Escalade sports T8128 User Manual
MODEL NO.
T8128T8128
T8128
T8128T8128
TABLE TENNIS TABLE
OWNER'S MANUAL
1. Read this manual carefully before starting assembly. Read each step completely before beginning
each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons
before assembling or ordering parts.
3. To make assembly easier, use the Hardware Identifier on page 11 to identify and sort all
fasteners. Check all cartons for kits. All hardware may not be located in one kit.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes
may not align and parts may not easily fit together. Leave locknuts slightly loose until you are instructed to
tighten them.
5. Tools required for assembly: Phillips Screwdriver, Two 7/16 Wrenches, One 3/8 Wrench (an adjustable
wrench may be substituted for the wrenches).
Please Do Not Return This Product To The Store!
Contact Escalade® Sports customer service department at:
Phone: 1-866-873-3528 Toll – Free !
Fax: 1-866-873-3533 Toll – Free !
E-mail: tabletennis@escaladesports.com
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
Please visit our World Wide Web site at: www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
®
ADDITIONAL ESCALADE
SPORTS PRODUCT INFORMATION
2L-7027-00
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.
2005 Escalade
Sports
1. Lay table top #1 painted side down, on a smooth, flat
surface. Use the shipping container to protect the
painted surface of the table top.
2. Assemble the two “L” tubes and the center tubes that
make up the “U” Support and the “U” Leg. Align on
Table Top as shown in Figure 1. Note: “U” Leg is
larger and wider than the U Support. The Uleg should be installed on the end of the table
half with the end rail mounting holes.
3. Put plastic caps #13 on the end of U-leg #2.
Figure 1
7
U-Support
13
13
4. Align the holes in the U-clips #3 with pilot holes in
table top assembly and secure with twenty four screws
#20 as shown.
IMPORTANT:
Be sure the slot in the six U-clips #3 all face the same
direction (toward the end of the table with the Usupport) as shown.
Slot in
U-Clip
2
U-Leg
End Rail
Mounting
Holes
2
U-Leg
3
All screws shown
are (#20) sheet
metal screws.
3
U-Support
Figure 2
20
3
3
3
3
IMPORTANT: U-Leg is wider than U-support.
Make sure they are assembled exactly as
shown. If not, there will be a large gap between
table halves and table will not operate properly!
7
2
5. Lay out rails #25 and 26, as shown in Figure 3, around
edges of table top.
6. Line up holes in rails with pilot holes in top and secure
using eighteen screws #20. See Figure 3.
(48” Rail)
25
Figure 3
20
All screws shown
are (#20) sheet
metal screws.
25
(48” Rail)
7. Lay Corner Caps #24 on table as shown in Figure 4.
If Corner Cap sticks above table top surface of table,
flip over so shorter distance is against edge. Secure to
bottom of table with three screws #18.
Figure 4
26
(53” Rail)
Shorter Distance
18
24
Longer Distance
Bottom of Table
3
8. Rotate U-support #7 until you see the screw hole in the
14
6
21
16
14
4
21
16
2
Right hand
hinge has “R”
stamped on it.
Left hand
hinge has “L”
stamped on it.
14
4
21
16
14
6
21
16
slot of U-clip # 3. Slide U-support #7 side to side if
necessary.
9. Insert screw #19 through slot in U-clip #3 and into Usupport #7. Thread it all the way into U-support #7
until it touches the back of the tube. There should be
about 3/8 inch of screw #19 left sticking out. Repeat
for U Leg #2.
Note: Slide U-support back and forth until you
see the hole if necessary.
19
3
U-Support
Figure 5
7
U-Support
10. Attach hinge and brackets #6 and #4 to U-leg #2 as
shown in Figure 6. NOTE: Hinges are right hand
and left hand and must be attached as shown.
Left hand hinge #6 has the letter “L” stamped on it and
the right hand hinge has “R”. Attach with screws #14,
plastic washers #21 and locknuts #16. Tighten nuts
until snug, but do not overtighten. Hinges must pivot.
See Figure 6.
Figure 6
Wider
U-Leg
2
U-Leg
19
3
4
Loading...