Escalade sports T8190 User Manual

MODEL NO.

T8190T8190

T8190

T8190T8190

AEROTECH

TABLE TENNIS TABLE

OWNER'S MANUAL

1. Read this manual carefully before starting assembly. Read each step completely before beginning

each step.

2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons
before assembling or ordering parts.

3. To make assembly easier, use the Hardware Identifier on page 7 to identify and sort all
fasteners. Check all cartons for kits. All hardware may not be located in one kit.

4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes

may not align and parts may not easily fit together. Leave locknuts slightly loose until you are instructed to
tighten them.

5. Tools required for assembly: Phillips Screwdriver, Two 7/16 Wrenches, One 3/8 Wrench (an adjustable

wrench may be substituted for the wrenches), Flat Blade Screw Driver

Please Do Not Return This Product To The Store!

Contact Escalade® Sports customer service department at:
Phone: [phone] Toll – Free !
Fax: [phone] Toll – Free !
E-mail: [e-mail]
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706

Please visit our World Wide Web site at: www.escaladesports.com

ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE

ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS

ADDITIONAL ESCALADE® SPORTS PRODUCT INFORMATION

Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.

2L-6862-01

1. Insert one caster with brake #33 and one caster without brake #32
into caster sockets in each side panel assembly #35. See Figure 1.

2. Connect the a side panel assembly #35 to the Bottom Board #36,
as shown in Figure 1, using four bolts #37 and four wing nuts #38.

3. Repeat step 2 for other side panel assembly #35.

Figure 1

Figure 2

4. Lay table top #1 painted side down, on a smooth, flat surface. Use
the shipping container to protect the painted surface of the table
top.

5. Rotate U-support #21 until you see the screw holes in the slots of U­clips #22. Slide U-support #21 side to side if necessary. See Figure

2.

6. Insert a screw #39 through slot in each U-clip #22 and into U­support #21. Thread each screw all the way into U-support #21
until it touches the back of the tube. There should be about 3/8 inch
of screw #39 left sticking out.

7. Rotate U-leg #2 until you see the screw holes in the slots of U-clips
#6. Slide U-leg #2 side to side if necessary. See Figure 2.

8. Insert a screw #8 through slot in each U-clip #6 and into U-leg #2.
Thread each screw all the way into U-leg #2 until it touches the
back of the tube. There should be about 3/8 inch of screw #8 left
sticking out.

2

9. Locate one three hole linkage #11 and one two hole linkage #10
and insert a tube plug #24 in each end. See Figure 3

Figure 4

Figure 3

10. Attach bent end of three hole linkage #11to INSIDE of U-leg #2

with two holes as shown in Figure 4. Secure with bolts #12, lock­nuts #14 and plastic spacers #13. Tighten hardware snug enough
to keep table stable but do not overtighten. Tubes must pivot freely.
NOTE: Plastic spacers go between linkage #11 and U-leg #2.

11. Attach bent end of two hole linkage #10 to INSIDE of U-leg #2

with one hole as shown in Figure 4. Secure with bolts #12, locknuts
#14 and plastic spacers #13. Tighten hardware snug enough to
keep table stable but do not overtighten. Tubes must pivot freely.
NOTE: Plastic spacers go between linkage #10 and U-leg #2.

12. Attach other end of linkages #10 and #11 to OUTSIDE of U-

support #21 with bolts #23, locknuts #14 and plastic washers
#18. Tighten hardware until snug but do not overtighten. Tubes
must pivot freely.

13. Install leg cap #15 onto end of U-legs #2.

16. Prepare an area for the assembly of the second table top half. If

necessary, move the first table top half aside with the aid of a helper.
Be sure to place it in a location where it won't be disturbed or dam­aged. If setting on its side, be sure to place the bottom edge no less
than 12 inches away from the wall. Also be sure to place carpet or
pieces of the shipping carton down to protect table top edges. If
floor is not carpeted, brace table top half with a heavy object to
keep it from sliding.

17. Repeat steps 5 thru 15 on second table half.

AT LEAST TWO (2) ADULTS ARE NEEDED TO COMPLETE
THE REST OF THIS ASSEMBLY! WHEN ASSEMBLING TOPS
TO BASE, HANDLE TOP ASSEMBLIES BY GRASPING ONLY
THE TOPS THEMSELVES. DO NOT GRASP METAL LEGS, U­SUPPORT, LINKAGE, OR HINGES. THESE PARTS CAN
MOVE AND COULD PINCH FINGERS OR HANDS
CAUSING SERIOUS INJURY! ASSEMBLE AS SHOWN WITH
LEGS FULLY CLOSED AND TOPS IN A VERTICAL POSITION.
DO NOT OPEN LEGS AND TRY TO ASSEMBLE. TABLE TOPS
ARE HEAVY - DO NOT ATTEMPT TO ASSEMBLE ALONE!

14. On one side of the table attach slotted end of safety strap #19 to

INSIDE of U-Leg #2 using one black bolt #20, one spacer #16,
one washer #18, and one locknut #14. Tighten hardware until
snug but do not overtighten. Tubes must pivot freely. See Detail A.

15. Attach other end of safety strap #19 to OUTSIDE of three hole

linkage #11 using one bolt #17, one washer #18, one spacer
#16, and one locknut #14.

Figure 5

18. With two adults, attach table top #1 to table base, as shown in

Figure 5. With at least one adult on each side of table top, lift top
and align ends of "U"-support tube with top of upright tubes. Slide
tubes together.

19. With two adults, put other table top onto other pivot tubes following

instructions in previous step.

20. Attach corner caps #9 to outer corners of tops. See Figure 5.

21. Push two hole plugs #25 into holes in each apron. See Figure 5.

DO NOT OPEN THE TABLE TO PLAYING POSITION
UNTIL BOTH TOPS ARE INSTALLED! DO NOT LEAVE
TABLE STANDING UNATTENDED. IT COULD BE
KNOCKED OVER CAUSING SERIOUS BODILY INJURY
OR PROPERTY DAMAGE.

3