Escalade sports T8219 User Manual

OWNER’S MANUAL

MODEL # T8219, 527.26302

Table Tennis Table

SERIAL #

Patent Pending

READ ASSEMBLY, OPERATING AND SAFETY INSTRUC-

CAUTION:

Thank you for buying our product. We try hard to ensure that our products are of high quality and free of problems, such as manufacturing
defects or missing parts. However, if you have any problems with your new product, please DO NOT RETURN IT TO THE STORE!.

DO NOT RETURN THIS PRODUCT TO THE STORE!

Or write us at: CUSTOMER SERVICE DEPT., P.O. Box 889, Evansville, IN 47706

TIONS CAREFULLY! AT LEAST TWO ADULTS ARE NEEDED
TO PUT THIS TABLE TOGETHER!

Call us at:

TOLL FREE 1-866-873-3528

(THIS IS A CONSUMER ONLY NUMBER)

Please have this Owner’s Manual with you when you call.

Fax Number: [phone].

Or E-mail us at: [e-mail]

Please provide model number and/or part number (not just the key number) of the product and/or part when you call or write. These numbers can be found
on the product, packaging, and/or in this Owner’s Manual.

TOOLS NEEDED:

Phillips Screwdriver , Two 7/16 Wrenches , One 3/8 Wrench (an adjustab le wrench may be substituted f or the wrenches).

2L-6647-00

1. Lay table top #1 painted side down, on a smooth, flat
surface. Use the shipping container to protect the painted
surface of the table top.

2. Assemble the two “L” tubes and the center tubes that mak e
up the “U” Support and the “U” Leg. Align on Table Top as
shown in Figure 1. Note: “U” Leg is larger and wider than

the U Support. The U-leg should be installed on the end
of the table half with the end rail.

3. Put plastic caps #13 on the end of U-leg #2.

4. Lay Corner Caps #22 on table as shown in Figure 2. If

Corner Cap sticks above table top surface of table, flip
over so shorter distance is against edge. Secure to bot­tom of table with three screws #21.

Figure 1

Figure 2

5. Align the holes in the U-clips #3 with pilot holes in table
top assembly and secure with twenty four screws #20 as
shown in figure 3.

IMPORTANT:

Be sure the slot in the six U-clips #3 all face the
same direction (toward the end of the table with the
U-support) as shown.

Figure 3

IMPORTANT: U-Leg is wider than U-support.
Make sure they are assembled exactly as
shown. If not, there will be a large gap between
table halves and table will not operate
properly!

2

6. Rotate U-support #7 until you see the screw hole

in the slot of U-clip # 3. Slide U-support #7 side to
side if necessary.

7. Insert screw #19 through slot in U-clip #3 and into

U-support #7. Thread it all the way into U-support
#7 until it touches the back of the tube. There
should be about 3/8 inch of screw #19 left sticking
out. Repeat for U Leg #2.

8. Attach end of linkages #4 with two holes to INSIDE of U-leg #2

as shown in Figure 5. Secure through end hole with screws
#23, locknuts #15 and plastic spacers #31. Tighten hardware
snug enough to keep table stab le but do not o v ertighten. Tubes
must pivot freely.

9. On one side of the table attach slotted end of safety strap #6 to

INSIDE of U-Leg #2 using one bolt #29, one spacer #30, one
washer #24, and one hex nut #15. Tighten hardware until snug
but do not overtighten. Tubes must pivot freely. See Figure 6.

10. Attach other end of safety strap #6 to OUTSIDE of linkage #4

using one bolt #9, one washer #24, one spacer #30, and one
hex nut #15.

Figure 4

Figure 5

11. Attach other end of linkages #4 to OUTSIDE of U-support #7

with screws #14 and plastic washers #24. Then slide name
panel #5 onto the same screws #14 on INSIDE of U-support
#7. Secure with locknuts #15. Tighten hardware until snug but
do not overtighten. Tubes must pivot freely.

12. Attach bottom of name panel #5 to U-supports #7. Secure with

hex bolts #9 and locknuts #15. Tighten nuts but be careful not
to crush tubes. See Figure 6.

13. Gently tap caster sockets #12 into U-support #7 until flange

on sockets touches the edge of the tube. DO NOT HIT CASTER
SOCKET TOO HARD WITH A HAMMER! Sockets ma y break
if hit too hard.

14. Insert casters #11 into caster sockets #12.

CAUTION:

AT LEAST TWO ADULTS ARE

NEEDED TO MOVE TABLE HALF!

15. Prepare an area for the assembly of the second table top

half. If necessary, move the first table top half aside with the
aid of a helper. Be sure to place it in a location where it won't
be disturbed or damaged. If setting on its side, be sure to
place the bottom edge no less than 12 inches away form the
wall. Also be sure to place carpet or pieces of the shipping
carton down to protect table top edges. If floor is not carpeted,
brace table top half with a heavy object to keep it from sliding.

Figure 6

Figure 7

3