ESAB M3 Plasma PT-36 G2 Plasma System Cutting Data Instruction manual

Download

PT-36 G2 Plasma System Cutting Data

Cut Data Manual (EN)

0558008435 Version 4.5 released on 13May13

METRIC

BE SURE THIS INFORMATION REACHES THE OPERATOR.

YOU CAN GET EXTRA COPIES THROUGH YOUR SUPPLIER.

CAUTION

These INSTRUCTIONS are for experienced operators. If you are not fully familiar with the principles of operation and safe practices for arc welding and cutting equipment, we urge you to read our booklet, “Precautions and Safe Practices for Arc Welding, Cutting, and Gouging,” Form 52-529. Do NOT permit untrained persons to install, operate, or maintain this equipment. Do NOT attempt to install or operate this equipment until you have read and fully understand these instructions. If you do not fully understand these instructions, contact your supplier for further information. Be sure to read the Safety Precautions before installing or operating this equipment.

USER RESPONSIBILITY

This equipment will perform in conformity with the description thereof contained in this manual and accompanying labels and/or inserts when installed, operated, maintained and repaired in accordance with the instructions provided. This equipment must be checked periodically. Malfunctioning or poorly maintained equipment should not be used. Parts that are broken, missing, worn, distorted or contaminated should be replaced immediately. Should such repair or replacement become necessary, the manufacturer recommends that a telephone or written request for service advice be made to the Authorized Distributor from whom it was purchased.

This equipment or any of its parts should not be altered without the prior written approval of the manufacturer. The user of this equipment shall have the sole responsibility for any malfunction which results from improper use, faulty maintenance, damage, improper repair or alteration by anyone other than the manufacturer or a service facility designated by the manufacturer.

READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.

PROTECT YOURSELF AND OTHERS!

TABLE OF CONTENTS

SUBSECTION TITLE ............................................................................PAGE

Safety Precautions..........................................................................................5

Carbon Steel Quality.......................................................................................13

Aluminum Quality .........................................................................................35

Stainless Steel Quality......................................................................................47

Carbon Steel Production ...................................................................................61

Aluminum Production .................................................................................... 83

Stainless Steel Production................................................................................. 95

Water Injection Aluminum Production.....................................................................117

Water Injection Stainless Steel Production ................................................................ 127

Carbon Steel Air ..........................................................................................141

Aluminum Air ........................................................................................... 155

Stainless Steel Air ........................................................................................ 161

TABLE OF CONTENTS

SECTION 1 SAFETY PRECAUTIONS

1.0 Safety Precautions 1.1 Safety - English

WARNING: These Safety Precautions are for your

protection. They summarize precautionary information from the references listed in Additional Safety Information

section. Before performing any installation or operating procedures, be sure to read and follow the safety precautions listed below as well as all other manuals, material safety data sheets, labels, etc. Failure to observe Safety Precautions can result in injury or death.

PROTECT YOURSELF AND OTHERS -Some welding, cutting, and gouging processes are noisy and require ear protection. The arc, like the sun, e mits

ultraviolet (UV) and other radiation and can injure skin and eyes. Hot metal can cause burns. Training in the proper use of the processes and equipment is essential to prevent accidents. Therefore:

1. Always wear safety glasses with side shields in

any work area, even if welding helmets, face shields, and goggles are also required.

2. Use a face shield tted with the correct lter and

cover plates to protect your eyes, face, neck, and ears from sparks and rays of the arc when operating or observing operations. Warn bystanders not to watch the arc and not to expose themselves to the rays of the electric-arc or hot metal.

3. Wear ameproof gauntlet type gloves, heavy

long-sleeve shirt, cuess trousers, high -topped shoes, and a welding helmet or cap for hair protection, to protect against arc rays and hot sparks or hot metal. A ameproo f apron may also be desirable as protection against radiated heat and sparks.

4. Hot sp arks or metal can lodge in rolled up sleeves,

trouser cus, or pockets. Sleeves and collars should be kept buttoned, and open pockets eliminated from the front of clothing.

