ESAB TR-29 Two CyLinder Truck Kit Troubleshooting instruction

INSTRUCTIONS for

TR-29 TWO CYLINDER TRUCK KIT

Item No. 37924

for mounting:

353cv, 453cv, 653cvcc, MultiPower 460 and MultiPower 460 Pulse Power Sources

F15-592-B

March, 2003

This kit includes the following components:
1 — Assembled TR-29 Truck Body
1 — Cylinder Support
2 — Chain, 2/0 36" (not illustrated)
2 — Nuts 1/4" x 20 Lock
2 — Washer 1/4" Fender
4 — Screws 1/4"-20 1" Long

To mount Power Source on Truck, proceed as fol­lows:

1. Carefully lift the power source off the floor with a
crane or hoist and remove any skids from the base.

2. Lower the unit onto the truck base aligning the two
protruding screws on the rear bottom of the power
source (see photos above), with the U-slots pro­vided in the truck base. The rear slots are located
just in front of the wheel guards. Note also that all
protruding bolt heads on the bottom of the power
source have a hole drilled in the truck floor for them
to pass through. When the Power Source is prop­erly seated on the truck the weight of the unit is on
the floor of the truck not the side rails, and the front
floor of the truck will be flush with the lower front
panel of the Power Source.

4. The cylinder support is installed by first removing
the four corresponding (assembly screws) on the
top four corners of the power source. (See Figure 4
on reverse side.) Set the support on top of the power
source and install the longer screws provided. (Note)
If top does not lay flush, loosen screws on handle
and retighten after assembly .

(OPTIONAL)

- Install 1/4-20 Lock Nuts
on these screws once
assembled to the T ruck Kit.

Location of Screws
and U-Slots.

F15-592-B

Weight Bearing Area

Figure 1

3. If bolting the power source to the base, 2 screws
should protrude through the TR-29 Floor from the
base of the power source. Attach one .250 flat
washer and one .250 lock nut to each screw.

Be sure this information reaches the operator .
Y ou can get extra copies through your supplier .

Figure 2

This truck assembly is not intended to be hoisted
while attached in any way to a power source. If the
unit must be hoisted, the truck assembly must be
removed.

NEVER A TTEMPT TO LIFT A POWER SOURCE WITH
CYLINDER(S) A TTACHED!

5. Adjust cable strain relief bar to suitable height (see
Figure 3).

s

PRUDENCE

READ & UNDERSTA ND THIS LABEL
PROTECT YOURSELF AND OTHERS

LIRE & COMPRENDE CETTE ETIQUETTE

VOUS PROTEGER ET LES AUT R ES

6. To mount cylinders on completed assembly:
Slide at least the second link of each chain (678944)

into the center slot of the cylinder support.

Lifting eye to be used for lifting

Do NOT use when additional accessories

Cable Strain Relief Bar

power source ONLY.

are attached to power source.

L’oeil d’ascenseur etre utilise

pour la source de pouver seulement.

ont attachesa la source de pouvoir.

P/N 99512240-C 3/22/02

Floor of Truck is flush

with lower panel of

Power Source.

When you put the cylinders in place, pull the chain tightly
around each cylinder and slide a chain link into the outer
slot of the cylinder support. Be sure to pull the link down
firmly into each slot to secure the chain so that there is
little slack of the chain about the cylinder. DO NOT just
"loop" a link over the end of the support.

Cylinder support
assembly screws

Assembly Screws on
Left Side not visible.

Handle

F15-592-B 03 / 2003

Figure 3

Figure 4