Escalade Sports 2L-6516-01 User Manual
OWNER'S
MANUAL
For Model No.
T8261
CAUTION
READ THESE
INSTRUCTIONS
CAREFULLY!
S P O R T S
Thank you for buying our product. We try hard to ensure that our products are of high quality and free
of problems, such as manufacturing defects or missing parts. However, if you have any problems with
your new product, please DO NOT RETURN IT TO THE STORE!.
DO NOT RETURN THIS PRODUCT TO THE STORE!
Call us at:
TOLL FREE 1-800-426-1421
(THIS IS A CONSUMER ONLY NUMBER)
Please have this Owner’s Manual with you when you call.
Or write us at: CUSTOMER SERVICE DEPT., P.O. Box 889, Evansville, IN 47706
Fax Number: (812) 467-1399.
Or E-mail us at: customerservice@escaladesports.com
Please provide model number and/or part number (not just the key number) of the product and/or part when you
call or write. These numbers can be found on the product, packaging, and/or in this Owner’s Manual.
LIMITED 1 YEAR WARRANTY
Manufacturer warrants to the original retail purchaser, this product to be free from defects in material
and workmanship for a period of one (1) year from the date of purchase. Should this product become
defective due to material or workmanship within the warranty period, contact our Customer Service
Department. If defective by the terms of this warranty, we will, at our option, repair or replace the
product. This warranty is not transferable and does not cover normal wear and tear, or damage
caused by improper handling, installation or use of this product. This warranty is also void if product
is in any way abused, damaged, or modified from its original state. This warranty gives you specific
legal rights, and you may have other rights which vary from state to state.
2L-6516-01
TOOLS NEEDED FOR ASSEMBLY
AT LEAST TWO ADULTS ARE NEEDED TO COMPLETE THIS
CAUTION
Tools Needed: 7/16 Open or Boxed End Wrenches (2) Rachet (optional)
9/16 Open or Boxed End Wrenches (2) 7/16 Socket (If using rachet)
Pliers 9/16 Socket (If using rachet)
Hammer
CASTER BEAM ASSEMBLY
ASSEMBLY ! DO NOT LEAVE TABLE UNATTENDED
UNTIL ASSEMBLY IS COMPLETE!
5
6
5
FIGURE 1
3
6
1
FIGURE 2
2
1
1. Attach one non - locking caster #3 and
one locking caster #2 to each caster
rail #1 using one washer #6 and one jam
nut #5, as shown in figure 1. Do not
over tighten jam nuts crushing tubes.
2. Place tube plugs #10 into the ends of
caster rails #1. (See figure 2)
3. Attach one mounting plate #4 to each
side of caster rail #1. Secure using two
bolts #18, and two locknuts #9. Do not
tighten locknuts completely until
instructed. (See figure 3)
10
4. Assemble other three caster rails using
steps 1 thru 3.
18
4
4
1
9
FIGURE 3
Orient mounting plates to
tube in this manner
2
ATTACHING UPRIGHTS
8
18
4
Locking casters
MUST be on opposite
Do not place nut
on bolt #18.
FIGURE 4
sides of each other.
Locking casters
MUST be on opposite
sides of each other.
21
9
4
Bolt heads
MUST face
Three holes
go toward
caster rail.
5. Attach two caster rail assemblies to
upright #21 as shown in figure 4.
Placing the end with three holes
towards caster rail. (See figure 4)
Secure using two bolts #8 in the top
holes, two bolts #18 in the bottom
holes, and two locknuts #9 on bolts
#8 ONLY. Do not place locknut #9
on bolt #18 until instructed. (See
figure 4) Secure all bolts.
6. Attach remaining two caster rail
assemblies to other upright #21 in
same manner.
8
18
ATTACHING SAFETY LATCHES
25
25
14
Detail A
Attach hook end
of #13 spring
into this hole.
9
14
9
27
19
13
12
FIGURE 5
21
Attach safety latch
using this hole.
4
8
18
7. Place end protectors #25 on safety latch #14
as shown in detail A.
8. Attach safety latch #14 to upright assembly
#21 using the hole
Secure with bolt #8, spacer #19, safety latch
#14, and locknut #9. Do not over tighten
locknuts, safety latches must be free to
pivot.
Secure the eyelet end of safety latch spring
#13 (See detail B) to upright assembly #21
with bolt #18 that was used in step 5, spacer
#12, washer #27, and locknut #9. (See figure
5)
Using a pair of pliers hook spring #13 into
hole in safety latch #14. (See figure 5)
9. Attach other safety latch to other frame
assembly the same way using step 7 and 8.
above mounting plate #4.
3
Loading...