Escalade sports T8275 User Manual

OWNER’S MANUAL
Table Tennis Table

Be sure to write your model number and serial number here
for future reference. You can find these numbers printed on
the bottom of the table.

Patent Pending

MODEL # T8275
SERIAL #

READ ASSEMBLY, OPERATING AND SAFETY INSTRUC-

CAUTION:

TIONS CAREFULLY! AT LEAST TWO ADULTS ARE NEEDED
TO PUT THIS TABLE TOGETHER!

Thank you for buying our product. We try hard to ensure that our products are of high quality and free of problems, such as
manufacturing defects or missing parts. However, if you have any problems with your new product, please DO NOT RETURN IT

TO THE STORE!.

DO NOT RETURN THIS PRODUCT TO THE STORE!

Call us at:

TOLL FREE 1-800-426-1421

Please have this Owner’s Manual with you when you call.

Or write us at: CUSTOMER SERVICE DEPT., P.O. Box 889, Evansville, IN 47706

(THIS IS A CONSUMER ONLY NUMBER)

Fax Number: [phone].

Or E-mail us at: [e-mail]

Please provide model number and/or part number (not just the key number) of the product and/or part when you call or write. These numbers
can be found on the product, packaging, and/or in this Owner’s Manual.

TOOLS NEEDED:

Phillips Screwdriver, Two 7/16 Wrenches, One 3/8 Wrench (an adjustable wrench may be substituted for the
wrenches), Scissors, Tape Measure

2L-6617-03

1. Gently tap a caster socket #12 into each Upright Tube
#21 until flange on sockets touches the edge of the tube.

DO NOT HIT CASTER SOCKET TOO HARD WITH A HAM­MER! Sockets may break if hit too hard.

2. Insert casters #11 into caster sockets #12.

3. Attach two Upright Tube Assemblies to both Name Plates

Figure 2

Figure 1

#5, as shown in Figure 2, using four bolts #31 and four
nuts #15.

NOTE: Dimples on Upright Tube #21 need to be against
Name Plate #5.

Figure 3

4. Connect the two Name Plate Assemblies to the Bottom Board #28, as shown in Figure 3, using four bolts #9 and four
nuts #15.

5. Install a safety latch #8 into the right-hand hole on each name panel as shown in Figure 3. Use one screw #10 one
washer #17 and one hex nut #16. NOTE: Flange on safety latch must extend over top of name panel as shown in

Figure 3. Safety latch must pivot freely.

INSTALL SAFETY LATCHES #8 AS SHOWN ABOVE FOR PROPER USE

CAUTION:

6. Rotate U-support #7 until you see the screw holes in
the slots of U-clips # 6. Slide U-support #7 side to side
if necessary. See Figure 4.

7. Insert a screw #19 through slot in each U-clip #6 and
into U-support #7. Thread each screw all the way into
U-support #7 until it touches the back of the tube.
There should be about 3/8 inch of screw #19 left
sticking out.

8. Rotate U-leg #2 until you see the screw holes in the
slots of U-clips #3. Slide U-leg #2 side to side if
necessary. See Figure 4.

9. Insert a screw #34 through slot in each U-clip #3 and
into U-leg #2. Thread each screw all the way into U-leg
#2 until it touches the back of the tube. There should
be about 3/8 inch of screw #19 left sticking out.

OF TABLE! DO NOT SKIP THIS STEP! DO NOT OPERATE TABLE UNTIL
SAFETY LATCHES ARE INSTALLED AND ASSEMBLY IS COMPLETE!

Figure 4

2

10. Lay table top #1 painted side down, on a smooth, flat sur­face. Use the shipping container to protect the painted
surface of the table top.

11. Attach linkages #4 to INSIDE of U-leg #2 as shown in
Figure 5. Secure with screws #14, locknuts #16 and plas­tic washers #24. Tighten hardware snug enough to keep
table stable but do not overtighten. Tubes must pivot freely.
NOTE: Plastic washers go between linkages #4 and U-leg
#2.

12. Attach other end of linkages #4 to OUTSIDE of U-support
#7 with screws #18, locknuts #16 and plastic washers
#24. Tighten hardware until snug but do not overtighten.
Tubes must pivot freely.

Figure 5

13. Attach Corner Cap #22 to bottom of table, as shown
in Figure 6, using three screws #20 per Corner Cap.

14. Attach Side Cap #23 to bottom of table, as shown in
Figure 6, using two screws #20 per Corner Cap.

15. Snap Lower Paddle Box #32 to Upper Paddle Box #33.

Figure 6

16. Prepare an area for the assembly of the second table top
half. If necessary, move the first table top half aside with
the aid of a helper. Be sure to place it in a location where
it won't be disturbed or damaged. If setting on its side, be
sure to place the bottom edge no less than 12 inches
away from the wall. Also be sure to place carpet or pieces
of the shipping carton down to protect table top edges. If
floor is not carpeted, brace table top half with a heavy
object to keep it from sliding.

17. Repeat steps 6 thru 15 on second table half.

AT LEAST TWO (2) ADULTS ARE NEEDED TO
COMPLETE THE REST OF THIS ASSEMBLY!
WHEN ASSEMBLING TOPS TO BASE, HANDLE
TOP ASSEMBLIES BY GRASPING ONLY THE
TOPS THEMSELVES. DO NOT GRASP METAL
LEGS, U-SUPPORT, LINKAGE, OR HINGES.
THESE PARTS CAN MOVE AND COULD PINCH
FINGERS OR HANDS CAUSING SERIOUS
INJURY! ASSEMBLE AS SHOWN WITH LEGS
FULLY CLOSED AND TOPS IN A VERTICAL
POSITION. DO NOT OPEN LEGS AND TRY TO
ASSEMBLE. TABLE TOPS ARE HEAVY - DO NOT
ATTEMPT TO ASSEMBLE ALONE!

Figure 7

18. With two adults, attach table top (#1) to table base, as
shown in Figure 7. With at least one adult on each side of
table top, lift top and align ends of "U"-support tube with
top of upright tubes. Slide tubes together.

19. With two adults, put other table top onto other pivot tubes
following instructions in step 2.

DO NOT OPEN THE TABLE TO PLAYING POSITION
UNTIL BOTH TOPS ARE INSTALLED! DO NOT LEAVE
TABLE STANDING UNATTENDED. IT COULD BE
KNOCKED OVER CAUSING SERIOUS BODILY INJURY
OR PROPERTY DAMAGE.

3