Escalade Sports 2L-6231-05 User Manual

OWNER'S
MANUAL

OAKWOOD

DROP POCKET

8 FT. HOME POOL

TABLE

MODEL NO.

P1001DG,808-1044-0018
P1021DG
P1006DG,883-0358-0018

READ THESE
INSTRUCTIONS
CAREFULLY!

For aid in identifying the different hardware used in this assembly, use the
hardware identifier on page 13. Each number refers to the numbers shown in the
illustrations within this manual. For more specific information about the hardware,
see the replacement parts list on page 12.

ASSEMBLY

OPERATION

SERVICE

WARRANTY

REPLACEMENT PARTS

INSTALLATION

2L-6231-05

1

OWNER'S

MANUAL

OWNER'S

MANUAL

OAKWOOD DROP POCKET

8 FT. SLATRON

HOME POOL TABLE

Thank you for buying our product. We try hard to insure that our products
are of high quality and free of problems, such as manufacturing defects or
missing parts. However, if you have any problems with your new product,
please DO NOT RETURN IT TO THE STORE. Call us at:

SERVICE

WARRANTY

TOLL FREE 1-800-426-1421

(THIS IS A CONSUMER ONLY NUMBER)

Or write us at:

CUSTOMER SERVICE DEPARTMENT

P.O. Box 889, Evansville, IN 47706

Please provide model number, serial number, and/or part number of the
product and/or part when you call or write. These numbers can be found on
the product, packaging, and/or in this Owner’s Manual.

ONE YEAR WARRANTY ON POOL TABLE

Manufacturer warrants to the original retail purchaser, this product to be free from
defects in material and workmanship for a period of one (1) year from the date of
purchase.

WARRANTY ON SURFACE

For seven (7) years from the date of purchase, we will repair the slatron surface of
this table, free of charge, if it fails to remain flat, within a tolerance of ± 30/1000 of
an inch, measuring from any flat plane within the playing surface. For ten (10) years
from the date of purchase, we will repair the slate surface of this table, free of charge,
if it fails to remain flat, within a tolerance of ± 20/1000 of an inch, measuring from
any flat plane within the playing surface. Note: Cloth not included in warranty.

Should this product become defective due to material or workmanship within the
warranty period, contact our Customer Service Department. This warranty is not
transferable and does not cover normal wear and tear, or damage caused by improper
handling, installation or use of this product. This warranty is also void if product is
in any way abused, damaged, or modified from its original state, or if used for other
than residential use. This warranty gives you specific legal rights, and you may have
other rights which vary from state to state.

Escalade Sports is a liscensee of Spalding

Trademark is owned by Lisco, Inc., a Spalding Company

2

IMPORTANT! READ THIS MANUAL
ALL THE WAY THROUGH BEFORE
BEGINNING TO PUT YOUR POOL

THE DRAWINGS IN THIS
MANUAL HAVE BEEN
EXAGGERATED OR MODI

TABLE TOGETHER! THEN READ

TO SHOW DETAILS.

EACH STEP BEFORE STARTING THAT
STEP.

This table has been inspected to insure proper fit. Carefully unpack and examine each shipping container and its
packing material before
discarding to assure all parts have been removed. Some smaller parts may be shipped inside
larger parts. Check inside parts before assembling.

This table is contained in three separate containers:

Container #1. . . . . . Three slate or slatron pieces

Container #2. . . . . . Contains this owner's manual, leg assemblies, hardware kits, corner & side caps,

corner posts, playfield spots, slate/slatron shims, glue and wood putty kit and drop pockets.

Container #3. . . . . . Contains long and short slats; beams, top rails; aprons; playfield cloth, and

additional hardware

Tools Needed ! Carpenter's level & 36'' Straight Edge

! 3/8" Open End Wrench ! Hammer (Small Ball Peen Type) ! Needle Nose Pliers
! 7/16" Open End Wrench ! Tape Measure ! Standard Screwdriver
! 1/2" Open End Wrench ! Sanding Block ! Phillips Screwdriver
! Putty Knife ! Power Screwdriver (optional BUT very ! Scissors or Sharp Knife
! Awl or 8d Nail helpful)

In addition to the assembly tools listed above, it would be useful to have a rachet with 3/8, 7/16 and 1/2 sockets
and an electric screwdriver.

NOTE: Rails are made with cushion rubber at a height that requires 2 ¼" diameter balls. Your dealer has a complete

line of Billiard Accessories.

NOTE: This table adds weight to any floor. Be sure floor can withstand this kind of weight. If floor sags, table will

be impossible to level!

THE SPRAY ADHESIVE USED FOR APPLYING PLAYFIELD CLOTH IS
EXTREMELY FLAMMABLE AND UNDER PRESSURE! CAREFULLY
READ CAUTIONS ON SPRAY ADHESIVE CONTAINER! KEEP OUT

OF REACH OF CHILDREN! DO NOT USE OR STORE NEAR HEAT
SOURCE, FLAMES, SP ARKS OR WHEN SMOKING! WORK AREA
MUST BE WELL VENTILATED. OPEN DOORS AND WINDOWS
WHEN USING SPRAY ADHESIVE.

3

Figure 1

1. Begin by opening hardware kit #1 (P/N 5A-6133-00).
Attach two wooden leg panels #2 to the inside of leg
facade #1 using six screws #33, six washers #35, and six
locknuts #34, per leg facade. Make sure that dimension
B (see illustration above) is at the bottom of the leg
panel. (Figure 1) NOTE: Leave all four bottom

screws #33 loose until the leg post #3 is installed.

2. Attach two leg posts #3 inside each metal leg facade
#1 using two carriage bolts #30, two washers #22,
and two locknuts #21 for each leg post in the leg
facade. Make sure that the two holes that are closer
together are at the top of the wooden posts. There
will be approximately 1/8 inch that will extend
below the metal facade. (Figure 2) Once the leg

post is securely fastened, tighten the four bottom
screws #33 on the leg panels.

Figure 2

NOTE: Leg post #3 CAN NOT be attached if the
four bottom screws #33 are tight. Tighten finger
tight only.

Figure 3

3. Now open the rail carton. Attach the wooden
beam #4 by using two long bolts #27, two short
bolts #40, six washers #23, and four locknuts
#26 as shown below. The two longer bolts #27
go in the top and bottom holes and the two
shorter #40 bolts go in the two outside holes.
Place a washer between the wooden leg and the
locknut on the two longer bolts #27. (Figure 3)

4

Figure 4

Detail A

Detail B

4. Now it is time to open hardware kit #2 (5A-6227-00). Place slats #5 and #6 across
table from beam to beam as shown in figure 4. Make sure to use the two shorter
slats #5 on the ends of the beams and the two longer slats #6 in the center as shown.
Insert four dowel connectors #39 into the holes in side of each of the beams #4
(See Figure 4 and Detail B), these holes should be closer to the top of the beams
#4. To attach slats #5 and #6 to the wooden beams #4, see the following procedure
noted: "Hint"

HINT: If the screwdriver slot in the dowel connector #39 is straight up and down, and you can see the threaded
bolt hole in the dowel connector #39 through the hole in the top of beam #4, the dowel connector #39 is lined
up. (See detail A) It is recommended to start the bolts by hand and not forcing them with power tools until you
are sure threads are engaged properly. After holes line up, insert screws #24 into slats and down into dowel
connectors (See detail B). Do not tighten completely yet.

5. Square up long slats #6 by measuring diagonally from end
to end as shown in figure 5. Check to make sure the table
is square. Then tighten screws into the dowel connectors.

Figure 5

5