PT-36 G2 Plasma System Cutting Data - ICH
Cut Data Manual (EN)
0558011510 Version 4.7 released on 26Mar15
METRIC
BE SURE THIS INFORMATION REACHES THE OPERATOR.
YOU CAN GET EXTRA COPIES THROUGH YOUR SUPPLIER.
CAUTION
These INSTRUCTIONS are for experienced operators. If you are not fully familiar with the
principles of operation and safe practices for arc welding and cutting equipment, we urge
you to read our booklet, “Precautions and Safe Practices for Arc Welding, Cutting, and
Gouging,” Form 52-529. Do NOT permit untrained persons to install, operate, or maintain
this equipment. Do NOT attempt to install or operate this equipment until you have read
and fully understand these instructions. If you do not fully understand these instructions,
contact your supplier for further information. Be sure to read the Safety Precautions before installing or operating this equipment.
USER RESPONSIBILITY
This equipment will perform in conformity with the description thereof contained in this manual and accompanying labels and/or inserts when installed, operated, maintained and repaired in accordance with the instructions provided. This equipment must be checked periodically. Malfunctioning or poorly maintained equipment
should not be used. Parts that are broken, missing, worn, distorted or contaminated should be replaced immediately. Should such repair or replacement become necessary, the manufacturer recommends that a telephone
or written request for service advice be made to the Authorized Distributor from whom it was purchased.
This equipment or any of its parts should not be altered without the prior written approval of the manufacturer.
The user of this equipment shall have the sole responsibility for any malfunction which results from improper
use, faulty maintenance, damage, improper repair or alteration by anyone other than the manufacturer or a service facility designated by the manufacturer.
READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.
PROTECT YOURSELF AND OTHERS!
2
TABLE OF CONTENTS
SUBSECTION TITLE ............................................................................PAGE
Safety Precautions..........................................................................................5
Carbon Steel Quality.......................................................................................13
Aluminum Quality .........................................................................................35
Stainless Steel Quality......................................................................................47
Carbon Steel Production ...................................................................................61
Aluminum Production .................................................................................... 83
Stainless Steel Production................................................................................. 95
Water Injection Aluminum Production.....................................................................117
Water Injection Stainless Steel Production ................................................................ 127
Carbon Steel Air ..........................................................................................141
Aluminum Air ........................................................................................... 155
Stainless Steel Air ........................................................................................ 161
3
TABLE OF CONTENTS
4
SAFETY PRECAUTIONS
Safety Precautions Safety - English
WARNING: These Safety Precautions are for your
protection. They summarize precautionary information from the references
listed in Additional Safety Information
section. Before performing any installation or operating procedures, be sure to read and
follow the safety precautions listed below as well
as all other manuals, material safety data sheets,
labels, etc. Failure to observe Safety Precautions
can result in injury or death.
PROTECT YOURSELF AND OTHERS -Some welding, cutting, and gouging
processes are noisy and require ear
protection. The arc, like the sun, e mits
ultraviolet (UV) and other radiation
and can injure skin and eyes. Hot metal can cause
burns. Training in the proper use of the processes
and equipment is essential to prevent accidents.
Therefore:
1. Always wear safety glasses with side shields in
any work area, even if welding helmets, face
shields, and goggles are also required.
2. Use a face shield tted with the correct lter and
cover plates to protect your eyes, face, neck, and
ears from sparks and rays of the arc when operating or observing operations. Warn bystanders
not to watch the arc and not to expose themselves
to the rays of the electric-arc or hot metal.
3. Wear ameproof gauntlet type gloves, heavy
long-sleeve shirt, cuess trousers, high -topped
shoes, and a welding helmet or cap for hair
protection, to protect against arc rays and hot
sparks or hot metal. A ameproo f apron may also
be desirable as protection against radiated heat
and sparks.
4. Hot sparks or me tal can lodge in rolled up sleeves,
trouser cus, or pockets. Sleeves and collars
should be kept buttoned, and open pockets
eliminated from the front of clothing.
5. Protect other personnel from arc rays and hot
sparks with a suitable non-ammable partition
or curtains.
6. Use goggles over safety glasses when chipping
slag or grinding. Chipped slag may be hot and
can y far. Bystanders should also wear goggles
over safety glasses.
1. Remove all combustible materials well away from
the work area or cover the materials with a protective non-ammable covering. Combustible
materials include wood, cloth, sawdust, liquid
and gas fuels, solvents, paints and coatings,
paper, etc.
2. Hot sparks or hot metal can fall through cracks
or crevices in oors or wall openings and cause a
hidden smoldering re or res on the oor below.
Make certain that such openings are protected
from hot sparks and metal.“
3. Do not weld, cut or perform other hot work until
the work piece has been completely cleaned so
that there are no substances on the work piece
which might produce ammable or toxic vapors.
Do not do hot work on closed containers. They
may explode.
4. Have re extinguishing equipment handy for
instant use, such as a garden hose, water pail,
sand bucket, or portable re extinguisher. Be
sure you are trained in its use.
5. Do not use equipment beyond its ratings. For
example, overloaded welding cable can overheat
and create a re hazard.
6. After completing operations, inspect the work
area to make certain there are no hot sparks or
hot metal which could cause a later re. Use re
watchers when necessary.
7. For additional information, refer to NFPA Standard 51B, "Fire Prevention in Use of Cutting and
Welding Processes", available from the National
Fire Protection Association, Batter y march Park,
Quincy, MA 02269.
areas, if movement is conned, or if there is danger
of falling.
FIRES AND EXPLOSIONS -- Heat from
ames and arcs can start res. Hot
slag or sparks can also cause res and
explosions. Therefore:
ELECTRICAL SHOCK -- Contact with
live electrical parts and ground can
cause severe injury or death. DO
NOT use AC welding current in damp
5
SAFETY PRECAUTIONS
1. Be sure the power source frame (chassis) is connected to the ground system of the input power.
2. Connect the work piece to a good electrical
ground.
3. Connect the work cable to the work piece. A poor
or missing connection can expose you or others
to a fatal shock.
4. Use well-maintained equipment. Replace worn or
damaged cables.
5. Keep everything dry, including clothing, work
area, cables, torch/electrode holder, and power
source.
6. Make sure that all parts of your body are insulated
from work and from ground.
7. Do not stand directly on metal or the earth while
working in tight quarters or a damp area; stand
on dry boards or an insulating platform and wear
rubber-soled shoes.
8. Put on dry, hole-free gloves before turning on the
power.
3. Welders should use the following procedures to
minimize exposure to EMF:
A. Route the electrode and work cables together.
Secure them with tape when possible.
B. Never coil the torch or work cable around your
body.
C. Do not place your body between the torch and
work cables. Route cables on the same side of
your body.
D. Connect the work cable to the work piece as close
as possible to the area being welded.
E. Keep welding power source and cables as far
away from your body as possible.
FUMES AND GASES -- Fumes and
gases, can cause discomfort or harm,
particularly in conned spaces. Do
not breathe fumes and gases. Shielding gases can cause asphyxiation.
Therefore:
9. Turn o the power before removing your gloves.
10. Refer to ANSI/ASC Standard Z49.1 (listed on
next page) for specic grounding recommendations. Do not mistake the work lead for a ground
cable.
ELECTRIC AND MAGNETIC FIELDS
— May be dangerous. Electric current owing through any conductor causes localized Electric and
Magnetic Fields (EMF). Welding and
cutting current creates EMF around welding cables
and welding machines. Therefore:
1. Welders having pacemakers should consult their
physician before welding. EMF may interfere with
some pacemakers.
2. Exposure to EMF may have other health eects which
are unknown.
1. Always provide adequate ventilation in the work area
by natural or mechanical means. Do not weld, cut, or
gouge on materials such as galvanized steel, stainless steel, copper, zinc, lead, beryllium, or cadmium
unless positive mechanical ventilation is provided.
Do not breathe fumes from these materials.
2. Do not operate near degreasing and spraying operations. The heat or arc rays can react with chlorinated
hydrocarbon vapors to form phosgene, a highly
toxic gas, and other irritant gases.
3. If you develop momentary eye, nose, or throat irritation while operating, this is an indication that
ventilation is not adequate. Stop work and take
necessary steps to improve ventilation in the work
area. Do not continue to operate if physical discomfort persists.
4. Refer to ANSI/ASC Standard Z49.1 (see listing below)
for specic ventilation recommendations.
6
SAFETY PRECAUTIONS
5. WARNING: This product, when used for welding
or cutting, produces fumes or gases
which contain chemicals known to
the State of California to cause birth
defects and, in some cases, cancer.
(California Health & Safety Code
§25249.5 et seq.)
CYLINDER HANDLING -- Cylinders,
if mishandled, can rupture and violently release gas. Sudden rupture
of cylinder, valve, or relief device can
injure or kill. Therefore:
1. Use the proper gas for the process and use the
proper pressure reducing regulator designed to
operate from the compressed gas cylinder. Do not
use adaptors. Maintain hoses and ttings in good
condition. Follow manufacturer's operating instructions for mounting regulator to a compressed gas
cylinder.
1. Always have qualied personnel perform the installation, troubleshooting, and maintenance work.
Do not perform any electrical work unless you are
qualied to perform such work.
2. Before performing any maintenance work inside a
power source, disconnect the power source from
the incoming electrical power.
3. Maintain cables, grounding wire, connections, power
cord, and power supply in safe working order. Do
not operate any equipment in faulty condition.
4. Do not abuse any equipment or accessories. Keep
equipment away from heat sources such as furnaces,
wet conditions such as water puddles, oil or grease,
corrosive atmospheres and inclement weather.
5. Keep all safety devices and cabinet covers in position
and in good repair.
6. Use equipment only for its intended purpose. Do
not modify it in any manner.
2. Always secure cylinders in an upright position by
chain or strap to suitable hand trucks, undercarriages, benches, walls, post, or racks. Never secure
cylinders to work tables or xtures where they may
become part of an electrical circuit.
3. When not in use, keep cylinder valves closed. Have
valve protection cap in place if regulator is not connected. Secure and move cylinders by using suitable
hand trucks. Avoid rough handling of cylinders.
4. Locate cylinders away from heat, sparks, and ames.
Never strike an arc on a cylinder.
5. For additional information, refer to CGA Standard P-1,
"Precautions for Safe Handling of Compressed Gases
in Cylinders", which is available from Compressed
Gas Association, 1235 Jeerson Davis Highway,
Arlington, VA 22202.
EQUIPMENT MAINTENANCE -- Faulty or
improperly maintained equipment can
cause injury or death. Therefore:
ADDITIONAL SAFETY INFORMATION -- For
more information on safe practices for
electric arc welding and cutting equipment, ask your supplier for a copy of
"Precautions and Safe Practices for Arc
Welding, Cutting and Gouging", Form
52-529.
The following publications, which are available from
the American Welding Society, 550 N.W. LeJuene Road,
Miami, FL 33126, are recommended to you:
1. ANSI/ASC Z49.1 - "Safety in Welding and Cutting"
2. AWS C5.1 - "Recommended Practices for Plasma Arc
Welding"
3. AWS C5.2 - "Recommended Practices for Plasma Arc
Cutting"
4. AWS C5.3 - "Recommended Practices for Air Carbon
Arc Gouging and Cutting"
7
SAFETY PRECAUTIONS
5. AWS C5.5 - "Recommended Practices for Gas Tungsten Arc Welding“
6. AWS C5.6 - "Recommended Practices for Gas Metal
Arc Welding"“
7. AWS SP - "Safe Practices" - Reprint, Welding Handbook.
8. ANSI/AWS F4.1, "Recommended Safe Practices for
Welding and Cutting of Containers That Have Held
Hazardous Substances."
MEANING OF SYMBOLS - As used
throughout this manual: Means Attention! Be Alert! Your safety is involved.
Means immediate hazards which,
if not avoided, will result in immediate, serious personal injury
or loss of life.
Means potential hazards which
could result in personal injury or
loss of life.
Means hazards which could result
in minor personal injury.
8
SAFETY PRECAUTIONS
Hydrogen explosion hazard! Read the following before attempting
DANGER
A hazard exists whenever a water table is used with plasma arc cutting. Severe explosions have resulted from the accumulation of hydrogen beneath the plate being cut. Thousands of dollars in property damage have been caused by
these explosions. Personal injury or death could result from such an explosion.
The best available information indicates that three possible sources of hydrogen exists in water tables:
1. Molten Metal Reaction
Most of the hydrogen is liberated by a fast reaction of molten metal from the kerf in the water to form metallic ox-
ides. This reaction explains why reactive metals with greater anity for oxygen, such as aluminum and magnesium,
release greater volumes of hydrogen during the cut than does iron or steel. Most of this hydrogen will come to the
surface immediately, but some will cling to small metallic particles. These particles will settle to the bottom of the
water table and the hydrogen will gradually bubble to the surface.
2. Slow Chemical Reaction
Hydrogen may also result from the slower chemical reactions of cold metal particles with the water, dissimilar metals,
or chemicals in the water. The hydrogen gradually bubbles to the surface.
to cut when using a water table.
3. Plasma & Shield Gas
Hydrogen or other fuel gases, such as Methane (CH4), may come from the plasma or shield gas. H-35 is a commonly
used plasma gas. This gas is 35% hydrogen by volume. When using H-35 at high currents, as much as 125 cfh of
hydrogen will be released.
Regardless of the source, the hydrogen gas can collect in pockets formed by the plate being cut and slats on the
table, or pockets from warped plate. There can also be accumulation of hydrogen under the slag tray or even in the
air reservoir, if these are part of the table design. The hydrogen, in the presence of oxygen or air, can then be ignited
by the plasma arc or a spark from any source.
4. Follow these practices to reduce hydrogen generation and accumulation:
A. Clean the slag (especially ne particles) from the bottom of the table frequently. Rell the table with clean water.
B. Do not leave plates on the table overnight or a weekend.
C. If a water table has been unused for several hours, vibrate it in some way before the rst plate is laid in position.
This will allow accumulated hydrogen in the refuse to break loose and dissipate before it is conned by a plate
on the table. This might be accomplished by laying the rst plate onto the table with a slight jolt, then raising
the plate to permit hydrogen to escape before it is nally set down for cutting.
D. If cutting above water, install fans to circulate air between the plate and the water surface.
E. If cutting underwater, agitate the water under the plate to prevent accumulation of hydrogen. This can be done
by aerating the water using compressed air.
