Escalade sports T8126 User Manual

MODEL NO.

T8126

TABLE TENNIS TABLE

OWNER'S MANUAL

1. Read this manual carefully before starting assembly. Read each step completely before beginning
each step.

2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons
before assembling or ordering parts.

3. To make assembly easier, use the Hardware Identifier on page 9 to identify and sort all
fasteners. Check all cartons for kits. All hardware may not be located in one kit.

4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes

may not align and parts may not easily fit together. Leave locknuts slightly loose until you are instructed to
tighten them.

5. Tools required for assembly: Phillips Screwdriver, Two 7/16 Wrenches, One 3/8 Wrench (an adjustable

wrench may be substituted for the wrenches).

Please Do Not Return This Product To The Store!

Contact Escalade® Sports customer service department at:
Phone: [phone] Toll  Free !
Fax: [phone] Toll  Free !
E-mail: [e-mail]
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706

Please visit our World Wide Web site at: www.escaladesports.com

ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE

ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS

®

ADDITIONAL ESCALADE

SPORTS PRODUCT INFORMATION

2L-7029-00

Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product.

Ó2005 EscaladeÒSports

1. Tap a caster socket #12 into one end of each of the four

18

17

15

Side Panel

Assembly

Side Panel

Assembly

caster tubes #27 until flange on socket touches the
edge of the tube. See figure 1. DO NOT HIT CASTER

SOCKETS DIRECTLY WITH A HAMMER! SET A
PIECE OF WOOD ON CASTER SOCKET AND
HIT WOOD TO DRIVE SOCKET INTO TUBE.

Sockets may break if hit too hard.

2. Insert casters #11 into caster sockets #12. See

figure 1.

3. Insert two safety latches #8 into slots in side panel #5

as shown in figure 1 and attach with two screws #10
and two locknuts #16. Tighten nuts snug, but do not
over-tighten. You could crack plastic side panel.

4. Insert caster tubes #27 into side panels #5. See figure

1. Be sure tubes are inserted all the way into side panel.
You will have 3" of tube inside side panel.

Figure 1

8

5

Mark tube with a pencil or
a piece of tape, and insert

tube until you reach the mark

10

16

3”

27

12

5. Connect the two side panel assemblies (that you just put to-

gether) to the bottom board #17 using four bolts #18 and four
locknuts #15. See figure 2.

11

Figure 2

2

6. Lay table top #1 painted side down, on a smooth, flat

surface. Use the shipping container to protect the
painted surface of the table top.

Figure 3

7

U-support

7. Assemble the two L tubes and the center tubes that

make up the U Support and the U Leg. Align on
Table Top as shown in Figure 3. Note: U Leg is

larger and wider than the U Support. The U­leg should be installed on the end of the table
half with the end rail mounting holes.

8. Put plastic caps #13 on the end of U-leg #2.

9. Align the holes in the U-clips #3 with pilot holes in table top

assembly and secure with twenty four screws #20 as shown.

End Rail

Mounting

Holes

13

20

13

2

U-Leg

3

3

All screws shown
are (#20) sheet
metal screws.

3

IMPORTANT:

Be sure the slot in the six U-clips #3 all face the same
direction (toward the end of the table with the U­support) as shown.

Slot in
U-Clip

2

U-Leg

3

End Rail

Mounting

Holes

3

7

U-support

3

3

Figure 4

IMPORTANT: U-Leg is wider than U-support.
Make sure they are assembled exactly as
shown. If not, there will be a large gap between
table halves and table will not operate properly!