Escalade sports T8220-1 User Manual

OWNER'S

MANUAL

MODEL NOS.

T8220-1

EXPERT ROLLER

Thank you for buying our product. We try hard to ensure that our products are of high quality and
free of problems, such as manufacturing defects or missing parts. However, if you have any
problems with your new product, please DO NOT RETURN IT TO THE STORE!.

DO NOT RETURN THIS PRODUCT TO THE STORE!

Call us at:

TOLL FREE 1-866-873-3528

(THIS IS A CONSUMER ONLY NUMBER)

Please have this Owner’s Manual with you when you call.

CAUTION

READ THESE

INSTRUCTIONS

CAREFULLY!

Or write us at: CUSTOMER SERVICE DEPT., P.O. Box 889, Evansville, IN 47706

Fax Number: [phone].

Or E-mail us at: [e-mail]

Please provide model number and/or part number (not just the key number) of the product and/or part
when you call or write. These numbers can be found on the product, packaging, and/or in this Owner’s
Manual.

Tools Needed: ! Two 7/16 Open \ Boxed End Wrenches ! Two ½ Wrenches

! Tape Measure ! Two 9/16 Open \ Boxed End Wrenches

2L-6670-00

1. ATTACHING LEGS TO TABLE TOPS

AT LEAST TWO ADULTS ARE NEEDED TO

CAUTION

COMPLETE THE FOLLOWING STEPS!

1. Leave top halves #1 in shipping carton as shown

above or lay them on a carpeted floor (

them from damage and scratches

2. Attach leg assembly #10 to brackets #6 located
on the bottom of the first top half #1. (See above).
Use bolts #26, spacers #20 and locknuts #28.
(See Detail A).

NOTE: Be sure brace on leg assembly #10 is
against table and hole in the middle of leg

assembly #10 is nearer the top of tube. (See

Detail B).
Tighten these locknuts snug but DO NOT

OVERTIGHTEN THEM. JOINT MUST MOVE!

to protect

).

3. Put caps #21 on bottom end of leg assembly
#10. (See Detail C).

4. Attach upright assembly #11 to remaining
brackets #6 on the bottom of the first top half #1.
(See above). Use bolts #26, spacers #20, and
locknuts #28. (See Detail D). Tighten locknuts
snug but DO NOT OVERTIGHTEN THEM.

JOINT MUST MOVE!

5. With a helper, set the first top half #1 on its side

against a wall. (

cardboard, cloth, or carpeting on the floor first to
protect the top's edges.

half #1 over and repeat steps 2-4 to assemble it.

2

Be sure to put a piece of

) Turn the second top

2. ATTACHING NAME PANELS TO LEGS

AT LEAST TWO ADULTS ARE NEEDED TO COMPLETE THEAT LEAST TWO ADULTS ARE NEEDED TO COMPLETE THE

AT LEAST TWO ADULTS ARE NEEDED TO COMPLETE THE

AT LEAST TWO ADULTS ARE NEEDED TO COMPLETE THEAT LEAST TWO ADULTS ARE NEEDED TO COMPLETE THE
FOLLOWING STEPS! DO NOT LEAVE TABLE UNATTENDED UNTILFOLLOWING STEPS! DO NOT LEAVE TABLE UNATTENDED UNTIL

FOLLOWING STEPS! DO NOT LEAVE TABLE UNATTENDED UNTIL

CAUTION

FOLLOWING STEPS! DO NOT LEAVE TABLE UNATTENDED UNTILFOLLOWING STEPS! DO NOT LEAVE TABLE UNATTENDED UNTIL
ASSEMBLY IS COMPLETE!ASSEMBLY IS COMPLETE!

ASSEMBLY IS COMPLETE!

ASSEMBLY IS COMPLETE!ASSEMBLY IS COMPLETE!

6.6.

With a helperWith a helper

6.

With a helper

6.6.

With a helperWith a helper
inches apart. inches apart.

inches apart. Attach only

inches apart. inches apart.

panels #8 to upright assemblies #11 as shown
above. Use

on each name panel.on each name panel.

#29

on each name panel.

on each name panel.on each name panel.

(

Two other bolts #27 and nuts #29 will be used in

, hold top halves about 15 ½, hold top halves about 15 ½

, hold top halves about 15 ½

, hold top halves about 15 ½, hold top halves about 15 ½

one halfone half

one half of name

one halfone half

ONLY TWOONLY TWO

ONLY TWO bolts #25 and locknuts

ONLY TWOONLY TWO

the next section to attach the other half of the
name panels and linkages #24 at the same time.
See next page.

completely tight yetcompletely tight yet

completely tight yet.

completely tight yetcompletely tight yet

Do not tighten these locknutsDo not tighten these locknuts

)

Do not tighten these locknuts

Do not tighten these locknutsDo not tighten these locknuts

HELPFUL HINT: HELPFUL HINT:

HELPFUL HINT: Start at the bottom and insert

HELPFUL HINT: HELPFUL HINT:

two bolts #25
assemblies #11 and name panel #8. Then attach
the upper name panel #8. Insert bolts #25

DOWNWARDDOWNWARD

DOWNWARD.

DOWNWARDDOWNWARD
NOTE: Be sure that top halves #1 lock intoNOTE: Be sure that top halves #1 lock into

NOTE: Be sure that top halves #1 lock into

NOTE: Be sure that top halves #1 lock intoNOTE: Be sure that top halves #1 lock into
the safety latches on each name panel.the safety latches on each name panel.

the safety latches on each name panel.

the safety latches on each name panel.the safety latches on each name panel.

7.7.

7. Slide caps #22 onto ends of safety latches. (See

7.7.

Detail E)

3

UPWARDUPWARD

UPWARD through upright

UPWARDUPWARD