Escalade sports T8158 User Manual

MODEL NOS.

T8158T8158

T8158

T8158T8158

Nova

TABLE TENNIS TABLE

OWNER'S MANUAL

1. Read this manual carefully before starting assembly. Read each step completely before beginning

each step.

2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons
before assembling or ordering parts.

3. To make assembly easier, use the Hardware Identifier on page 7 to identify and sort all
fasteners. Check all cartons for kits. All hardware may not be located in one kit.

4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes

may not align and parts may not easily fit together. Leave locknuts slightly loose until you are instructed to
tighten them.

5. Tools required for assembly: Phillips Screwdriver, 3/8 Wrench, and Two 7/16 Wrenches (adjustable

wrenches may be substituted for the wrenches).

Please Do Not Return This Product To The Store!

Contact Escalade® Sports customer service department at:
Phone: [phone] Toll – Free !
Fax: [phone] Toll – Free !
E-mail: [e-mail]
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706

Please visit our World Wide Web site at: www.escaladesports.com

ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE

ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS

®

ADDITIONAL ESCALADE

SPORTS PRODUCT INFORMATION

2L-6801-00

Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.

For aid in identifying hardware, see hardware identifier on page 9.

Figure 1

1. Lay table top #1 painted side down, on a smooth, flat

surface. Use the shipping container to protect the
painted surface of the table top.

2. Assemble the two “L” tubes and the center tubes that

make up the “U” Support and the “U” Leg. Align on
Table Top as shown in Figure 1. Note: “U” Leg is

larger and wider than the U Support. The U­leg should be installed on the end of the table
half with the end rail mounting holes.

3. Put plastic caps #13 on the end of U-leg #2.

4. Align the holes in the U-clips #3 with pilot holes in table top

assembly and secure with twenty four screws #20 as shown.

IMPORTANT:

Be sure the slot in the six U-clips #3 all face the same
direction (toward the end of the table with the U­support) as shown.

Figure 2

IMPORTANT: U-Leg is wider than U-support.
Make sure they are assembled exactly as
shown. If not, there will be a large gap between
table halves and table will not operate properly!

2

5. Lay out rails #25 and 26, as shown in Figure 3, around edges

of table top.

6. Line up holes in rails with pilot holes in top and secure using

eighteen screws #20. See Figure 3.

Figure 3

7. Lay Corner Caps #22 on table as shown in Figure 4. If Corner

Cap sticks above table top surface of table, flip over so shorter
distance is against edge. Secure to bottom of table with three
screws #21.

8. Rotate U-support #7 until you see the screw hole in
the slot of U-clip # 3. Slide U-support #7 side to side
if necessary.

9. Insert screw #19 through slot in U-clip #3 and into
U-support #7. Thread it all the way into U-support
#7 until it touches the back of the tube. There should
be about 3/8 inch of screw #19 left sticking out. Re­peat for U Leg #2.

Figure 4

Figure 5

3