F. If possible, change the level of the water between cuts to dissipate accumulated hydrogen.
G. Maintain pH level of the water near 7 (neutral). This reduces the rate of chemical reaction between water and
metals.
9
SAFETY PRECAUTIONS
Possible explosion hazard from plasma cutting aluminum-lithium alloys!
Aluminum-Lithium (Al-Li) alloys are used in the aerospace industry because of 10% weight
savings over conventional aluminum alloys. It has been reported that molten Al-Li alloys
can cause explosions when they come into contact with water. Therefore, plasma cutting
of these alloys should not be attempted in the presence of water. These alloys should only
be dry cut on a dry table. Alcoa has determined that "dry" cutting on a dry table is safe
and gives good cutting results. DO NOT dry cut over water. DO NOT water injection cut.
WARNING
The following are some of the Al-Li alloys currently available:
Alithlite (Alcoa) X8192 (Alcoa)
Alithally (Alcoa) Navalite (U. S. Navy)
2090 Alloy (Alcoa) Lockalite (Lockhead)
X8090A (Alcoa) Kalite (Kaiser)
X8092 (Alcoa) 8091 (Alcan)
For additional details and information on the safe use from the hazards associated with
these alloys, contact your aluminum supplier.
WARNING
WARNING
WARNING
Oil And Grease Can Burn Violently!
• Never use oil or grease on this torch.
• Handle torch clean hands only on clean surface.
• Use silicone lubricant only where directed.
• Oil and grease are easily ignited and burn violently in the presence of
oxygen under pressure.
Hydrogen explosion hazard.
Do Not Cut Underwater With H-35! Dangerous buildup of hydrogen gas is possible in
the water table. Hydrogen gas is extremely explosive. Reduce the water level to 4 inches minimum below the workpiece. Vibrate plate, stir air and water frequently to prevent
hydrogen gas buildup.
Spark hazard.
Heat, spatter, and sparks cause re and burns.
• Do not cut near combustible material.
• Do not cut containers that have held combustibles.
• Do not have on your person any combustibles (e.g. butane lighter).
• Pilot arc can cause burns. Keep torch nozzle away from yourself and
others when activating plasma process.
• Wear correct eye and body protection.
• Wear gauntlet gloves, safety shoes and hat.
• Wear ame-retardant clothing that covers all exposed areas.
• Wear cuess trousers to prevent entry of sparks and slag.
10
SAFETY PRECAUTIONS
Maximum Gas Flow Rates With PT-36 Torch
Gas &
Pressure
Air (85psi / 5.9bar)
Process
Air (85psi / 5.9bar)
Air Curtain
Argon
(125psi / 8.6bar)
CH-4
(75psi / 5.2bar)
H-35 / F5
(75psi / 5.2bar)
Nitrogen
(125psi / 8.6bar)
Oxygen
(125psi / 8.6bar)
Maximum Gas Flow Rates - CFH (CMH)
With PT-36 Torch
EPP-201 EPP-360 EPP-450 EPP-601
269
(7.6)
120 0
(34)
100
(2.8)
85
(2.4)
95
(2.7)
385
(10.9)
66
(1.9)
Note: No marking with the 600 ampere nozzle.
269
(7.6)
120 0
(34)
100
(2.8)
85
(2.4)
202
(5.7)
496
(14. 0)
190
(5.4)
474
(13. 4)
120 0
(34)
100
(2.8)
85
(2.4)
202
(5.7)
496
(14. 0)
295
(8.4)
474
(13. 4)
120 0
(34)
100
(2.8)
85
(2.4)
254
(7.2)
496
(14. 0)
295
(8.4)
Gas Purity
Filtered to 25 microns
DIN Quality ISO 8573-1
Oil Quality mg/m3 = 0.1 Class 2
Particle Size 0.1µm Class 1
Temperature +3°C Class 4
Clean, Dry, Oil Free
Filtered to 25 microns
99.995%, Filtered to 25 microns
93%, Filtered to 25 microns
99.995%, Filtered to 25 microns
99.99%, Filtered to 25 microns
99.5%, Filtered to 25 microns
The m3 cut data was gathered using the following materials:
Aluminum: 6061,Al-Mg1SiCu,AlMg1SiCu,3.3211
Carbon Steel: AISI 1008, ASTM A572 Gr.50, ASTM A36
Stainless Steel: 304, 1.4301 CrNi DIN 17440 X5CrNi18-10 DIN EN 10088
***Materials with dierent compositions and properties may require adjustment of the pub-
lished cutting parameters to achieve optimal results.***
11
12
Carbon Steel
Quality
13
14
M MS 30A GS6 ncode109 pic36
MARKING
Amperes 30
Cut Gas ARG
Start Gas ARG
Shield Gas-1 AIR
Shield Gas-2 NONE
Material Carbon Steel
Gas Select 6
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
70
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
5.2
5.2
0.0
0.0
2.0
2.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
15
121212730
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.100)
0.35
3
3(0.100)
3(0.100)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
Q MS 30A GS1 ncode109 pic36
QUALIT Y
Amperes 30
Start Gas N2
Cut Gas O2
Shield Gas-1 N2
Shield Gas-2 O2
Material Carbon Steel
Gas Select 1
Code Description
ESAB Welding and Cutting Products
1 1 1 1 1
4.8 4.8 4.8 4.8 4.8
0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0
4.5 4.5 4.5 4.5 4.5
0.0 0.6 0.6 0.7 0.7
0.0 0.6 0.6 0.7 0.7
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
16
0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
30 30 30 30 30
P10 Start Current - Amps
30 30 30 30 30
P11 Cut Current - Amps
15 15 15 15 15
P12 End Current - Amps
30 30 30 30 30
P13 Corner Current - Amps
30 30 30 30 30
P14 Pilot Arc Current - Amps
0.1 0.1 0.1 0.1 0.1
0.4 0.5 0.5 0.5 0.5
0.0 0.0 0.0 0.0 0.0
0.1 0.1 0.1 0.1 0.1
1.0 1.0 1.0 1.0 1.0
(0.130) 3(0.130) 4(0.150) 4(0.150) 4(0.150)
0.10 0.10 0.10 0.10 0.10
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
4(0.157) 4(0.157) 4(0.157) 4(0.157) 5(0.197)
3(0.130) 3(0.114) 3(0.126) 3(0.135) 4(0.145)
3
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
1(0.040) 2(0.080) 3(0.125) 4(0.160) 5(0.188)
H4 Thickness - mm(inch)
110 110 112 11 5 120
H5 Arc Voltage - Volts
(150) 1400(55) 1070(42) 930(37) 760(30)
1.7(0.065) 1.7(0.065) 1.7(0.065) 1.7(0.067) 1.8(0.070)
3810
(inch/min)
Speed - mm/min
Kerf - mm(inch)
M MS 45A GS6 ncode101 pic17
MARKING
Material Carbon Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 45
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
85
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
5.2
5.2
0.0
0.0
2.0
2.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
17
141414730
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
4(0.160)
4(0.160)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
Q MS 45A GS1 ncode101 pic17
QUALIT Y
Material Carbon Steel
Gas Select 1
Cut Gas O2
Start Gas N2
Amperes 45
Shield Gas-1 N2
Shield Gas-2 O2
Code Description
ESAB Welding and Cutting Products
1 1 1
3.5 3.5 3.5
0.0 0.0 0.0
0.0 0.0 0.0
4.5 4.0 4.0
0.0 0.0 0.0
0.0 0.0 0.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
18
0.0 0.0 0.0
0.0 0.0 0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
50 50 50
P10 Start Current - Amps
45 45 45
P11 Cut Current - Amps
50 50 50
P12 End Current - Amps
45 45 45
P13 Corner Current - Amps
30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6
0.2 0.3 0.3
0.0 0.0 0.0
0.6 0.6 0.6
1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
4(0.157) 4(0.157) 5(0.197)
3(0.120) 3(0.125) 5(0.180)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
1(0.040) 2(0.080) 3(0.125)
H4 Thickness - mm(inch)
123 131 134
H5 Arc Voltage - Volts
(150) 1980(78) 1650(65)
2.3(0.090) 3.0(0.120) 2.8(0.110)
3810
(inch/min)
Speed - mm/min
Kerf - mm(inch)
M MS 55A GS6 ncode102 pic17
MARKING
Material Carbon Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 55
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
85
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
5.2
5.2
0.0
0.0
2.0
2.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
19
141414730
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
4(0.160)
4(0.160)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
Q MS 55A GS1 ncode102 pic17
QUALIT Y
Material Carbon Steel
Gas Select 1
Cut Gas O2
Start Gas N2
Amperes 55
Shield Gas-1 N2
Shield Gas-2 O2
Code Description
ESAB Welding and Cutting Products
1 1 1 1
3.5 3.5 3.5 3.5
0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0
4.0 4.0 4.1 4.1
0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
20
0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
50 50 50 50
P10 Start Current - Amps
55 55 55 55
P11 Cut Current - Amps
50 50 50 50
P12 End Current - Amps
55 55 55 55
P13 Corner Current - Amps
30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6
0.3 0.3 0.3 0.3
0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
5(0.197) 6(0.236) 5(0.197) 5(0.197)
5(0.200) 6(0.240) 5(0.200) 5(0.200)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
3(0.125) 4(0.160) 5(0.188) 6(0.250)
H4 Thickness - mm(inch)
122 127 132 137
H5 Arc Voltage - Volts
(118) 2160(85) 1400(55) 1020(40)
2.5(0.100) 2.5(0.100) 2.5(0.100) 3.0(0.120)
3000
(inch/min)
Speed - mm/min
Kerf - mm(inch)
M MS 60A GS6 ncode110 pic37
MARKING
Amperes 60
Cut Gas ARG
Start Gas ARG
Shield Gas-1 AIR
Shield Gas-2 NONE
Material Carbon Steel
Gas Select 6
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
75
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
5.2
5.2
0.0
0.0
2.0
2.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
21
121212730
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
3(0.100)
3(0.100)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
Q MS 60A GS1 ncode110 pic37
QUALIT Y
Amperes 60
Start Gas N2
Cut Gas O2
Shield Gas-1 N2
Shield Gas-2 O2
Material Carbon Steel
Gas Select 1
Code Description
ESAB Welding and Cutting Products
1 1 1 1 1
4.1 4.1 4.1 4.1 4.1
0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0
4.5 4.5 4.5 4.5 4.5
1.0 1.0 1.0 1.0 1.0
1.4 1.4 1.4 1.4 1.4
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
22
1.0 1.0 1.0 1.0 1.0
1.0 1.0 1.0 1.0 1.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
45 45 45 45 45
P10 Start Current - Amps
60 60 60 60 60
P11 Cut Current - Amps
13 13 13 12 12
P12 End Current - Amps
60 60 60 60 60
P13 Corner Current - Amps
30 30 30 30 30
P14 Pilot Arc Current - Amps
0.3 0.4 0.6 0.6 0.6
0.6 0.6 0.6 1.0 1.0
0.0 0.0 0.0 0.0 0.0
0.1 0.1 0.1 0.1 0.1
1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.10 0.10 0.10 0.10 0.10
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
4(0.157) 4(0.157) 4(0.157) 4(0.157) 4(0.157)
3(0.120) 3(0.116) 3(0.110) 3(0.100) 3(0.100)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
3(0.125) 4(0.160) 5(0.188) 6(0.250) 8(0.313)
H4 Thickness - mm(inch)
105 105 105 105 105
H5 Arc Voltage - Volts
(163) 3480(137) 2640(104) 2180(86) 1750(69)
1.5(0.060) 1.5(0.060) 1.5(0.060) 1.7(0.065) 1.7(0.065)
4140
(inch/min)
Speed - mm/min
Kerf - mm(inch)
M MS 100A GS6 ncode103 pic2
MARKING
Material Carbon Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 100
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
90
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
3.6
3.6
0.0
0.0
2.0
2.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
23
121212730
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
4(0.160)
4(0.160)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
Q MS 100A GS1 ncode103 pic2
QUALIT Y
Material Carbon Steel
Gas Select 1
Cut Gas O2
Start Gas N2
Amperes 100
Shield Gas-1 N2
Shield Gas-2 O2
Code Description
ESAB Welding and Cutting Products
1 1 1 1 1 1
1.7 1.7 1.7 1.7 1.7 1.7
0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0
4.1 4.1 4.1 4.1 4.1 4.1
2.8 2.8 2.8 2.8 2.8 2.8
2.8 2.8 2.8 2.8 2.8 2.8
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
24
0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
50 50 50 50 50 50
P10 Start Current - Amps
100 100 100 100 100 100
P11 Cut Current - Amps
50 50 50 50 50 50
P12 End Current - Amps
100 100 100 100 100 100
P13 Corner Current - Amps
30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6
0.1 0.3 0.4 0.4 0.4 0.6
0.0 0.0 0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
4(0.157) 4(0.157) 4(0.157) 4(0.157) 5(0.197) 6(0.236)
3(0.100) 3(0.100) 3(0.100) 3(0.100) 3(0.100) 3(0.100)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
4(0.160) 5(0.188) 6(0.250) 8(0.313) 10(0.375) 12(0.500)
H4 Thickness - mm(inch)
135 135 135 138 138 141
H5 Arc Voltage - Volts
(95) 2310(91) 2290(90) 2010(79) 1780(70) 1600(63)
2410
2.0(0.080) 2.0(0.080) 2.0(0.080) 2.0(0.080) 2.0(0.080) 2.3(0.090)
(inch/min)
Speed - mm/min
Kerf - mm(inch)
M MS 130A GS6 ncode104 pic29
MARKING
Material Carbon Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 130
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
80
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
3.6
3.6
0.0
0.0
2.0
2.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
25
121212730
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
