Escalade sports T8271 User Manual

OWNER'S MANUAL

MODEL NOs.

T8271

FOLD AND ROLL PLAYBACK

TABLE TENNIS TABLE

Patent No. 5816957

Thank you for buying our product. We try hard to ensure that our products are of high quality and
free of problems, such as manufacturing defects or missing parts. However, if you have any
problems with your new product, please DO NOT RETURN IT TO THE STORE!.

DO NOT RETURN THIS PRODUCT TO THE STORE!

Call us at:

TOLL FREE 1-800-426-1421

(THIS IS A CONSUMER ONLY NUMBER)

Please have this Owner’s Manual with you when you call.

WARRANTY

Actual product may

differ slightly from that

shown in illustrations.

Or write us at: CUSTOMER SERVICE DEPT., P.O. Box 889, Evansville, IN 47706

Or E-mail us at: [e-mail]

Please provide model number and/or part number (not just the key number) of the product and/or part when
you call or write. These numbers can be found on the product, packaging, and/or in this Owner’s Manual.

Manufacturer warrants to the original retail purchaser, this product to be free from defects in material and
workmanship for a period of one (1) year from the date of purchase.

Should this product become defective due to material or workmanship within the warranty period, contact
our Customer Service Department for repair or replacement at our option.

This warranty is not transferable and does not cover normal wear and tear, bowing of the table or damage
caused by improper handling, installation or use of this product. This warranty is also void if product is in
any way abused, damaged, or modified from its original state, or if used for other than residential use.

This warranty gives you specific legal rights, and you may have other rights which vary from state to state.

Fax Number: [phone].

LIMITED 1 YEAR WARRANTY

CA UTION

THIS IS A GAME TABLE. DO NOT SIT, STAND, LEAN, WALK OR JUMP ON TABLE! FAILURE TO
COMPLY WITH THIS CAUTION COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY
DAMAGE!

This table must be kept indoors to prevent damage to the playing surface. Dampness and extreme
temperature changes which occur on patios, garages or similar areas can cause wood to warp, swell,
crack, or blister.

UNLEVEL FLOORS

If table does not seem level, it is probably because floor is not level. Move table several inches (set
table in playing position) in different directions to find the best location for the table. If the floor is
extremely unlevel, table may not play or operate properly. If table is high in the center, shim up under
the outer legs.

READ ASSEMBLY &

OPERATING INSTRUCTIONS

AND ALL SAFETY

INFORMATION CAREFULLY!

© 2001 Escalade Sports

TABLE TENNIS WARRANTY CENTER, P.O. BOX 889, EVANSVILLE, IN 47706-889 2L-6547-01

CARE AND MAINTENANCE

You have purchased a quality product that will give you years of enjoyment. By following these simple
maintenance steps you will add to the life of your new table. The top (playing surface) of your table is of a particle
board construction. Like all products made of wood, it can be affected by atmospheric conditions, meaning both
temperature and humidity. This may cause a slight sag or distortion as top expands or contracts. This is normal
and should not cause concern as it does not detract from the play or utility value of the table. To help minimize
this problem, store table in folded up position in a dry area when not in use.

STORAGE OF YOUR TABLE
This table must be stored indoors to prevent damage to the playing surface. Dampness and extreme

temperature changes which occur on patios, garages or similar areas can cause the wood to warp, swell, crack,
or blister. When your table is not in use, it should be folded up in a dry area.

CLEANING YOUR TABLE
To clean your table use a soft damp NOT WET cloth only. To prevent damage to your table's playing surface
DO NOT use any chemicals, abrasive, or cleaning products on your table's playing surface.
IMPORTANT: Periodically, lubricate all moving parts, including pivot points, to assure smooth opening and

closing. A light lubricant such as WD-40 is recommended.

1

1. Locate one "R" pivot bracket (#7) and one "L"
pivot bracket (#9). NOTE: Pivot brackets have

an "R" or "L" stamped on the front of them
to make them easy to identify. Attach "R" and

"L" pivot brackets and pivot tubes (#8) to caster
rail (#1), with the angles toward the ends of the
caster rail (See Figure 1b), using one hex bolt
(#22), two nylon washers (#32) and one locknut

(#31). See Figure 1. Do NOT overtighten bolts

securing pivot tubes. Pivot tubes should pivot
freely.

2. Secure pivot brackets to caster rail with two hex

bolts (#23) and locknuts (#31). Tighten hex bolts
snugly.

Figure 1

3. Insert a caster wheel (#5) through the hole at

each end of the caster rail, as shown in Figure

1. Tap a palnut (#6) onto the shaft protruding
through the top of the caster rail.

Figure 1b

4. Tap a square plug (#29) into each end of the caster

rail.

5. Repeat steps 1 through 4 for second caster rail.

2