INSTRUCTIONS for
F-9373-G
January, 1996
RV-27, RV-28, & RV-29
RELIEF VALVES
These INSTRUCTIONS are for experienced operators. If you are not fully familiar with the principles of operation and safe
practices for oxy-fuel gas equipment, we urge you to read our booklet Precautions and Safe Practices for Welding, Cutting,
and Heating, Form 2035. The same information appears in the Oxy-Acetylene Handbook which may be purchased from your
distributor. Do NOT permit untrained persons to operate this equipment. Do NOT attempt to operate this equipment until you
have read and fully understand these instructions. If you do not fully understand these instructions, contact your supplier for
further information.
Relief Valve Relief
Assembly Pressure Connection Dimensions
Setting
Model Part No. psig (BARS) Inlet Outlet
RV-27 11P62 15 (1.04)
RV-28 11P63 20 (1.38)
RV-29 11P64 23-75
(1.73-5.18)
3/4-in. 3/4-in. Height: 4-5/8-in. (118mm)
NPT NPT Width: 2-7/8-in. (73mm)
male female Diam: 1-7/8-in. (48mm)
These relief valves were originally designed for acetylene and fuel gas equipment. It can be used for any noncorrosive, non-toxic industrial gas.
The following instructions and repairs are intended for
experienced personnel only. Do not permit untrained
persons to inspect, clean, or repair this apparatus. Use
only recommended replacement parts or send the apparatus to your distributor for repairs. Improperly repaired
apparatus is hazardous.
GENERAL MAINTENANCE
1. Periodically, lift the lever on the side of the relief valve
slowly and release gas only for an instant. Allow the
valve to close on its own spring force. This will operate properly in case of excess pressure.
2. Check all joints and connections for leakages periodically with Leak Test Solution, P/N 998771 (8 oz.
container), or any other solution suitable for oxygen
service. Also apply a film of the leak solution over
the opening of the outlet. Bubbling of the solution
will indicate leakage. Do not continue operating until leakage is corrected. If leakage was noted around
valve joints or at the outlet, the O-rings in the relief
valve should be replaced.
DISASSEMBLY
Shut off gas supply by closing valve upstream of relief
valve and then release trapped pressure by opening
downstream valve or by lifting relief valve lever. The relief valve can be disassembled by leaving it mounted to
the equipment if desired.
To disassemble, do the following:
1. Insert a piece of 3/32-in. drill rod into the hole in the
cap and then rotate the pressure-adjusting cap three
or four times in a counterclockwise direction to reduce spring force on the poppet.
2. Unscrew the bonnet assembly from the body and, if
necessary, remove the spring from the bonnet The
spring can be spiraled out by turning it from the bottom, counterclockwise.
3. Lift out the poppet, being careful not to lose the
spacer which rests inside it.
4. Remove the operating lever by first removing the
screw and washer which hold it in position and then
sliding the lever off the lifting shaft.
5. Remove the lifting shaft by first removing the screw
and washer which hold it in position and then sliding
the shaft out of the relief valve body.
CLEANING AND INSPECTION
1. If parts are dirty from foreign matter in the gas
stream, they should be cleaned by using a clean
damp cloth. Replace any metal parts that appear
heavily marred or damaged particularly in areas that
contact the O-rings.
2. O-rings should be replaced periodically or whenever
the valve is disassembled. After removing the old
O-rings, make sure the grooves are clean. Lubricate the lever shaft O-ring and the upper poppet Oring (70S05 and 70S03) lightly with Dow-Corning
Compound No. 111 (77500101) before installing. DO
NOT lubricate the lower poppet O-ring (70S04).
Be sure this information reaches the operator.
You can get extra copies through your supplier..
REASSEMBLY
1. Insert the shaft into the body with the flat section
facing towards the poppet. Be sure the O-ring is in
place on the shaft. Secure the shaft in place with
the No. 4 screw and washer.
2. Install the operating lever in any position and secure it to the shaft with the No. 6 screw and washer.
3. Insert the spacer in the poppet and then place the
poppet in the body so that the lower O-ring is resting on the seat.
4. Install the spring in the bonnet. Turn it a few times
until the bonnet can be placed on the body without
too much spring pressure against the poppet.
5. With O-ring properly positioned above the threads
of the bonnet, assemble the bonnet to the body and
tighten snugly with a wrench.
2. Turn the relief valve pressure-adjusting cap until the
valve just starts to relieve.
3. Back out pressure-adjusting screw on the regulator
supplying the air or nitrogen about one turn. Relieve
the pressure by lifting the lever on the relief valve.
4. Turn in the regulator pressure-adjusting screw slowly
to make sure the valve relieves at the proper pressure.
ALTERNATE RESETTING METHOD
(RV-27 and RV-28)
If the relief valve assembly was not removed from acetylene equipment such as hydraulic back pressure valves
and since acetylene pipeline pressure should not exceed 15 psi, the RV-27 and RV-28 can be reset as follows:
RESETTING THE RELIEF VALVE
Ideally, with proper test set up, using dry air or nitrogen,
and a suitable gas regulator, the regulator, the relief valve
can be set as follows:
1. Adjust pressure on the inlet side of the relief valve
to the proper relief pressure as follows:
RV-27: 15 psi (1.04 BARS)
RV-28: 20 psi (1.35 BARS)
RV-29: Any pressure 1-1/4 to 3 times the normal
operating pressure but no less than 25 psi (1.73
BARS) nor more than 75 psi (5.18 BARS).
BONNET ASSY. - 23R86
(2) PIN - 70S02
O-RING - 86W84
SPACER - 7280-0040
1. With downstream valve closed, open upstream valve
and adjust the regulator to supply 13 psig of acetylene.
2. Turn the relief valve pressure-adjusting cap until
acetylene starts to relieve.
3. Recheck the setting by backing out the regulator
pressure-adjusting screw about one turn, release
the trapped pressure by lifting relief valve lever; and
then slowly increase the supply pressure back to
make sure the valve relieves at 13 psi.
4. Turn the relief valve pressure-adjusting cap 1/2 turn
clockwise on the RV-27, which will set the relief pressure at 15 psi; 2 turns clockwise on the RV-28 for
the 20 psi setting.
PRESSURE-ADJUSTING CAP
(Part of 23R86)
SPRING
O-RING - 70S03*
SCREW - No. 4-40 x 3/16"
WASHER - No. 4
66S23 (RV-27 & RV-28)
66S22 (RV-29)
SPRING
66S20 (RV-27 & RV-28)
66S19 (RV-29)
O-RING - 70S04
SHAFT - 66S18
Included with RV REPAIR KIT - 2119746
Fig. 1 - Relief Valve Assembly
F-9373-G 1/96 1M Printed in U.S.A.
SCREW - No. 6-32 x 1/4"
WASHER - No. 6
LEVER - 66S17
* O-RING - 70S05
RV-27 (11P62) 15 psi (1.04 BARS)
RV-28 (11P63) 20 psi (1.38 BARS)
RV-29 (11P64) 75 psi (5.8 BARS)
Loading...