4(0.160)
4(0.160)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
Q MS 130A GS1 ncode104 pic29
QUALIT Y
Material Carbon Steel
Gas Select 1
Cut Gas O2
Start Gas N2
Amperes 130
Shield Gas-1 N2
Shield Gas-2 O2
Code Description
ESAB Welding and Cutting Products
1 1 1 1 1 1 1
1.7 1.7 1.7 1.7 1.7 1.7 1.7
0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0
3.5 3.5 3.5 3.5 3.5 3.5 3.5
3.4 3.4 1.7 1.7 4.5 4.5 4.5
3.4 3.4 1.7 1.7 4.5 4.5 4.5
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
26
0.0 0.0 1.7 2.8 0.0 0.0 0.0
0.0 0.0 2.3 2.8 0.0 0.0 0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
60 60 60 60 60 60 60
P10 Start Current - Amps
130 130 130 130 130 130 130
P11 Cut Current - Amps
60 60 60 60 60 60 60
P12 End Current - Amps
130 130 130 130 130 130 130
P13 Corner Current - Amps
30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6
0.5 0.5 0.5 0.6 0.6 0.6 0.6
0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
4(0.157) 4(0.157) 4(0.157) 5(0.197) 6(0.236) 8(0.315) 8(0.315)
3(0.120) 3(0.130) 3(0.116) 3(0.130) 5(0.180) 4(0.170) 4(0.150)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
5(0.188) 6(0.250) 8(0.313) 10(0.375) 12(0.500) 15(0.600) 16(0.625)
H4 Thickness - mm(inch)
123 125 129 132 136 138 140
H5 Arc Voltage - Volts
(105) 2540(100) 2340(92) 2160(85) 1910(75) 1470(58) 1300(51)
2.4(0.095) 2.4(0.095) 2.4(0.095) 2.4(0.095) 2.4(0.095) 2.5(0.099) 2.5(0.100)
2670
(inch/min)
Speed - mm/min
Kerf - mm(inch)
M MS 200A GS6 ncode105 pic3
MARKING
Material Carbon Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 200
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
70
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
2.8
2.8
0.0
0.0
2.0
2.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
27
121414730
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
4(0.160)
4(0.160)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
Q MS 200A GS1 ncode105 pic3
QUALIT Y
Material Carbon Steel
Gas Select 1
Cut Gas O2
Start Gas N2
Amperes 200
Shield Gas-1 N2
Shield Gas-2 O2
Code Description
ESAB Welding and Cutting Products
10(0.375) 12(0.500) 15(0.600) 16(0.625) 20(0.750) 22(0.875) 25(1.000) 30(1.180) 32(1.250)
H4 Thickness - mm(inch)
130 130 130 131 135 137 139 144 147
H5 Arc Voltage - Volts
(86) 2110(83) 1880(74) 1780(70) 1520(60) 1270(50) 1020(40) 810(32) 690(27)
2180
3.0(0.120) 3.0(0.120) 3.0(0.120) 3.0(0.120) 3.0(0.120) 3.0(0.120) 3.0(0.120) 3.6(0.142) 3.8(0.150)
(inch/min)
Speed - mm/min
Kerf - mm(inch)
1 1 1 1 1 1 1 1 1
1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2 1.2
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2
3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1
3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
100 100 100 100 100 100 100 100 100
170 170 192 200 200 200 200 200 200
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
28
100 100 100 100 100 100 100 100 100
P12 End Current - Amps
170 170 192 200 200 200 200 200 200
P13 Corner Current - Amps
30 30 30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
0.4 0.4 0.5 0.5 0.7 0.8 1.0 1.2 1.3
0.0 0.0 0.0 0.0 0.5 0.8 1.0 1.0 1.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
4
(inch)
H1 Ignition Height - mm
5(0.197) 6(0.236) 8(0.315) 8(0.315) 10(0.394) 11(0.433) 13(0.512) 15(0.591) 16(0.630)
H2 Pierce Height - mm(inch)
3(0.115) 3(0.130) 3(0.127) 3(0.125) 4(0.140) 3(0.137) 3(0.135) 5(0.200) 6(0.235)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
M MS 280A GS6 ncode106 pic4
MARKING
Material Carbon Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 280
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
70
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
2.1
2.1
0.0
0.0
2.0
2.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
29
121212730
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
4(0.160)
4(0.160)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
Q MS 280A GS1 ncode106 pic4
QUALIT Y
Material Carbon Steel
Gas Select 1
Cut Gas O2
Start Gas N2
Amperes 280
Shield Gas-1 N2
Shield Gas-2 O2
Code Description
ESAB Welding and Cutting Products
12(0.500) 15(0.600) 16(0.625) 20(0.750) 22(0.875) 25(1.000) 30(1.180) 32(1.250) 35(1.375)
H4 Thickness - mm(inch)
131 137 135 144 146 148 148 148 154
H5 Arc Voltage - Volts
(98) 2240(88) 2110(83) 2010(79) 1780(70) 1520(60) 1270(50) 1140(45) 840(33)
2490
2.7(0.105) 2.8(0.109) 2.8(0.110) 2.9(0.115) 3.0(0.117) 3.4(0.135) 3.2(0.124) 3.0(0.120) 3.6(0.140)
(inch/min)
Speed - mm/min
Kerf - mm(inch)
1 1 1 1 1 1 1 1 1
1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
3.6 3.6 3.6 3.6 3.6 3.6 3.6 3.6 3.6
4.7 4.7 4.7 4.7 4.7 4.7 4.7 4.7 4.7
4.7 4.7 4.7 4.7 4.7 4.7 4.7 4.7 4.7
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
150 150 150 150 150 150 150 150 150
230 266 280 280 280 280 280 280 280
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
30
150 150 150 150 150 150 150 150 150
P12 End Current - Amps
230 266 280 280 280 280 280 280 280
P13 Corner Current - Amps
30 30 30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
0.7 0.7 0.7 0.7 0.7 1.0 1.4 1.5 1.9
0.0 0.0 0.0 0.0 0.0 1.0 1.0 1.0 1.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
6(0.236) 8(0.315) 8(0.315) 10(0.394) 11(0.433) 13(0.512) 15(0.591) 16(0.630) 17(0.669)
3(0.100) 4(0.140) 4(0.140) 7(0.260) 7(0.263) 7(0.265) 7(0.270) 7(0.270) 7(0.270)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
M MS 360A GS6 ncode107 pic31
MARKING
Material Carbon Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 360
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
62
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
2.1
2.1
0.0
0.0
2.0
2.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
31
181818930
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
4(0.160)
4(0.160)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
Q MS 360A GS1 ncode107 pic31
QUALIT Y
Material Carbon Steel
Gas Select 1
Cut Gas O2
Start Gas N2
Amperes 360
Shield Gas-1 N2
Shield Gas-2 O2
Code Description
ESAB Welding and Cutting Products
20(0.750) 22(0.875) 25(1.000) 30(1.180) 32(1.250) 35(1.375) 38(1.500)
H4 Thickness - mm(inch)
133 144 145 148 150 150 150
H5 Arc Voltage - Volts
(100) 2290(90) 2030(80) 1470(58) 1270(50) 990(39) 890(35)
3.8(0.150) 3.9(0.155) 4.1(0.160) 4.4(0.174) 4.6(0.180) 5.0(0.195) 5.5(0.215)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
1 1 1 1 1 1 1
1.2 1.2 1.2 1.2 1.2 1.2 1.2
0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0
3.0 3.0 3.0 3.0 3.0 3.0 3.0
5.7 7.1 7.1 7.1 7.1 7.1 7.1
5.7 7.1 7.1 7.1 7.1 7.1 7.1
0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0
150 150 150 150 150 150 150
360 360 360 360 360 360 360
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
32
150 150 150 150 150 150 150
P12 End Current - Amps
360 360 360 360 360 360 360
P13 Corner Current - Amps
30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.3 1.7 1.7 1.9 2.0 2.0 2.0
0.0 0.0 0.0 0.0 0.0 0.0 1.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
4
(inch)
H1 Ignition Height - mm
10(0.394) 11(0.433) 13(0.512) 15(0.591) 16(0.630) 17(0.669) 19(0.748)
H2 Pierce Height - mm(inch)
4(0.140) 7(0.270) 7(0.280) 8(0.300) 8(0.300) 8(0.300) 8(0.300)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
M MS 400A GS6 ncode108 pic32
MARKING
Material Carbon Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 400
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
52
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
2.1
2.1
0.0
0.0
2.0
2.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
33
181818930
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
4(0.160)
4(0.160)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
Q MS 400A GS1 ncode108 pic32
QUALIT Y
Material Carbon Steel
Gas Select 1
Cut Gas O2
Start Gas N2
Amperes 400
Shield Gas-1 N2
Shield Gas-2 O2
Code Description
ESAB Welding and Cutting Products
32(1.250) 35(1.375) 38(1.500) 40(1.625) 45(1.750) 50(2.000)
H4 Thickness - mm(inch)
150 153 153 160 160 180
H5 Arc Voltage - Volts
(50) 1170(46) 1070(42) 890(35) 970(38) 560(22)
1270
5.2(0.205) 5.2(0.205) 5.7(0.225) 7.0(0.275) 7.0(0.275) 7.6(0.300)
(inch/min)
Speed - mm/min
Kerf - mm(inch)
1 1 1 1 1 1
1.0 1.0 1.0 1.0 1.0 1.0
0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0
2.8 2.8 3.8 3.8 3.8 3.8
4.3 4.3 5.1 5.1 5.1 5.1
4.3 4.3 5.1 5.1 5.1 5.1
3.5 3.5 2.0 2.0 2.0 2.0
3.5 3.5 2.0 2.0 2.0 2.0
200 200 200 200 200 200
400 400 400 400 400 400
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
34
200 200 200 200 200 200
P12 End Current - Amps
400 400 400 400 400 400
P13 Corner Current - Amps
30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6
0.8 0.8 1.0 1.3 1.5 2.0
0.0 0.0 1.0 1.0 1.0 1.0
0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.45 0.45 0.45 0.45 0.45 0.45
4
11(0.430) 12(0.490) 8(0.300) 8(0.315) 8(0.330) 13(0.500)
16(0.630) 17(0.669) 19(0.748) 21(0.827) 22(0.866) 25(0.984)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
Aluminum
Quality
35
36
Q AL 30A GS3 ncode188 pic47
QUALIT Y
Amperes 30
Start Gas N2
Cut Gas N2
Shield Gas-1 N2
Shield Gas-2 CH4
Material Aluminum
Gas Select 3
Code Description
ESAB Welding and Cutting Products
3 3 3
0.0 0.0 0.0
0.0 0.0 0.0
5.2 5.2 5.2
5.2 5.2 5.2
3.0 3.0 1.4
3.0 3.0 1.4
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
37
1.0 1.0 1.0
1.0 1.0 1.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
30 30 30
P10 Start Current - Amps
30 30 30
P11 Cut Current - Amps
15 15 15
P12 End Current - Amps
30 30 30
P13 Corner Current - Amps
30 30 30
P14 Pilot Arc Current - Amps
0.1 0.1 0.1
0.0 0.0 0.0
0.0 0.0 0.0
0.1 0.1 0.1
1.0 1.0 1.0
(0.140) 4(0.140) 4(0.160)
0.10 0.10 0.10
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
4(0.157) 4(0.157) 4(0.157)
3(0.100) 3(0.100) 4(0.160)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
1(0.040) 2(0.080) 3(0.125)
H4 Thickness - mm(inch)
130 145 160
H5 Arc Voltage - Volts
(256) 5080(200) 2790(110)
1.1(0.045) 1.1(0.045) 1.1(0.045)
6500
(inch/min)
Speed - mm/min
Kerf - mm(inch)
Q AL 35A GS3 ncode161 pic18
QUALIT Y
Material Aluminum
Gas Select 3
Cut Gas N2
Start Gas N2
Amperes 35
Shield Gas-1 N2
Shield Gas-2 CH4
Code Description
ESAB Welding and Cutting Products
3 3 3
0.0 0.0 0.0
0.0 0.0 0.0
2.1 2.1 2.1
5.9 5.9 5.9
2.3 2.3 1.1
2.3 2.3 1.1
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
38
0.0 0.0 0.0
1.2 1.2 2.4
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
35 35 35
P10 Start Current - Amps
35 35 35
P11 Cut Current - Amps
35 35 35
P12 End Current - Amps
35 35 35
P13 Corner Current - Amps
30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6
0.1 0.1 0.1
0.0 0.0 0.0
0.6 0.6 0.6
1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
4(0.157) 4(0.157) 4(0.157)
3(0.120) 3(0.120) 3(0.120)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
1(0.040) 2(0.080) 3(0.125)
H4 Thickness - mm(inch)
166 180 182
H5 Arc Voltage - Volts
(240) 4570(180) 3560(140)
1.8(0.071) 1.5(0.060) 1.5(0.060)
6100
(inch/min)
Speed - mm/min
Kerf - mm(inch)
Q AL 50A GS3 ncode162 pic7
QUALIT Y
Amperes 50
Start Gas N2
Cut Gas N2
Shield Gas-1 N2
Shield Gas-2 CH4
Material Aluminum
Gas Select 3
Code Description
ESAB Welding and Cutting Products
3 3 3
0.0 0.0 0.0
0.0 0.0 0.0
1.7 1.7 1.7
5.5 5.5 5.5
2.3 1.7 1.4
2.3 1.7 1.4
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
39
2.0 1.5 1.8
2.0 1.5 1.8
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
50 50 50
P10 Start Current - Amps
50 50 50
P11 Cut Current - Amps
50 50 50
P12 End Current - Amps
50 50 50
P13 Corner Current - Amps
30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6
0.2 0.2 0.2
0.0 0.0 0.0
0.6 0.6 0.6
1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
4(0.157) 5(0.197) 6(0.236)
4(0.160) 5(0.200) 6(0.236)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
4(0.160) 5(0.188) 6(0.250)
H4 Thickness - mm(inch)
176 180 188
H5 Arc Voltage - Volts
(120) 2160(85) 1900(75)
1.7(0.065) 1.7(0.065) 1.7(0.065)
3050
(inch/min)
Speed - mm/min
Kerf - mm(inch)
Q AL 60A GS3 ncode189 pic48
QUALIT Y
Amperes 60
Start Gas N2
Cut Gas N2
Shield Gas-1 N2
Shield Gas-2 CH4
Material Aluminum
Gas Select 3
Code Description
ESAB Welding and Cutting Products
3 3 3 3 3
0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0
5.2 5.2 5.2 5.2 5.2
5.2 5.2 5.2 5.2 5.2
2.0 2.0 2.0 1.5 1.5