5. Protect other personnel from arc rays and hot

sparks with a suitable non-ammable partition or curtains.

6. Use goggles over safety glasses when chipping

slag or grinding. Chipped slag may be hot and can y far. Bystanders should also wear goggles over safety glasses.

1. Remove all combustible materials well away from the work area or cover the materials with a protective non-ammable covering. Combustible materials include wood, cloth, sawdust, liquid and gas fuels, solvents, paints and coatings, paper, etc.

2. Hot sparks or hot metal can fall through cracks or crevices in oors or wall openings and cause a hidden smoldering re or res on the oor below. Make certain that such openings are protected from hot sparks and metal.“

3. Do not weld, cut or perform other hot work until the work piece has been completely cleaned so that there are no substances on the work piece which might produce ammable or toxic vapors. Do not do hot work on closed containers. They may explode.

4. Have re extinguishing equipment handy for instant use, such as a garden hose, water pail, sand bucket, or portable re extinguisher. Be sure you are trained in its use.

5. Do not use equipment beyond its ratings. For example, overloaded welding cable can overheat and create a re hazard.

6. After completing operations, inspect the work area to make certain there are no hot sparks or hot metal which could cause a later re. Use re watchers when necessary.

7. For additional information, refer to NFPA Standard 51B, "Fire Prevention in Use of Cutting and Welding Processes", available from the National Fire Protection Association, Batter y march Park, Quincy, MA 02269.

areas, if movement is conned, or if there is danger of falling.

FIRES AND EXPLOSIONS -- Heat from ames and arcs can start res. Hot slag or sparks can also cause res and explosions. Therefore:

ELECTRICAL SHOCK -- Contact with live electrical parts and ground can cause severe injury or death. DO NOT use AC welding current in damp

SECTION 1 SAFETY PRECAUTIONS

1. Be sure the power source frame (chassis) is connected to the ground system of the input power.

2. Connect the work piece to a good electrical ground.

3. Connect the work cable to the work piece. A poor or missing connection can expose you or others to a fatal shock.

4. Use well-maintained equipment. Replace worn or damaged cables.

5. Keep everything dr y, including clothing, work area, cables, torch/electrode holder, and power source.

6. Make sure that all parts of your body are insulated from work and from ground.

7. Do not stand directly on metal or the earth while working in tight quarters or a damp area; stand on dry boards or an insulating platform and wear rubber-soled shoes.

8. Put on dry, hole-free gloves before turning on the power.

9. Turn o the power before removing your gloves.

3. Welders should use the following procedures to minimize exposure to EMF:

A. Route the electrode and work cables together.

Secure them with tape when possible.

B. Never coil the torch or work cable around your

body.

C. Do not place your body between the torch and

work cables. Route cables on the same side of your body.

D. Connect the work cable to the work piece as close

as possible to the area being welded.

E. Keep welding power source and cables as far

away from your body as possible.

FUMES AND GASES -- Fumes and gases, can cause discomfort or harm, particularly in conned spaces. Do not breathe fumes and gases. Shielding gases can cause asphyxiation.

Therefore:

10. Refer to ANSI/ASC Standard Z49.1 (listed on next page) for specic grounding recommendations. Do not mistake the work lead for a ground cable.

ELECTRIC AND MAGNETIC FIELDS — May be dangerous. Electric current owing through any

conductor causes localized Electric and Magnetic Fields (EMF). Welding

and cutting current creates EMF around welding cables and welding machines. Therefore:

1. Welders having pacemakers should consult their

physician before welding. EMF may interfere with some pacemakers.

2. Exposure to EMF may have other health eects which

are unknown.

1. Always provide adequate ventilation in the work area by natural or mechanical means. Do not weld, cut, or gouge on materials such as galvanized steel, stainless steel, copper, zinc, lead, beryllium, or cadmium unless positive mechanical ventilation is provided. Do not breathe fumes from these materials.

2. Do not operate near degreasing and spraying operations. The heat or arc rays can react with chlorinated hydrocarbon vapors to form phosgene, a highly toxic gas, and other irritant gases.

