual.

2. Attach two non-locking casters #3 and two
locking casters #4 to frame base #1. NOTE:

Dimples in frame base should face up.
(See figure 1) Locking casters #4 must be
on opposite corners from each other.

Secure casters using washers #6 and jam
nuts #5. Tighten nuts but do not over

tighten crushing tubes.

FIGURE 1

3. Put tube end caps #29 in the ends of the base
frame tubes #1. (See figure 1)

4. Attach "U" uprights #8 to base frame #1, with
dimples facing inward, using three bolts #9,
six washers #10 and three locknuts #11. (See
figure 1) Do not over tighten bolts crushing

tubes.
Note: One washer goes on top of "U"

uprights, and one goes under the base
frame. (See figure 1)

5. Attach name plate #14 to inside of "U" uprights

#8 using two bolts #12 and two locknuts #13.

Tighten these nuts securely BUT do not
over tighten them crushing tubes.

FIGURE 2

2

ATTACHING SAFETY LATCHES

6. Install the Safety Latches #18 to the
Name Plates #14 using two screws
#35, safety latch #18, washer #15 and
locknut #20. Safety Latches must

be installed opposite each other
on both sides of the assembly.

(See figure 3)

Do not over tighten nuts #20.
Safety latch #18 must be free to
pivot.

IMPORTANT: SAFETY LATCHES
MUST BE INSTALLED AS SHOWN
WITH FLANGE ON LATCH OVER
TOP OF NAME PLATE.

FIGURE 3

7. You may want to place a towel
between table top and wall to keep
from scratching wall. Take either

table half #32 and lean it up against a
wall. Turn it so that the two legs with
hinges are up farthest from the floor.
Place the bottom of the table about 12
inches away from the wall. (See
figure 4)

Note: If you desire, table can be placed
on the floor, if carpeted, or on the
shipping carton, with the playing

surface down. (Take care not to
damage the playing surface).

FIGURE 4

8. Open legs #25 and #26 and lock leg
hinges.

9. Place leg caps #2 on ends of legs #25
and #26. (See figure 4)

3