2.0 2.0 2.0 1.5 1.5
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
40
1.0 1.5 1.5 1.5 1.5
1.0 1.5 1.5 1.5 1.5
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
45 45 45 45 45
P10 Start Current - Amps
60 60 60 60 60
P11 Cut Current - Amps
13 13 13 12 12
P12 End Current - Amps
60 60 60 60 60
P13 Corner Current - Amps
30 30 30 30 30
P14 Pilot Arc Current - Amps
0.3 0.6 0.6 0.6 0.6
0.0 0.0 0.0 0.5 0.5
0.0 0.0 0.0 0.0 0.0
0.1 0.1 0.1 0.1 0.1
1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.10 0.10 0.10 0.10 0.10
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
4(0.157) 4(0.157) 4(0.157) 4(0.157) 4(0.157)
4(0.160) 3(0.130) 4(0.150) 3(0.135) 4(0.160)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
3(0.125) 4(0.160) 5(0.188) 6(0.250) 8(0.313)
H4 Thickness - mm(inch)
145 155 158 158 165
H5 Arc Voltage - Volts
(210) 3810(150) 3180(125) 1900(75) 1140(45)
1.3(0.050) 1.3(0.050) 1.3(0.050) 1.4(0.055) 1.4(0.055)
5330
(inch/min)
Speed - mm/min
Kerf - mm(inch)
Q AL 100A GS3 ncode163 pic8
QUALIT Y
Material Aluminum
Gas Select 3
Cut Gas N2
Start Gas N2
Amperes 100
Shield Gas-1 N2
Shield Gas-2 CH4
Code Description
ESAB Welding and Cutting Products
3 3 3 3 3
0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0
1.4 1.4 1.4 1.4 1.4
2.8 2.8 2.8 2.8 2.8
3.4 3.4 2.8 2.3 2.3
3.4 3.4 2.8 2.3 2.3
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
41
1.4 1.4 1.1 0.7 0.7
1.4 1.4 1.1 0.7 0.7
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
60 60 60 60 60
P10 Start Current - Amps
100 100 100 100 100
P11 Cut Current - Amps
60 60 60 60 60
P12 End Current - Amps
100 100 100 100 100
P13 Corner Current - Amps
30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6
0.4 0.6 0.6 0.6 0.6
0.0 0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0
(0.157) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
4(0.157) 4(0.157) 4(0.157) 5(0.197) 6(0.236)
4(0.157) 3(0.110) 3(0.118) 3(0.125) 3(0.130)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
5(0.188) 6(0.250) 8(0.313) 10(0.375) 12(0.500)
H4 Thickness - mm(inch)
157 153 154 155 160
H5 Arc Voltage - Volts
(95) 2030(80) 1960(77) 1910(75) 1270(50)
2410
2.7(0.106) 2.0(0.080) 2.0(0.080) 2.0(0.080) 2.0(0.080)
(inch/min)
Speed - mm/min
Kerf - mm(inch)
Q AL 200A GS3 ncode164 pic9
NOTE: Piercing not recommended on thicknesses greater than 38 mm Pierce delay indicated for edge starts greater than 38 mm
QUALIT Y
Material Aluminum
Gas Select 3
Cut Gas N2
Start Gas N2
Amperes 200
Shield Gas-1 N2
Shield Gas-2 CH4
Code Description
ESAB Welding and Cutting Products
10(0.375) 12(0.500) 15(0.600) 16(0.625) 20(0.750) 25(1.000) 30(1.180) 32(1.250) 35(1.375) 38(1.500) 40(1.625) 45(1.750)
H4 Thickness - mm(inch)
155 162 169 172 180 187 180 178 180 185 186 188
H5 Arc Voltage - Volts
(105) 2160(85) 1970(78) 1900(75) 1780(70) 1140(45) 980(39) 910(36) 760(30) 640(25) 600(24) 510(20)
3.0(0.117) 3.0(0.117) 3.0(0.117) 3.0(0.117) 2.8(0.110) 3.6(0.140) 3.9(0.152) 4.0(0.157) 4.6(0.180) 4.6(0.180) 5.0(0.195) 5.8(0.230)
2670
(inch/min)
Speed - mm/min
Kerf - mm(inch)
3 3 3 3 3 3 3 3 3 3 3 3
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.7 0.7 0.7 0.7 0.7 0.7 0.7 0.7 0.7 0.7 0.7 0.7
2.5 3.2 3.2 3.2 3.2 3.2 2.9 2.8 2.8 2.8 2.8 2.8
2.8 2.8 2.8 2.8 2.8 2.8 2.2 2.0 2.0 2.0 2.0 2.0
2.8 2.8 2.8 2.8 2.8 2.8 2.2 2.0 2.0 2.0 2.0 2.0
1.3 1.3 1.3 1.3 1.3 1.7 1.1 0.9 0.9 0.9 0.9 0.9
1.3 1.3 1.3 1.3 1.3 1.7 1.1 0.9 0.9 0.9 0.9 0.9
100 100 100 100 100 100 100 100 100 100 100 100
200 200 200 200 200 200 200 200 200 200 200 200
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
42
100 100 100 100 100 100 100 100 100 100 100 100
P12 End Current - Amps
200 200 200 200 200 200 200 200 200 200 200 200
P13 Corner Current - Amps
30 30 30 30 30 30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
0.5 0.5 0.5 0.5 0.5 0.7 1.0 1.1 1.1 1.1 1.1 1.1
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
5(0.197) 6(0.236) 8(0.315) 8(0.315) 10(0.394) 13(0.512) 15(0.591) 16(0.630) 17(0.669) 19(0.748) 19(0.748) 19(0.748)
4(0.150) 4(0.150) 7(0.274) 8(0.320) 8(0.330) 8(0.330) 8(0.318) 8(0.313) 8(0.300) 8(0.313) 8(0.309) 8(0.300)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
Q AL 260A GS3 ncode165 pic10
QUALIT Y
Material Aluminum
Gas Select 3
Cut Gas N2
Start Gas N2
Amperes 260
Shield Gas-1 N2
Shield Gas-2 CH4
Code Description
ESAB Welding and Cutting Products
12(0.500) 15(0.600) 16(0.625) 20(0.750) 25(1.000) 30(1.180) 32(1.250)
H4 Thickness - mm(inch)
168 172 174 180 188 192 193
H5 Arc Voltage - Volts
(120) 2770(109) 2650(104) 2290(90) 1830(72) 1330(52) 1140(45)
2.8(0.110) 2.9(0.114) 2.9(0.115) 3.0(0.120) 3.7(0.145) 4.0(0.156) 4.1(0.160)
3050
(inch/min)
Speed - mm/min
Kerf - mm(inch)
3 3 3 3 3 3 3
0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.5 0.5 0.5 0.5 0.5 0.5 0.5
3.5 3.5 3.5 3.5 3.5 3.5 3.5
2.8 2.8 2.8 2.8 2.8 2.8 2.8
2.8 2.8 2.8 2.8 2.8 2.8 2.8
1.3 1.3 1.3 1.3 1.3 1.3 1.3
1.3 1.3 1.3 1.3 1.3 1.3 1.3
150 150 150 150 150 150 150
260 260 260 260 260 260 260
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
43
150 150 150 150 150 150 150
P12 End Current - Amps
260 260 260 260 260 260 260
P13 Corner Current - Amps
30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6
0.5 0.5 0.5 0.5 0.5 1.2 1.5
0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
6(0.236) 8(0.315) 8(0.315) 10(0.394) 13(0.512) 15(0.591) 16(0.630)
6(0.230) 6(0.245) 6(0.251) 7(0.270) 10(0.380) 8(0.315) 7(0.290)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
Q AL 360A GS5 ncode166 pic28
NOTE: Piercing not recommended on thicknesses greater than 38 mm Pierce delay indicated for edge starts greater than 38 mm
QUALIT Y
Material Aluminum
Gas Select 5
Cut Gas H35
Start Gas N2
Amperes 360
Shield Gas-1 N2
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
16(0.625) 20(0.750) 25(1.000) 30(1.180) 32(1.250) 35(1.375) 38(1.500) 40(1.625) 45(1.750)
H4 Thickness - mm(inch)
177 180 190 201 205 210 215 216 220
H5 Arc Voltage - Volts
(100) 2290(90) 1520(60) 1250(49) 1140(45) 990(39) 840(33) 780(31) 640(25)
4.8(0.190) 4.4(0.175) 4.8(0.190) 5.2(0.204) 5.3(0.210) 6.1(0.241) 6.9(0.270) 6.9(0.273) 7.1(0.280)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
5 5 5 5 5 5 5 5 5
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
3.8 3.8 3.8 3.8 3.8 3.8 3.8 3.8 3.8
0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
8.5 8.5 8.5 8.5 8.5 8.5 8.5 8.5 8.5
8.5 8.5 8.5 8.5 8.5 8.5 8.5 8.5 8.5
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
150 150 150 150 150 150 150 150 150
360 360 360 360 360 360 360 360 360
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
44
150 150 150 150 150 150 150 150 150
P12 End Current - Amps
360 360 360 360 360 360 360 360 360
P13 Corner Current - Amps
30 30 30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
0.2 0.2 0.5 0.5 0.5 0.5 0.5 0.5 0.5
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.162) 4(0.167)
0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35
4
14(0.551) 10(0.394) 13(0.512) 15(0.591) 16(0.630) 18(0.709) 19(0.748) 19(0.748) 19(0.748)
14(0.540) 10(0.390) 10(0.410) 13(0.519) 14(0.560) 16(0.632) 18(0.700) 18(0.694) 17(0.680)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
Q AL 450A GS5 ncode167 pic45
NOTE: Piercing not recommended on thicknesses greater than 38 mm Pierce delay indicated for edge starts greater than 38 mm
QUALIT Y
Material Aluminum
Gas Select 5
Cut Gas H35
Start Gas N2
Amperes 450
Shield Gas-1 N2
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
20(0.750) 25(1.000) 30(1.180) 32(1.250) 35(1.375) 38(1.500) 40(1.625) 45(1.750) 50(2.000) 55(2.250) 65(2.500) 75(3.000)
H4 Thickness - mm(inch)
155 165 172 175 178 180 182 185 190 196 202 215
H5 Arc Voltage - Volts
(110) 2030(80) 1850(73) 1780(70) 1580(62) 1400(55) 1320(52) 1140(45) 840(33) 760(30) 610(24) 380(15)
5.1(0.200) 5.6(0.220) 5.6(0.220) 5.6(0.220) 5.8(0.230) 6.1(0.240) 6.2(0.246) 6.6(0.260) 7.2(0.285) 7.5(0.296) 7.8(0.307) 10.2(0.400)
2790
(inch/min)
Speed - mm/min
Kerf - mm(inch)
5 5 5 5 5 5 5 5 5 5 5 5
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.8
0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7
5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
200 200 200 200 200 200 200 200 200 200 200 200
450 450 450 450 450 450 450 450 450 450 450 450
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
45
200 200 200 200 200 200 200 200 200 200 200 200
P12 End Current - Amps
450 450 450 450 450 450 450 450 450 450 450 450
P13 Corner Current - Amps
30 30 30 30 30 30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.2 1.2 1.3 1.4 1.5 1.6 2.0 2.0 2.2 2.5 3.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35
4
11(0.433) 14(0.551) 17(0.669) 18(0.709) 18(0.709) 19(0.748) 19(0.748) 19(0.748) 19(0.748) 19(0.748) 20(0.787) 21(0.827)
11(0.450) 14(0.550) 17(0.651) 18(0.690) 18(0.705) 18(0.720) 18(0.726) 19(0.740) 19(0.740) 19(0.760) 20(0.790) 21(0.820)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
46
Stainless Steel
Quality
47
48
M SS 60A GS6 ncode136 pic50
MARKING
Amperes 60
Cut Gas ARG
Start Gas ARG
Shield Gas-1 AIR
Shield Gas-2 NONE
Material Stainless Steel
Gas Select 6
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
75
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
5.2
5.2
0.0
0.0
2.0
2.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
49
121212730
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
3(0.100)
3(0.100)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
Q SS 60A GS18 ncode136 pic50
QUALIT Y
Amperes 60
Start Gas N2
Cut Gas F5
Shield Gas-1 N2
Shield Gas-2 NONE
Material Stainless Steel
Gas Select 5,18
Code Description
ESAB Welding and Cutting Products
18 18 18 18 18
P1 Gas Select
0.0 0.0 0.0 0.0 0.0
P2 PG1 Start - Bar
5.2 5.2 5.2 5.2 5.2
4.8 4.8 4.8 4.8 4.8
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
0.0 0.0 0.0 0.0 0.0
3.0 4.1 3.3 2.6 2.0
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
3.0 4.1 3.3 2.6 2.0
0.0 0.0 0.0 0.0 0.0
P7 SG1 Cut - CMH
P8 SG2 Start - CMH
50
45 45 45 45 45
0.0 0.0 0.0 0.0 0.0
P9 SG2 Cut - CMH
P10 Start Current - Amps
60 60 60 60 60
P11 Cut Current - Amps
13 13 13 13 12
P12 End Current - Amps
60 60 60 60 60
P13 Corner Current - Amps
30 30 30 30 30
P14 Pilot Arc Current - Amps
0.3 0.3 0.3 0.3 0.3
0.5 0.5 0.5 0.5 0.5
0.0 0.0 0.0 0.0 0.0
0.1 0.1 0.1 0.1 0.1
1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.10 0.10 0.10 0.10 0.10
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
4(0.157) 4(0.157) 4(0.157) 4(0.157) 4(0.157)
3(0.135) 3(0.135) 3(0.135) 3(0.135) 4(0.140)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
2(0.080) 3(0.125) 4(0.160) 5(0.188) 6(0.250)
H4 Thickness - mm(inch)
145 145 147 148 150
H5 Arc Voltage - Volts
(210) 3560(140) 2460(97) 1400(55) 1140(45)
1.1(0.045) 1.1(0.045) 1.1(0.045) 1.1(0.045) 1.1(0.045)
5330
(inch/min)
Speed - mm/min
Kerf - mm(inch)
M SS 100A GS6 ncode137 pic8
MARKING
Material Stainless Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 100
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
90
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
3.6
3.6
0.0
0.0
2.0
2.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
51
121212730
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
4(0.160)
4(0.160)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
Q SS 100A GS18 ncode137 pic8
QUALIT Y
Material Stainless Steel
Gas Select 18
Cut Gas F5
Start Gas N2
Amperes 100
Shield Gas-1 N2
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
18 18 18 18
P1 Gas Select
0.0 0.0 0.0 0.0
P2 PG1 Start - Bar
0.0 0.0 3.8 3.1
1.0 1.0 1.0 1.0
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
3.8 3.8 0.0 0.0
5.7 5.7 5.7 5.7
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
5.7 5.7 5.7 5.7
0.0 0.0 0.0 0.0
P7 SG1 Cut - CMH
P8 SG2 Start - CMH
52
60 60 60 60
0.0 0.0 0.0 0.0
P9 SG2 Cut - CMH
P10 Start Current - Amps
100 100 100 100
P11 Cut Current - Amps
60 60 60 60
P12 End Current - Amps
100 100 100 100
P13 Corner Current - Amps
30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6
0.4 0.4 0.4 0.6
0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0
(0.157) 4(0.157) 4(0.157) 4(0.157)
0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
4(0.157) 4(0.157) 4(0.157) 5(0.197)
4(0.142) 4(0.146) 3(0.114) 3(0.130)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
