Escalade Sports 2L-6433-00 User Manual

OWNER'S MANUAL

FOLD AND ROLL PLAYBACK

TABLE TENNIS TABLE

Thank you for buying our product. We try hard to insure that our products are
of high quality and free of problems, such as manufacturing defects or missing
parts. However, if you have any problems with your new product, please call us
at:

TOLL FREE 1-800-426-1421

(THIS IS A CONSUMER ONLY NUMBER)

Please have this Owner’s Manual with you when you call.

MODEL NO.

T8022

527.26203
T80221

527.26209

Or write us at: CUSTOMER SERVICE DEPT., P.O. Box 889

Evansville, IN 47706

Fax Number: [phone].

Please provide model number and/or part number (not just the key number) of the product
and/or part when you call or write. These numbers can be found on the product, packaging,
and/or in this Owner’s Manual.

READ ASSEMBLY &

OPERATING INSTRUCTIONS

AND ALL SAFETY

INFORMATION CAREFULLY!

2L-6433-00

AT LEAST TWO PEOPLE ARE NEEDED TO PUT
THIS TABLE TOGETHER!

You will need the following tools to put your table
together:

o Phillips Screwdriver
o Standard (Flat Blade) Screwdriver
o Hammer or Mallet
o Pliers
o 6' or 8" Crescent Wrench
o 7/16 Wrench
o 3/8 Wrench
o 9/16 Wrench

First Table Half Assembly

1. Open the hardware kit and sort all the hardware. For

your help in identifying hardware, see the hardware
identifier on the front cover of this owner's manual.

2. Lean either table half #1 against a wall placing the two
legs #2 & #3 with hinges near the floor. (See Figure

1). Place bottom of table about 12" from wall.

Figure 1

IMPORTANT NOTE: If floor is not carpeted, be sure
to place a heavy object at the base of the table half
to help prevent table half from sliding away from wall.

3. Pull legs #2 & #3 out from table and lock their hinges

by pulling hinges upward as shown in figure 1, detail.

4. Put caps #13 on ends of both legs #2 & #3. (See Figure

1)

5. Rotate U-support #7 until you see the screw hole in the
slot of U-clip #6 (See Figure 1, Detail). Slide U-support
#7 side to side if necessary.

6. Insert screw #19 through slot in U-clip #6 and into U­support #7. Thread it all the way into U-support #7 until
it touches the back of the tube. There should be about
3/8 inch of screw #19 left sticking out. (See Figure 1)

7. Attach linkages #4 to INSIDE of legs #2 & #3. Secure
with screws #26, spacers #38, locknuts #15 and
thread protectors #23. (See Figure 2) Tighten

hardware snug to keep table stable but do not
overtighten. Tubes must pivot.

8. Attach free end of linkages #4 to OUTSIDE of U-support

#7 with screws #14 and spacers #38. Then slide
braces #9 onto the same screws #14 on INSIDE of U­support #7. Secure with locknuts #15. (See Figure 2)

Tighten snug but do not overtighten. Tubes must
pivot.

Figure 2

2

First Table Half Assembly

(Continued)

Figure 3

9. Put tube plugs #22 into both U-braces #5. (See Figure

3).

10. Gently tap caster sockets #12 into ends of U-supports

#7 until flange on sockets touch the edge of the tube.

DO NOT USE FORCE OR A HAMMER! (See Figure 4).

11. Insert one caster #11 into each caster socket #12.

12. Attach U-brace #5 to U-supports #7. (See Figure 4)

Secure with hex bolts #18 and locknuts #16. Tighten
nuts but be careful not to crush tubes.

Figure 4

Second Table Half Assembly

13. Lean second table half #1 against a wall placing the

two legs #2 & #3 with hinges near the floor. (See

Figure 5). Place bottom of table about 12" from wall.

REMEMBER: If floor is not carpeted, be sure to
place a heavy object at the base of the table half to
help prevent table half from sliding away from wall.

14. Pull legs #2 & #3 out from table and lock their hinges

by pulling hinges upward. (See detail in Figure 1,
previous page).

15. Put caps #13 on its ends of both legs #2 & #3. (See

Figure 5)

16. Rotate U-support #7 until you see the screw hole in

the slot of U-clip #6 (See Figure 5, Detail). Slide U­support #7 side to side if necessary.

17. Insert screw #19 through slot in U-clip #6 and into U-

support #7. Thread it all the way into U-support #7
until it touches the back of the tube. There should be
about 3/8 inch of screw #19 left sticking out. (See
Figure 5, Detail).

Figure 5

3