3(0.125) 5(0.188) 6(0.250) 10(0.375)
H4 Thickness - mm(inch)
145 156 155 155
H5 Arc Voltage - Volts
(165) 2160(85) 1650(65) 1140(45)
1.4(0.055) 1.8(0.071) 2.1(0.083) 2.5(0.098)
4190
(inch/min)
Speed - mm/min
Kerf - mm(inch)
M SS 130A GS6 ncode131 pic9
MARKING
Material Stainless Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 130
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
80
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
3.6
3.6
0.0
0.0
4.0
4.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
53
121212730
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
2(0.062)
2(0.062)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
Q SS 130A GS5 ncode131 pic9
QUALIT Y
Material Stainless Steel
Gas Select 5
Cut Gas H35
Start Gas N2
Amperes 130
Shield Gas-1 N2
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
10(0.375) 12(0.500) 15(0.600) 16(0.625) 20(0.750) 25(1.000)
H4 Thickness - mm(inch)
158 163 171 174 183 189
H5 Arc Voltage - Volts
(40) 890(35) 730(29) 680(27) 510(20) 300(12)
1020
3.4(0.135) 3.6(0.140) 3.8(0.148) 3.8(0.151) 4.1(0.160) 4.6(0.180)
(inch/min)
Speed - mm/min
Kerf - mm(inch)
5 5 5 5 5 5
0.0 0.0 0.0 0.0 0.0 0.0
3.1 3.1 3.1 3.1 3.1 3.1
1.0 1.0 1.0 1.0 1.0 1.0
0.0 0.0 0.0 0.0 0.0 0.0
5.7 5.7 5.7 5.7 5.7 5.7
5.7 5.7 5.7 5.7 5.7 5.7
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
54
0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
60 60 60 60 60 60
P10 Start Current - Amps
130 130 130 130 130 130
P11 Cut Current - Amps
60 60 60 60 60 60
P12 End Current - Amps
130 130 130 130 130 130
P13 Corner Current - Amps
30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6
0.6 0.6 0.7 0.7 0.9 1.2
0.0 0.0 0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
8(0.315) 8(0.315) 9(0.354) 10(0.394) 12(0.472) 13(0.512)
8(0.300) 8(0.310) 9(0.372) 10(0.393) 12(0.460) 12(0.470)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
M SS 200A GS6 ncode132 pic10
MARKING
Material Stainless Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 200
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
70
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
2.8
2.8
0.0
0.0
4.0
4.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
55
121616830
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
4(0.160)
4(0.160)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
Q SS 200A GS5 ncode132 pic10
QUALIT Y
Material Stainless Steel
Gas Select 5
Cut Gas H35
Start Gas N2
Amperes 200
Shield Gas-1 N2
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
10(0.375) 12(0.500) 15(0.600) 16(0.625) 20(0.750) 25(1.000) 30(1.180) 32(1.250) 35(1.375) 38(1.500)
H4 Thickness - mm(inch)
169 160 167 170 180 192 198 200 205 210
H5 Arc Voltage - Volts
(50) 1140(45) 1000(39) 940(37) 760(30) 510(20) 400(16) 360(14) 330(13) 300(12)
1270
3.8(0.150) 3.9(0.155) 4.0(0.157) 4.0(0.158) 4.1(0.160) 4.7(0.185) 5.2(0.203) 5.3(0.210) 5.5(0.215) 5.6(0.220)
(inch/min)
Speed - mm/min
Kerf - mm(inch)
5 5 5 5 5 5 5 5 5 5
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
3.8 3.8 3.8 3.8 3.8 3.8 3.8 3.8 3.8 3.8
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
5.7 5.7 5.7 5.7 5.7 5.7 4.6 4.3 4.3 4.3
5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
100 100 100 100 100 100 100 100 100 100
200 200 200 200 200 200 200 200 200 200
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
56
100 100 100 100 100 100 100 100 100 100
P12 End Current - Amps
200 200 200 200 200 200 200 200 200 200
P13 Corner Current - Amps
30 30 30 30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
0.6 0.6 0.7 0.7 1.4 1.6 1.6 1.6 1.7 1.8
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
7(0.276) 6(0.236) 8(0.315) 8(0.315) 10(0.394) 13(0.512) 15(0.591) 16(0.630) 18(0.709) 19(0.748)
7(0.270) 6(0.240) 7(0.276) 7(0.292) 9(0.340) 11(0.430) 12(0.473) 12(0.490) 13(0.521) 14(0.550)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
M SS 260A GS6 ncode133 pic33
MARKING
Material Stainless Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 260
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
65
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
2.1
2.1
0.0
0.0
4.0
4.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
57
1225251230
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
5(0.180)
5(0.180)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
Q SS 260A GS5 ncode133 pic33
QUALIT Y
Material Stainless Steel
Gas Select 5
Cut Gas H35
Start Gas N2
Amperes 260
Shield Gas-1 N2
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
10(0.375) 12(0.500) 15(0.600) 16(0.625) 20(0.750) 25(1.000) 30(1.180) 32(1.250) 35(1.375) 38(1.500)
H4 Thickness - mm(inch)
156 160 170 174 185 190 194 195 198 200
H5 Arc Voltage - Volts
(70) 1400(55) 1210(48) 1140(45) 940(37) 640(25) 540(21) 510(20) 440(17) 380(15)
1780
4.2(0.165) 4.2(0.165) 4.4(0.173) 4.5(0.176) 4.7(0.185) 5.3(0.210) 5.4(0.214) 5.5(0.215) 5.8(0.228) 6.1(0.240)
(inch/min)
Speed - mm/min
Kerf - mm(inch)
5 5 5 5 5 5 5 5 5 5
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
3.8 3.8 3.8 3.8 3.8 3.8 3.8 3.8 3.8 3.8
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1
7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
150 150 150 150 150 150 150 150 150 150
260 260 260 260 260 260 260 260 260 260
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
58
150 150 150 150 150 150 150 150 150 150
P12 End Current - Amps
260 260 260 260 260 260 260 260 260 260
P13 Corner Current - Amps
30 30 30 30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
0.5 0.6 0.7 0.7 1.0 1.2 1.2 1.3 1.6 1.9
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
6(0.236) 6(0.236) 8(0.315) 8(0.315) 10(0.394) 13(0.512) 15(0.591) 16(0.630) 18(0.709) 19(0.748)
6(0.220) 6(0.250) 8(0.310) 8(0.331) 10(0.395) 13(0.530) 14(0.544) 14(0.550) 14(0.545) 14(0.540)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
M SS 360A GS6 ncode134 pic28
MARKING
Material Stainless Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 360
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
62
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
2.1
2.1
0.0
0.0
4.0
4.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
59
181818930
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.161)
0.35
4
4(0.161)
4(0.161)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
Q SS 360A GS5 ncode134 pic28
QUALIT Y
Material Stainless Steel
Gas Select 5
Cut Gas H35
Start Gas N2
Amperes 360
Shield Gas-1 N2
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
20(0.750) 25(1.000) 30(1.180) 32(1.250) 35(1.375) 38(1.500)
H4 Thickness - mm(inch)
180 185 192 195 205 205
H5 Arc Voltage - Volts
(45) 890(35) 800(31) 760(30) 640(25) 510(20)
1140
5.7(0.225) 6.1(0.240) 6.4(0.251) 6.5(0.255) 6.9(0.270) 6.9(0.270)
(inch/min)
Speed - mm/min
Kerf - mm(inch)
5 5 5 5 5 5
0.0 0.0 0.0 0.0 0.0 0.0
3.6 3.6 3.6 3.6 3.6 3.6
0.3 0.3 0.3 0.3 0.3 0.3
0.0 0.0 0.0 0.0 0.0 0.0
8.5 8.5 7.5 7.1 7.1 7.1
8.5 8.5 7.5 7.1 7.1 7.1
0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0
150 150 150 150 150 150
360 360 360 360 360 360
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
60
150 150 150 150 150 150
P12 End Current - Amps
360 360 360 360 360 360
P13 Corner Current - Amps
30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6
0.6 1.0 1.2 1.3 1.6 1.6
0.0 0.0 0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35 0.35
4
13(0.512) 14(0.551) 17(0.669) 18(0.709) 18(0.709) 19(0.748)
13(0.500) 14(0.550) 17(0.651) 18(0.690) 18(0.705) 19(0.730)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
Carbon Steel
Production
61
62
M MS 50A GS6 ncode111 pic1
MARKING
Amperes 50
Cut Gas ARG
Start Gas ARG
Shield Gas-1 AIR
Shield Gas-2 NONE
Material Carbon Steel
Gas Select 6
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
85
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
5.2
5.2
0.0
0.0
2.0
2.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
63
141414730
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
4(0.160)
4(0.160)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
P MS 50A GS1 ncode111 pic1
PRODUCTION
Amperes 50
Start Gas N2
Cut Gas O2
Shield Gas-1 N2
Shield Gas-2 O2
Material Carbon Steel
Gas Select 1
Code Description
ESAB Welding and Cutting Products
1 1 1 1
3.5 3.5 3.5 3.5
0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0
5.9 5.9 5.9 5.9
0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
64
0.8 0.8 0.8 0.8
0.8 0.8 0.8 0.8
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
50 50 50 50
P10 Start Current - Amps
50 50 50 50
P11 Cut Current - Amps
50 50 50 50
P12 End Current - Amps
50 50 50 50
P13 Corner Current - Amps
30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6
0.3 0.3 0.3 0.3
0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
4(0.157) 4(0.157) 4(0.157) 4(0.157)
3(0.120) 3(0.120) 3(0.120) 3(0.120)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
3(0.125) 4(0.160) 5(0.188) 6(0.250)
H4 Thickness - mm(inch)
130 135 137 137
H5 Arc Voltage - Volts
(100) 2290(90) 2160(85) 1780(70)
1.8(0.070) 2.0(0.079) 2.2(0.087) 2.2(0.085)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
M MS 100A GS6 ncode112 pic2
MARKING
Material Carbon Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 100
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
90
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
3.6
3.6
0.0
0.0
2.0
2.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
65
121212730
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
4(0.160)
4(0.160)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
P MS 100A GS9 ncode112 pic2
PRODUCTION
Material Carbon Steel
Gas Select 9
Cut Gas O2
Start Gas N2
Amperes 100
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
9 9 9 9 9 9 9
1.7 1.7 1.7 1.7 1.7 1.7 1.7
0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0
4.1 4.1 4.1 4.1 4.1 4.1 4.1
2.8 2.8 2.8 2.8 2.8 2.8 2.8
2.8 2.8 2.8 2.8 2.8 2.8 2.8
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
66
0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
50 50 50 50 50 50 50
P10 Start Current - Amps
100 100 100 100 100 100 100
P11 Cut Current - Amps
50 50 50 50 50 50 50
P12 End Current - Amps
100 100 100 100 100 100 100
P13 Corner Current - Amps
30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6
0.1 0.1 0.1 0.4 0.4 0.4 0.5
0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
4(0.157) 4(0.157) 4(0.157) 4(0.157) 4(0.157) 5(0.197) 6(0.236)
3(0.125) 3(0.125) 3(0.125) 3(0.125) 3(0.125) 3(0.125) 3(0.125)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
3(0.125) 4(0.160) 5(0.188) 6(0.250) 8(0.313) 10(0.375) 12(0.500)
H4 Thickness - mm(inch)
142 144 146 149 151 153 155
H5 Arc Voltage - Volts
(225) 5160(203) 4470(176) 3560(140) 2700(106) 1900(75) 1520(60)
1.7(0.065) 1.7(0.069) 1.9(0.074) 2.0(0.080) 2.3(0.090) 2.5(0.100) 2.5(0.100)
5720
(inch/min)
Speed - mm/min
Kerf - mm(inch)
M MS 130A GS6 ncode113 pic29
MARKING
Material Carbon Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 130
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
80
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
3.6
3.6
0.0
0.0
2.0
2.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
67
121212730
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
4(0.160)
4(0.160)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
P MS 130A GS2 ncode113 pic29
NOTE: Piercing not recommended on thicknesses greater than 25 mm Pierce delay indicated for edge starts greater than 25 mm
PRODUCTION
Material Carbon Steel
Gas Select 2
Cut Gas O2
Start Gas AIR
Amperes 130
Shield Gas-1 AIR
Shield Gas-2 O2
Code Description
ESAB Welding and Cutting Products
2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5
3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1
3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
68
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
60 60 60 60 60 60 60 60 60 60 60 60 60 60 60
P10 Start Current - Amps
130 130 130 130 130 130 130 130 130 130 130 130 130 130 130
P11 Cut Current - Amps
60 60 60 60 60 60 60 60 60 60 60 60 60 60 60
P12 End Current - Amps
130 130 130 130 130 130 130 130 130 130 130 130 130 130 130
P13 Corner Current - Amps
30 30 30 30 30 30 30 30 30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
0.3 0.3 0.3 0.5 0.5 0.6 0.6 0.6 0.6 1.0 1.5 1.5 1.5 1.5 1.5
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.5 0.5 0.5 0.5 0.5 0.5
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35
4
4(0.157) 4(0.157) 4(0.157) 4(0.157) 4(0.157) 5(0.197) 6(0.236) 8(0.315) 8(0.315) 10(0.394) 13(0.512) 13(0.512) 13(0.512) 13(0.512) 13(0.512)
2(0.080) 2(0.085) 2(0.092) 3(0.100) 3(0.136) 4(0.170) 6(0.240) 6(0.251) 6(0.255) 5(0.214) 10(0.380) 9(0.351) 9(0.340) 10(0.380) 10(0.380)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
3(0.125) 4(0.160) 5(0.188) 6(0.250) 8(0.313) 10(0.375) 12(0.500) 15(0.600) 16(0.625) 20(0.750) 25(1.000) 30(1.180) 32(1.250) 35(1.375) 38(1.500)
H4 Thickness - mm(inch)
127 127 127 127 131 135 145 146 146 144 172 174 175 177 180
H5 Arc Voltage - Volts
(240) 5510(217) 4780(188) 3810(150) 3280(129) 2790(110) 2030(80) 1640(65) 1520(60) 1400(55) 510(20) 420(17) 380(15) 300(12) 250(10)
2.0(0.080) 2.0(0.080) 2.0(0.080) 2.0(0.080) 2.0(0.080) 2.0(0.080) 2.0(0.080) 2.0(0.080) 2.0(0.080) 2.8(0.110) 4.1(0.160) 4.4(0.174) 4.6(0.180) 4.6(0.180) 4.6(0.180)
6100
(inch/min)
Speed - mm/min
Kerf - mm(inch)
M MS 200A GS6 ncode114 pic56
MARKING
Material Carbon Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 200
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
70
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
2.8
2.8
0.0
0.0
2.0
2.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
69
121414730
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
4(0.160)
4(0.160)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
P MS 200A GS2 ncode114 pic56
NOTE: Piercing not recommended on thicknesses greater than 32 mm Pierce delay indicated for edge starts greater than 32 mm
PRODUCTION
Material Carbon Steel
Gas Select 2
Cut Gas O2
Start Gas AIR
Amperes 200
Shield Gas-1 AIR
Shield Gas-2 O2
Code Description
ESAB Welding and Cutting Products
2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1
5.2 5.2 5.2 5.2 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7
5.2 5.2 5.2 5.2 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
70
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
75 75 75 75 75 75 75 75 75 75 75 75 75 75 75
P10 Start Current - Amps
200 200 200 200 200 200 200 200 200 200 200 200 200 200 200
P11 Cut Current - Amps
75 75 75 75 75 75 75 75 75 75 75 75 75 75 75
P12 End Current - Amps
200 200 200 200 200 200 200 200 200 200 200 200 200 200 200
P13 Corner Current - Amps
30 30 30 30 30 30 30 30 30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
0.3 0.3 0.3 0.4 0.4 0.5 0.5 0.7 0.8 1.0 1.2 1.3 1.3 1.3 1.5
0.0 0.0 0.0 0.0 0.0 0.0 0.2 0.5 0.8 1.0 1.0 1.0 1.0 1.0 1.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.236) 6(0.236) 6(0.236) 6(0.236) 6(0.236) 6(0.236) 6(0.236) 6(0.236) 6(0.236) 6(0.236) 6(0.236) 6(0.236) 6(0.236) 6(0.236) 6(0.236)
0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01
6
6(0.236) 6(0.236) 6(0.236) 6(0.236) 6(0.236) 8(0.315) 8(0.315) 10(0.394) 11(0.433) 13(0.512) 15(0.591) 16(0.630) 16(0.630) 16(0.630) 16(0.630)
2(0.063) 2(0.091) 2(0.091) 2(0.091) 3(0.102) 3(0.126) 3(0.134) 4(0.165) 5(0.209) 6(0.252) 7(0.276) 7(0.283) 8(0.319) 7(0.291) 11 (0.449)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
5(0.188) 6(0.250) 8(0.313) 10(0.375) 12(0.500) 15(0.600) 16(0.625) 20(0.750) 22(0.875) 25(1.000) 30(1.180) 32(1.250) 38(1.500) 45(1.750) 50(2.000)
H4 Thickness - mm(inch)
130 140 139 138 143 144 144 145 152 158 159 160 170 173 187
H5 Arc Voltage - Volts
(275) 5330(210) 4420(174) 3560(140) 3050(120) 2670(105) 2533(100) 2030(80) 1650(65) 1270(50) 1040(41) 970(38) 640(25) 430(17) 280(11)
2.1(0.081) 2.3(0.089) 2.5(0.099) 2.8(0.109) 2.8(0.109) 2.9(0.115) 3.0(0.117) 3.2(0.125) 3.2(0.127) 3.3(0.128) 3.6(0.142) 3.7(0.147) 4.6(0.180) 5.3(0.209) 5.7(0.225)
6990
(inch/min)
Speed - mm/min
Kerf - mm(inch)
M MS 260A GS6 ncode127 pic53
MARKING
Material Carbon Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 260
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
70
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
2.1
2.1
0.0
0.0
2.0
2.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
71
121212730
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
4(0.160)
4(0.160)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
P MS 260A GS2 ncode127 pic53
NOTE: Piercing not recommended on thicknesses greater than 38 mm Pierce delay indicated for edge starts greater than 38 mm
PRODUCTION
Material Carbon Steel
Gas Select 2
Cut Gas O2
Start Gas AIR
Amperes 260
Shield Gas-1 AIR
Shield Gas-2 O2
Code Description
ESAB Welding and Cutting Products
10(0.375) 12(0.500) 15(0.600) 16(0.625) 20(0.750) 22(0.875) 25(1.000) 30(1.180) 32(1.250) 35(1.375) 38(1.500) 40(1.625) 45(1.750) 50(2.000) 55(2.250) 65(2.500)
H4 Thickness - mm(inch)
135 137 141 142 145 146 148 152 154 155 158 160 167 175 179 188
H5 Arc Voltage - Volts
(170) 3680(145) 3300(130) 3200(126) 2290(90) 1980(78) 1650(65) 1280(50) 1140(45) 1070(42) 960(38) 890(35) 660(26) 410(16) 360(14) 250(10)
3.2(0.126) 3.8(0.150) 3.8(0.150) 3.8(0.150) 4.1(0.161) 4.4(0.173) 4.4(0.173) 4.4(0.173) 4.4(0.173) 5.1(0.201) 5.1(0.201) 5.1(0.201) 5.1(0.201) 5.1(0.201) 5.5(0.217) 6.4(0.252)
4320
(inch/min)
Speed - mm/min
Kerf - mm(inch)
2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1
7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1
7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1 7.1
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
72
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75
P10 Start Current - Amps
260 260 260 260 260 260 260 260 260 260 260 260 260 260 260 260
P11 Cut Current - Amps
75 75 75 75 75 75 75 75 75 75 75 75 75 75 75 75
P12 End Current - Amps
260 260 260 260 260 260 260 260 260 260 260 260 260 260 260 260
P13 Corner Current - Amps
30 30 30 30 30 30 30 30 30 30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
0.6 0.6 0.6 0.6 0.6 0.6 1.0 1.2 1.5 1.5 1.5 1.5 1.5 1.5 1.5 1.5
0.0 0.0 0.0 0.0 0.0 0.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.197) 6(0.236) 6(0.236) 6(0.236) 6(0.236) 6(0.236) 6(0.236) 5(0.197) 4(0.157) 4(0.157) 4(0.157) 4(0.157) 4(0.157) 4(0.157) 4(0.157) 4(0.157)
0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01
5
5(0.197) 6(0.236) 8(0.315) 8(0.315) 10(0.394) 11(0.433) 13(0.512) 15(0.591) 16(0.630) 17(0.669) 19(0.748) 19(0.748) 19(0.748) 19(0.748) 19(0.748) 19(0.748)
4(0.150) 5(0.201) 5(0.201) 5(0.201) 5(0.201) 5(0.201) 5(0.201) 5(0.201) 5(0.201) 7(0.276) 7(0.276) 7(0.291) 9(0.343) 10(0.402) 11 (0.421) 12(0.461)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
M MS 300A GS6 ncode115 pic5
MARKING
Material Carbon Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 300
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
70
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
2.1
2.1
0.0
0.0
2.0
2.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
73
2020201030
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
4(0.160)
4(0.160)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
P MS 300A GS9 ncode115 pic5
NOTE: Piercing not recommended on thicknesses greater than 45 mm Pierce delay indicated for edge starts greater than 45 mm
PRODUCTION
Material Carbon Steel
Gas Select 9
Cut Gas O2
Start Gas N2
Amperes 300
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
9 9 9 9 9 9 9 9 9 9 9 9 9 9
1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.1 3.2 3.2 3.0 3.2 3.2
5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.1 5.1 5.1
5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.1 5.1 5.1
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
150 150 150 150 150 150 150 150 150 150 150 150 150 150
300 300 300 300 300 300 300 300 300 300 300 300 300 300
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
74
150 150 150 150 150 150 150 150 150 150 150 150 150 150
P12 End Current - Amps
300 300 300 300 300 300 300 300 300 300 300 300 300 300
P13 Corner Current - Amps
30 30 30 30 30 30 30 30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
0.4 0.4 0.5 0.5 0.5 0.5 0.7 0.7 1.1 1.3 1.5 1.7 1.8 2.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 1.0 1.0 1.0 1.0 1.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35
4
6(0.236) 7(0.276) 8(0.315) 9(0.354) 10(0.394) 10(0.394) 11(0.433) 14(0.551) 15(0.591) 16(0.630) 17(0.669) 19(0.748) 21(0.827) 22(0.866)
6(0.250) 7(0.286) 8(0.320) 9(0.345) 10(0.387) 10(0.400) 11(0.418) 14(0.532) 15(0.581) 15(0.600) 16(0.620) 16(0.615) 17(0.670) 18(0.710)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
6(0.250) 8(0.313) 10(0.375) 12(0.500) 15(0.600) 16(0.625) 20(0.750) 25(1.000) 30(1.180) 32(1.250) 35(1.375) 38(1.500) 40(1.625) 45(1.750)
H4 Thickness - mm(inch)
135 140 145 145 150 151 153 160 167 170 173 175 180 182
H5 Arc Voltage - Volts
(190) 4690(185) 4570(180) 3560(140) 3260(128) 3180(125) 2410(95) 1780(70) 1320(52) 1140(45) 1020(40) 890(35) 760(30) 610(24)
3.0(0.120) 3.1(0.123) 3.2(0.126) 3.3(0.130) 3.0(0.119) 2.9(0.115) 3.6(0.140) 4.1(0.160) 4.2(0.167) 4.3(0.170) 4.1(0.160) 4.8(0.190) 4.8(0.190) 4.8(0.190)
4830
(inch/min)
Speed - mm/min
Kerf - mm(inch)
M MS 300A GS6 ncode120 pic5
MARKING
Material Carbon Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 300
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
70
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
2.1
2.1
0.0
0.0
2.0
2.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
75
2020201030
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
4(0.160)
4(0.160)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
S MS 300A GS9 ncode120 pic5
NOTE: Piercing not recommended on thicknesses greater than 45 mm Pierce delay indicated for edge starts greater than 45 mm
SEVER
Material Carbon Steel
Gas Select 9
Cut Gas O2
Start Gas N2
Amperes 300
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
9 9 9 9 9 9 9 9 9 9 9
1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
3.1 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0
5.7 5.7 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5
5.7 5.7 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5 4.5
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
150 150 150 150 150 150 150 150 150 150 150
300 300 300 300 300 300 300 300 300 300 300
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
76
150 150 150 150 150 150 150 150 150 150 150
P12 End Current - Amps
300 300 300 300 300 300 300 300 300 300 300
P13 Corner Current - Amps
30 30 30 30 30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
0.4 0.5 0.5 0.5 0.7 0.7 1.0 1.2 1.3 1.6 1.8
0.0 0.0 0.0 0.0 0.0 0.0 1.0 1.0 1.0 1.0 1.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
5(0.197) 8(0.315) 12(0.472) 11(0.433) 14(0.551) 14(0.551) 15(0.591) 17(0.669) 19(0.748) 20(0.787) 22(0.866)
5(0.200) 8(0.320) 12(0.480) 11(0.430) 14(0.542) 14(0.570) 14(0.551) 16(0.630) 16(0.630) 17(0.669) 17(0.669)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
6(0.250) 10(0.375) 12(0.500) 16(0.625) 20(0.750) 25(1.000) 32(1.250) 35(1.375) 38(1.500) 40(1.625) 45(1.750)
H4 Thickness - mm(inch)
135 145 150 155 160 160 165 170 177 181 185
H5 Arc Voltage - Volts
(240) 5080(200) 4320(170) 3810(150) 3050(120) 3050(120) 1900(75) 1700(67) 1520(60) 1320(52) 1020(40)
2.8(0.110) 3.2(0.126) 2.0(0.080) 3.6(0.140) 3.6(0.140) 3.6(0.140) 5.3(0.209) 6.0(0.236) 7.0(0.276) 7.0(0.276) 7.5(0.295)
6100
(inch/min)
Speed - mm/min
Kerf - mm(inch)
M MS 360A GS6 ncode116 pic55
MARKING
Material Carbon Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 360
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
62
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
2.1
2.1
0.0
0.0
2.0
2.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
77
181818930
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
4(0.160)
4(0.160)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
P MS 360A GS2 ncode116 pic55
NOTE: Piercing not recommended on thicknesses greater than 50 mm Pierce delay indicated for edge starts greater than 50 mm
PRODUCTION
Material Carbon Steel
Gas Select 2
Cut Gas O2
Start Gas AIR
Amperes 360
Shield Gas-1 AIR
Shield Gas-2 O2
Code Description
ESAB Welding and Cutting Products
12(0.500) 15(0.600) 16(0.625) 20(0.750) 22(0.875) 25(1.000) 30(1.180) 32(1.250) 35(1.375) 38(1.500) 40(1.625) 45(1.750) 50(2.000) 55(2.250) 65(2.500)
H4 Thickness - mm(inch)
150 150 150 145 148 150 154 155 158 158 159 160 162 175 180
H5 Arc Voltage - Volts
(170) 3950(156) 3810(150) 2920(115) 2540(100) 2160(85) 1790(70) 1650(65) 1400(55) 1220(48) 1160(46) 970(38) 760(30) 640(25) 460(18)
3.4(0.134) 3.4(0.134) 3.4(0.134) 3.8(0.150) 4.0(0.157) 4.2(0.165) 4.6(0.181) 4.8(0.189) 4.8(0.189) 4.8(0.189) 4.8(0.189) 4.8(0.189) 4.8(0.189) 5.7(0.224) 6.4(0.252)
4320
(inch/min)
Speed - mm/min
Kerf - mm(inch)
2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.0 3.8 3.5 3.5 3.5
5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 7.1 7.3 7.8 8.5 7.1 5.7
5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 7.1 7.1 7.1 7.1 7.1 5.7
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
78
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
75 75 75 75 75 75 75 75 75 75 75 75 75 75 75
P10 Start Current - Amps
360 360 360 360 360 360 360 360 360 360 360 360 360 360 360
P11 Cut Current - Amps
125 125 125 125 125 125 125 125 125 125 125 125 125 125 125
P12 End Current - Amps
360 360 360 360 360 360 360 360 360 360 360 360 360 360 360
P13 Corner Current - Amps
30 30 30 30 30 30 30 30 30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3
0.5 0.5 0.5 1.3 1.5 1.7 1.7 2.0 2.0 2.0 2.0 2.3 3.0 3.0 3.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 1.0 1.0 1.0 1.0 2.0 2.0
0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4 0.4
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.157) 4(0.157) 4(0.157) 4(0.157) 4(0.157) 4(0.157) 4(0.157) 4(0.157) 4(0.157) 4(0.157) 4(0.157) 4(0.157) 4(0.157) 10(0.394) 10(0.394)
0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01 0.01
4
6(0.236) 7(0.276) 8(0.315) 10(0.394) 12(0.472) 13(0.512) 15(0.591) 16(0.630) 17(0.669) 19(0.748) 20(0.787) 22(0.866) 25(0.984) 25(0.984) 25(0.984)
4(0.161) 5(0.205) 6(0.220) 5(0.181) 5(0.181) 5(0.181) 5(0.197) 5(0.201) 5(0.201) 5(0.201) 8(0.311) 8(0.311) 10(0.402) 10(0.402) 10(0.402)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
M MS 400A GS6 ncode117 pic32
MARKING
Material Carbon Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 400
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
52
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
2.1
2.1
0.0
0.0
2.0
2.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
79
181818930
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
4(0.160)
4(0.160)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
P MS 400A GS1 ncode117 pic32
NOTE: Piercing not recommended on thicknesses greater than 50 mm Pierce delay indicated for edge starts greater than 50 mm
PRODUCTION
Material Carbon Steel
Gas Select 1
Cut Gas O2
Start Gas N2
Amperes 400
Shield Gas-1 N2
Shield Gas-2 O2
Code Description
ESAB Welding and Cutting Products
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
2.4 2.4 2.4 2.8 2.5 2.4 2.4 2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.8
4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3
4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3 4.3
3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5
3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5
200 200 200 200 200 200 200 200 200 200 200 200 200 200 200
400 400 400 400 400 400 400 400 400 400 400 400 400 400 400
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
80
200 200 200 200 200 200 200 200 200 200 200 200 200 200 200
P12 End Current - Amps
400 400 400 400 400 400 400 400 400 400 400 400 400 400 400
P13 Corner Current - Amps
30 30 30 30 30 30 30 30 30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
0.4 0.4 0.4 0.4 0.4 0.4 0.5 0.8 1.1 1.1 1.1 1.1 1.3 1.5 2.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 1.0 1.0 1.0 1.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45
4
4(0.157) 5(0.197) 5(0.197) 6(0.236) 8(0.315) 8(0.315) 10(0.394) 13(0.512) 15(0.591) 16(0.630) 18(0.709) 19(0.748) 20(0.787) 22(0.866) 25(0.984)
4(0.165) 5(0.178) 5(0.190) 4(0.150) 5(0.211) 6(0.230) 5(0.185) 6(0.245) 10(0.393) 11(0.450) 11(0.450) 11(0.450) 12(0.480) 13(0.500) 16(0.640)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
6(0.250) 8(0.313) 10(0.375) 12(0.500) 15(0.600) 16(0.625) 20(0.750) 25(1.000) 30(1.180) 32(1.250) 35(1.375) 38(1.500) 40(1.625) 45(1.750) 50(2.000)
H4 Thickness - mm(inch)
130 130 130 132 134 135 136 145 156 160 165 167 168 170 185
H5 Arc Voltage - Volts
(260) 5680(224) 4830(190) 4190(165) 3700(146) 3560(140) 2920(115) 2030(80) 1480(58) 1270(50) 1140(45) 1070(42) 890(35) 760(30) 560(22)
3.3(0.130) 3.6(0.140) 3.8(0.150) 4.1(0.160) 4.3(0.168) 4.3(0.170) 4.3(0.170) 5.5(0.215) 5.6(0.219) 5.6(0.220) 5.6(0.220) 5.8(0.230) 5.8(0.230) 5.8(0.230) 7.1(0.280)
6600
(inch/min)
Speed - mm/min
Kerf - mm(inch)
M MS 450A GS6 ncode129 pic39
MARKING
Material Carbon Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 450
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
65
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
2.1
2.1
0.0
0.0
2.0
2.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
81
1825251230
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
4(0.160)
4(0.160)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
P MS 450A GS9 ncode129 pic39
NOTE: Piercing not recommended on thicknesses greater than 50 mm Pierce delay indicated for edge starts greater than 50 mm
PRODUCTION
Material Carbon Steel
Gas Select 9
Cut Gas O2
Start Gas N2
Amperes 450
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
20(0.750) 22(0.875) 25(1.000) 30(1.180) 32(1.250) 35(1.375) 38(1.500) 40(1.625) 45(1.750) 50(2.000) 55(2.250) 65(2.500) 75(3.000)
H4 Thickness - mm(inch)
137 140 145 149 150 153 155 156 160 165 172 180 185
H5 Arc Voltage - Volts
(118) 2540(100) 2360(93) 1940(76) 1780(70) 1580(62) 1400(55) 1320(52) 1140(45) 840(33) 690(27) 560(22) 250(10)
3.8(0.150) 3.9(0.155) 3.0(0.120) 3.4(0.134) 3.6(0.140) 3.8(0.150) 4.1(0.160) 4.1(0.161) 4.2(0.165) 5.1(0.200) 5.7(0.224) 6.4(0.250) 8.0(0.315)
3000
(inch/min)
Speed - mm/min
Kerf - mm(inch)
9 9 9 9 9 9 9 9 9 9 9 9 9
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
3.3 3.3 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.5 3.5
7.0 7.0 4.3 4.3 4.3 5.7 7.1 7.1 7.1 7.1 7.1 5.7 5.7
7.0 7.0 4.3 4.3 4.3 5.7 7.1 7.1 7.1 7.1 7.1 5.7 5.7
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
200 200 200 200 200 200 200 200 200 200 200 200 200
400 400 450 450 450 450 450 450 450 450 450 450 450
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
82
200 200 200 200 200 200 200 200 200 200 200 200 200
P12 End Current - Amps
400 400 450 450 450 450 450 450 450 450 450 450 450
P13 Corner Current - Amps
30 30 30 30 30 30 30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
0.8 1.5 1.5 1.5 1.5 1.8 2.0 2.2 2.5 3.5 3.5 3.5 3.5
0.0 0.0 0.0 0.0 0.0 0.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.197) 5(0.197) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
5
(inch)
H1 Ignition Height - mm
10(0.394) 11(0.433) 13(0.512) 15(0.591) 16(0.630) 18(0.709) 19(0.748) 20(0.787) 22(0.866) 25(0.984) 25(0.984) 25(0.984) 25(0.984)
H2 Pierce Height - mm(inch)
6(0.236) 6(0.250) 7(0.275) 7(0.271) 7(0.270) 7(0.285) 8(0.300) 8(0.312) 9(0.340) 10(0.400) 11(0.445) 12(0.491) 14(0.540)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
Aluminum
Production
83
84
P AL 35A GS3 ncode171 pic18
PRODUCTION
Material Aluminum
Gas Select 3
Cut Gas N2
Start Gas N2
Amperes 35
Shield Gas-1 N2
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
3 3 3
0.0 0.0 0.0
0.0 0.0 0.0
2.1 2.1 2.1
5.9 5.9 5.9
2.3 2.3 2.0
2.3 2.3 2.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
85
0.0 0.0 0.0
0.0 0.0 0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
35 35 35
P10 Start Current - Amps
35 35 35
P11 Cut Current - Amps
35 35 35
P12 End Current - Amps
35 35 35
P13 Corner Current - Amps
30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6
0.1 0.1 0.1
0.0 0.0 0.0
0.6 0.6 0.6
1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
4(0.157) 4(0.157) 4(0.157)
3(0.120) 3(0.120) 3(0.120)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
1(0.040) 2(0.080) 3(0.125)
H4 Thickness - mm(inch)
160 160 165
H5 Arc Voltage - Volts
(240) 5080(200) 3560(140)
1.8(0.071) 1.5(0.060) 1.5(0.060)
6100
(inch/min)
Speed - mm/min
Kerf - mm(inch)
P AL 50A GS3 ncode172 pic7
PRODUCTION
Amperes 50
Start Gas N2
Cut Gas N2
Shield Gas-1 N2
Shield Gas-2 NONE
Material Aluminum
Gas Select 3
Code Description
ESAB Welding and Cutting Products
3 3 3 3 3
0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0
1.7 1.7 1.7 1.7 1.7
5.5 5.5 5.5 5.5 5.5
4.3 4.3 4.3 4.3 4.3
4.3 4.3 4.3 4.3 4.3
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
86
0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
50 50 50 50 50
P10 Start Current - Amps
50 50 50 50 50
P11 Cut Current - Amps
50 50 50 50 50
P12 End Current - Amps
50 50 50 50 50
P13 Corner Current - Amps
30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6
0.2 0.2 0.2 0.2 0.2
0.0 0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
4(0.157) 4(0.157) 4(0.157) 4(0.157) 6(0.236)
4(0.150) 4(0.156) 4(0.160) 4(0.166) 6(0.250)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
2(0.080) 3(0.125) 4(0.160) 5(0.188) 6(0.250)
H4 Thickness - mm(inch)
168 172 176 180 188
H5 Arc Voltage - Volts
(187) 4060(160) 3050(120) 2160(85) 1900(75)
1.3(0.050) 1.3(0.050) 1.3(0.050) 1.3(0.050) 1.5(0.060)
4750
(inch/min)
Speed - mm/min
Kerf - mm(inch)
P AL 100A GS3 ncode173 pic8
PRODUCTION
Material Aluminum
Gas Select 3
Cut Gas N2
Start Gas N2
Amperes 100
Shield Gas-1 N2
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
3 3 3 3
0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0
1.4 1.4 1.4 1.4
2.8 2.8 2.8 2.8
4.8 3.9 3.0 3.0
4.8 3.9 3.0 3.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
87
0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
60 60 60 60
P10 Start Current - Amps
100 100 100 100
P11 Cut Current - Amps
60 60 60 60
P12 End Current - Amps
100 100 100 100
P13 Corner Current - Amps
30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6
0.6 0.6 0.6 0.6
0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
4(0.157) 4(0.157) 5(0.197) 6(0.236)
4(0.160) 4(0.170) 5(0.180) 5(0.190)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
6(0.250) 8(0.313) 10(0.375) 12(0.500)
H4 Thickness - mm(inch)
153 154 155 160
H5 Arc Voltage - Volts
(80) 1970(78) 1900(75) 1270(50)
2030
1.7(0.065) 1.7(0.065) 1.7(0.065) 1.1(0.045)
(inch/min)
Speed - mm/min
Kerf - mm(inch)
P AL 200A GS3 ncode174 pic9
PRODUCTION
Material Aluminum
Gas Select 3
Cut Gas N2
Start Gas N2
Amperes 200
Shield Gas-1 N2
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
3 3 3 3 3 3 3 3 3 3 3 3
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.7 0.7 0.7 0.7 0.7 0.7 0.7 0.7 0.7 0.7 0.7 0.7
3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 3.2 2.8 2.8
4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.5 4.2 4.1 2.8 2.8
4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.5 4.2 4.1 2.8 2.8
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
100 100 100 100 100 100 100 100 100 100 100 100
200 200 200 200 200 200 200 200 200 200 200 200
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
88
100 100 100 100 100 100 100 100 100 100 100 100
P12 End Current - Amps
200 200 200 200 200 200 200 200 200 200 200 200
P13 Corner Current - Amps
30 30 30 30 30 30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
0.4 0.5 0.5 0.5 0.5 0.5 0.5 0.7 1.0 1.1 1.1 1.1
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
4
(inch)
H1 Ignition Height - mm
4(0.157) 4(0.157) 5(0.197) 6(0.236) 8(0.315) 8(0.315) 10(0.394) 13(0.512) 15(0.591) 16(0.630) 17(0.669) 19(0.748)
H2 Pierce Height - mm(inch)
3(0.115) 3(0.118) 3(0.120) 6(0.218) 7(0.259) 7(0.274) 8(0.330) 7(0.271) 9(0.346) 10(0.375) 10(0.380) 10(0.380)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
6(0.250) 8(0.313) 10(0.375) 12(0.500) 15(0.600) 16(0.625) 20(0.750) 25(1.000) 30(1.180) 32(1.250) 35(1.375) 38(1.500)
H4 Thickness - mm(inch)
140 143 145 162 168 170 180 192 192 192 193 195
H5 Arc Voltage - Volts
(125) 2910(115) 2670(105) 2160(85) 1730(68) 1570(62) 1020(40) 690(27) 560(22) 510(20) 430(17) 380(15)
2.5(0.100) 2.5(0.100) 2.5(0.100) 2.4(0.095) 2.5(0.100) 2.6(0.102) 2.8(0.110) 3.0(0.120) 3.7(0.147) 4.0(0.157) 4.6(0.180) 4.6(0.180)
3180
(inch/min)
Speed - mm/min
Kerf - mm(inch)
P AL 260A GS3 ncode175 pic10
PRODUCTION
Material Aluminum
Gas Select 3
Cut Gas N2
Start Gas N2
Amperes 260
Shield Gas-1 N2
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
3 3 3 3 3 3 3 3 3 3
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5 3.5
4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1
4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1 4.1
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
150 150 150 150 150 150 150 150 150 150
260 260 260 260 260 260 260 260 260 260
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
89
150 150 150 150 150 150 150 150 150 150
P12 End Current - Amps
260 260 260 260 260 260 260 260 260 260
P13 Corner Current - Amps
30 30 30 30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 1.2 1.5
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
6(0.236) 6(0.236) 7(0.276) 8(0.315) 8(0.315) 9(0.354) 10(0.394) 13(0.512) 15(0.591) 16(0.630)
6(0.230) 6(0.251) 7(0.270) 8(0.300) 8(0.329) 9(0.340) 10(0.380) 10(0.380) 9(0.373) 9(0.370)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
6(0.250) 8(0.313) 10(0.375) 12(0.500) 15(0.600) 16(0.625) 20(0.750) 25(1.000) 30(1.180) 32(1.250)
H4 Thickness - mm(inch)
160 163 165 168 172 174 180 192 193 194
H5 Arc Voltage - Volts
(300) 6300(248) 5080(200) 3810(150) 3260(128) 3050(120) 2290(90) 1140(45) 780(31) 640(25)
2.8(0.110) 2.8(0.110) 2.8(0.110) 2.8(0.110) 2.8(0.110) 2.8(0.110) 2.8(0.110) 2.8(0.110) 3.3(0.132) 3.6(0.140)
7620
(inch/min)
Speed - mm/min
Kerf - mm(inch)
P AL 360A GS3 ncode176 pic11
PRODUCTION
Material Aluminum
Gas Select 3
Cut Gas N2
Start Gas N2
Amperes 360
Shield Gas-1 N2
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
3 3 3 3 3 3 3 3 3 3
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.7 0.7 0.7 0.7 0.7 0.7 0.7 0.7 0.7 0.7
2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.8
8.5 8.5 8.5 8.5 8.5 8.5 8.5 5.7 5.7 5.7
8.5 8.5 8.5 8.5 8.5 8.5 8.5 5.7 5.7 5.7
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
150 150 150 150 150 150 150 150 150 150
360 360 360 360 360 360 360 360 360 360
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
90
150 150 150 150 150 150 150 150 150 150
P12 End Current - Amps
360 360 360 360 360 360 360 360 360 360
P13 Corner Current - Amps
30 30 30 30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
0.0 0.1 0.2 0.2 0.2 0.2 0.2 0.5 0.5 0.5
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
4
(inch)
H1 Ignition Height - mm
4(0.157) 4(0.157) 5(0.197) 6(0.236) 8(0.315) 8(0.315) 10(0.394) 13(0.512) 15(0.591) 16(0.630)
H2 Pierce Height - mm(inch)
3(0.110) 4(0.154) 5(0.195) 6(0.250) 7(0.283) 7(0.295) 9(0.340) 11(0.440) 11(0.426) 11 (0.420)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
6(0.250) 8(0.313) 10(0.375) 12(0.500) 15(0.600) 16(0.625) 20(0.750) 25(1.000) 30(1.180) 32(1.250)
H4 Thickness - mm(inch)
147 151 155 160 163 164 168 180 187 190
H5 Arc Voltage - Volts
(230) 5180(204) 4570(180) 4060(160) 3420(135) 3180(125) 2290(90) 1400(55) 1030(41) 890(35)
3.0(0.120) 3.2(0.125) 3.3(0.130) 3.3(0.130) 3.4(0.134) 3.4(0.135) 3.6(0.140) 3.8(0.150) 4.7(0.186) 5.1(0.200)
5840
(inch/min)
Speed - mm/min
Kerf - mm(inch)
P AL 450A GS10 ncode179 pic14
NOTE: Piercing not recommended on thicknesses greater than 38 mm Pierce delay indicated for edge starts greater than 38 mm
PRODUCTION
Material Aluminum
Gas Select 10
Cut Gas N2
Start Gas N2
Amperes 450
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
10 10 10 10 10 10 10 10 10 10 10 10
P1 Gas Select
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
P2 PG1 Start - Bar
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.8 2.8
5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7 5.7
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
P7 SG1 Cut - CMH
P8 SG2 Start - CMH
91
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
200 200 200 200 200 200 200 200 200 200 200 200
P9 SG2 Cut - CMH
P10 Start Current - Amps
450 450 450 450 450 450 450 450 450 450 450 450
P11 Cut Current - Amps
200 200 200 200 200 200 200 200 200 200 200 200
P12 End Current - Amps
450 450 450 450 450 450 450 450 450 450 450 450
P13 Corner Current - Amps
30 30 30 30 30 30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.2 1.2 1.3 1.4 1.5 1.6 2.0 2.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
8(0.315) 8(0.315) 8(0.315) 10(0.394) 13(0.512) 15(0.591) 16(0.630) 18(0.709) 19(0.748) 19(0.748) 19(0.748) 19(0.748)
8(0.310) 8(0.325) 8(0.330) 9(0.350) 9(0.350) 9(0.364) 9(0.370) 10(0.380) 10(0.390) 10(0.390) 10(0.390) 10(0.400)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
12(0.500) 15(0.600) 16(0.625) 20(0.750) 25(1.000) 30(1.180) 32(1.250) 35(1.375) 38(1.500) 40(1.625) 45(1.750) 50(2.000)
H4 Thickness - mm(inch)
160 162 163 170 175 179 180 183 185 186 190 200
H5 Arc Voltage - Volts
(190) 4180(165) 3940(155) 3180(125) 2030(80) 1570(62) 1400(55) 1200(47) 1020(40) 940(37) 760(30) 510(20)
3.7(0.145) 3.8(0.149) 3.8(0.150) 4.3(0.170) 4.4(0.175) 4.6(0.182) 4.7(0.185) 5.2(0.203) 5.6(0.220) 5.8(0.229) 6.4(0.250) 7.2(0.285)
4830
(inch/min)
Speed - mm/min
Kerf - mm(inch)
P AL 600A GS5 ncode177 pic12
NOTE: Piercing not recommended on thicknesses greater than 50 mm Pierce delay indicated for edge starts greater than 50 mm
PRODUCTION
Material Aluminum
Gas Select 5
Cut Gas H35
Start Gas N2
Amperes 600
Shield Gas-1 N2
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000) 30(1.180) 32(1.250) 35(1.375) 38(1.500) 40(1.625) 45(1.750) 50(2.000) 75(3.000)
H4 Thickness - mm(inch)
172 173 173 174 175 178 186 195 215
H5 Arc Voltage - Volts
(90) 2150(85) 2090(82) 2000(79) 1900(75) 1790(70) 1490(59) 1140(45) 640(25)
2290
7.6(0.300) 7.5(0.296) 7.5(0.295) 7.4(0.292) 7.4(0.290) 7.6(0.299) 8.2(0.323) 8.9(0.350) 10.5(0.415)
(inch/min)
Speed - mm/min
Kerf - mm(inch)
5 5 5 5 5 5 5 5 5
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1 3.1
0.7 0.7 0.7 0.7 0.7 0.7 0.7 0.7 0.7
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
9.9 9.9 9.9 9.9 9.9 9.9 9.9 9.9 9.9
9.9 9.9 9.9 9.9 9.9 9.9 9.9 9.9 9.9
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
200 200 200 200 200 200 200 200 200
600 600 600 600 600 600 600 600 600
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
92
200 200 200 200 200 200 200 200 200
P12 End Current - Amps
600 600 600 600 600 600 600 600 600
P13 Corner Current - Amps
30 30 30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
0.5 0.6 0.6 0.7 0.8 0.8 0.9 1.0 1.7
0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45
4
13(0.512) 15(0.591) 16(0.630) 18(0.709) 19(0.748) 20(0.787) 23(0.906) 25(0.984) 25(0.984)
13(0.500) 13(0.529) 14(0.542) 14(0.560) 15(0.580) 15(0.606) 17(0.672) 19(0.750) 24(0.930)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
P AL 600A GS4 ncode178 pic15
Creep speed 1/2 cut speed rst 12 mm
NOTE: Piercing not recommended on thicknesses greater than 76 mm Pierce delay indicated for edge starts greater than 76 mm
PRODUCTION
Material Aluminum
Gas Select 4
Cut Gas H35
Start Gas N2
Amperes 600
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
75(3.000) 100(4.000) 125(5.000) 150(6.000)
H4 Thickness - mm(inch)
170 200 215 230
H5 Arc Voltage - Volts
(25) 380(15) 300(12) 200(8)
640
11.3(0.445) 20.6(0.810) 15.7(0.620) 19.3(0.760)
(inch/min)
Speed - mm/min
Kerf - mm(inch)
4 4 4 4
0.0 0.0 0.0 0.0
1.6 1.6 1.6 1.6
0.4 0.4 0.4 0.4
0.0 0.0 0.0 0.0
7.1 5.1 6.5 6.5
7.1 5.1 6.5 6.5
0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0
200 200 200 200
600 600 600 600
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
93
200 200 200 200
P12 End Current - Amps
600 600 600 600
P13 Corner Current - Amps
30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6
T1 Ramp Up Time - Sec
1.7 3.0 5.0 5.0
T2 Pierce Time - Sec
0.0 0.0 0.0 0.0
T3 Thick Plate Pierce Time - Sec
0.6 0.6 0.6 0.6
T4 Ramp Down Time - Sec
0.45 0.45 0.45 0.45
T5 Gas O Time - Sec
1.0 1.0 1.0 1.0
T6 Raise Lift Time - Sec
(0.500) 13(0.500) 13(0.500) 13(0.500)
13
(inch)
H1 Ignition Height - mm
25(0.984) 29(1.142) 35(1.378) 36(1.417)
H2 Pierce Height - mm(inch)
14(0.540) 29(1.150) 35(1.390) 36(1.400)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
94
Stainless Steel
Production
95
96
M SS 70A GS6 ncode141 pic16
MARKING
Material Stainless Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 70
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
85
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
5.2
5.2
0.0
0.0
4.0
4.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
97
141414730
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.130)
0.35
3
2(0.063)
2(0.063)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
P SS 70A GS3 ncode141 pic16
PRODUCTION
Material Stainless Steel
Gas Select 3
Cut Gas N2
Start Gas N2
Amperes 70
Shield Gas-1 N2
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
3 3 3 3 3
0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0
1.7 1.7 1.7 1.7 1.7
3.5 3.5 3.5 3.5 3.5
9.9 9.9 9.9 9.9 9.9
9.9 9.9 9.9 9.9 9.9
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
98
0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
50 50 50 50 50
P10 Start Current - Amps
70 70 70 70 70
P11 Cut Current - Amps
50 50 50 50 50
P12 End Current - Amps
70 70 70 70 70
P13 Corner Current - Amps
30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6
0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
4(0.157) 4(0.157) 4(0.157) 4(0.157) 4(0.157)
2(0.080) 2(0.080) 3(0.110) 3(0.119) 3(0.120)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
1(0.040) 2(0.080) 3(0.125) 4(0.160) 5(0.188)
H4 Thickness - mm(inch)
140 140 146 148 150
H5 Arc Voltage - Volts
(275) 6100(240) 3300(130) 2540(100) 1780(70)
1.0(0.040) 1.3(0.050) 1.3(0.050) 1.3(0.050) 1.3(0.050)
6980
(inch/min)
Speed - mm/min
Kerf - mm(inch)
M SS 130A GS6 ncode142 pic8
MARKING
Material Stainless Steel
Gas Select 6
Cut Gas ARG
Start Gas ARG
Amperes 130
Shield Gas-1 AIR
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
25(1.000)
H4 Thickness - mm(inch)
80
H5 Arc Voltage - Volts
(100)
0.0(0.000)
2540
(inch/min)
Speed - mm/min
Kerf - mm(inch)
6
3.6
3.6
0.0
0.0
4.0
4.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
99
181818930
0.0
0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
P10 Start Current - Amps
P11 Cut Current - Amps
P12 End Current - Amps
P13 Corner Current - Amps
P14 Pilot Arc Current - Amps
0.1
0.0
0.0
0.1
1.0
(0.160)
0.35
4
4(0.161)
4(0.161)
(inch)
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
P SS 130A GS3 ncode142 pic8
PRODUCTION
Material Stainless Steel
Gas Select 3
Cut Gas N2
Start Gas N2
Amperes 130
Shield Gas-1 N2
Shield Gas-2 NONE
Code Description
ESAB Welding and Cutting Products
3 3 3 3 3 3 3
0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0
1.0 1.0 1.0 1.0 1.0 1.0 1.0
3.8 3.8 3.8 3.8 3.8 3.8 3.8
7.4 6.5 5.7 4.3 4.0 4.0 4.0
7.4 6.5 5.7 4.3 4.0 4.0 4.0
P1 Gas Select
P2 PG1 Start - Bar
P3 PG1 Cut - Bar
P4 PG2 Start - Bar
P5 PG2 Cut - Bar
P6 SG1 Start - CMH
P7 SG1 Cut - CMH
100
0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.0 0.0 0.0 0.0 0.0 0.0 0.0
P8 SG2 Start - CMH
P9 SG2 Cut - CMH
60 60 60 60 60 60 60
P10 Start Current - Amps
130 130 130 130 130 130 130
P11 Cut Current - Amps
60 60 60 60 60 60 60
P12 End Current - Amps
130 130 130 130 130 130 130
P13 Corner Current - Amps
30 30 30 30 30 30 30
P14 Pilot Arc Current - Amps
0.6 0.6 0.6 0.6 0.6 0.6 0.6
0.3 0.4 0.6 0.6 0.7 0.7 0.9
0.0 0.0 0.0 0.0 0.0 0.0 0.0
0.6 0.6 0.6 0.6 0.6 0.6 0.6
1.0 1.0 1.0 1.0 1.0 1.0 1.0
(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160) 4(0.160)
0.35 0.35 0.35 0.35 0.35 0.35 0.35
T1 Ramp Up Time - Sec
T2 Pierce Time - Sec
T3 Thick Plate Pierce Time - Sec
T4 Ramp Down Time - Sec
T5 Gas O Time - Sec
4(0.157) 4(0.157) 5(0.197) 6(0.236) 8(0.315) 8(0.315) 10(0.394)
2(0.090) 3(0.106) 3(0.120) 3(0.125) 5(0.182) 5(0.200) 8(0.300)
4
(inch)
T6 Raise Lift Time - Sec
H1 Ignition Height - mm
H2 Pierce Height - mm(inch)
H3 Cutting Height - mm(inch)
Version 4.7 released on 26Mar15
6(0.250) 8(0.313) 10(0.375) 12(0.500) 15(0.600) 16(0.625) 20(0.750)
H4 Thickness - mm(inch)
150 153 155 160 168 170 180
H5 Arc Voltage - Volts
(85) 1630(64) 1140(45) 760(30) 700(28) 690(27) 640(25)
2160
2.3(0.090) 2.5(0.098) 2.7(0.105) 2.7(0.105) 2.7(0.105) 2.7(0.105) 2.8(0.110)
(inch/min)
Speed - mm/min
Kerf - mm(inch)
Loading...