3. If you develop momentary eye, nose, or throat irritation while operating, this is an indication that ventilation is not adequate. Stop work and take necessary steps to improve ventilation in the work area. Do not continue to operate if physical discomfort persists.

4. Refer to ANSI/ASC Standard Z49.1 (see listing below) for specic ventilation recommendations.

SECTION 1 SAFETY PRECAUTIONS

5. WARNING: This product, when used for welding or cutting, produces fumes or gases which contain chemicals known to the State of California to cause birth defects and, in some cases, cancer. (California Health & Safety Code

§25249.5 et seq.)

CYLINDER HANDLING -- Cylinders, if mishandled, can rupture and violently release gas. Sudden rupture of cylinder, valve, or relief device can injure or kill. Therefore:

1. Use the proper gas for the process and use the

proper pressure reducing regulator designed to operate from the compressed gas cylinder. Do not use adaptors. Maintain hoses and ttings in good condition. Follow manufacturer's operating instructions for mounting regulator to a compressed gas cylinder.

1. Always have qualied personnel perform the installation, troubleshooting, and maintenance work. Do not perform any electrical work unless you are qualied to perform such work.

2. Before performing any maintenance work inside a power source, disconnect the power source from the incoming electrical power.

3. Maintain cables, grounding wire, connections, power cord, and power supply in safe working order. Do not operate any equipment in faulty condition.

4. Do not abuse any equipment or accessories. Keep equipment away from heat sources such as furnaces, wet conditions such as water puddles, oil or grease, corrosive atmospheres and inclement weather.

5. Keep all safety devices and cabinet covers in position and in good repair.

6. Use equipment only for its intended purpose. Do not modify it in any manner.

2. Always secure cylinders in an upright position by chain or strap to suitable hand trucks, undercarriages, benches, walls, post, or racks. Never secure cylinders to work tables or xtures where they may become part of an electrical circuit.

3. When not in use, keep cylinder valves closed. Have valve protection cap in place if regulator is not connected. Secure and move cylinders by using suitable hand trucks. Avoid rough handling of cylinders.

4. Locate cylinders away from heat, sparks, and ames. Never strike an arc on a cylinder.

5. For additional information, refer to CGA Standard P-1, "Precautions for Safe Handling of Compressed G ases in Cylinders", which is available from Compressed Gas Association, 1235 Jeerson Davis Highway, Arlington, VA 22202.

EQUIPMENT MAINTENANCE -- Faulty or improperly maintained equipment can cause injury or death. Therefore:

ADDITIONAL SAFETY INFORMATION -- For more information on safe practices for electric arc welding and cutting equipment, ask your supplier for a copy of "Precautions and Safe Practices for Arc

Welding, Cutting and Gouging", Form 52-529.

The following publications, which are available from the American Welding Society, 550 N.W. LeJuene Road, Miami, FL 33126, are recommended to you:

1. ANSI/ASC Z49.1 - "Safety in Welding and Cutting"

2. AWS C5.1 - "Recommended Practices for Plasma Arc Welding"

3. AWS C5.2 - "Recommended Practices for Plasma Arc Cutting"

4. AWS C5.3 - "Recommended Practices for Air Carbon Arc Gouging and Cutting"

SECTION 1 SAFETY PRECAUTIONS

5. AWS C5.5 - "Recommended Practices for Gas Tungsten Arc Welding“

6. AWS C5.6 - "Recommended Practices for Gas Metal Arc Welding"“

7. AWS SP - "Safe Practices" - Reprint, Welding Handbook.

8. ANSI/AWS F4.1, "Recommended Safe Practices for Welding and Cutting of Containers That Have Held Hazardous Substances."

MEANING OF SYMBOLS - As used throughout this manual: Means Attention! Be Alert! Your safety is involved.

Means immediate hazards which, if not avoided, will result in immediate, serious personal injury or loss of life.

Means potential hazards which could result in personal injury or loss of life.

Means hazards which could result in minor personal injury.

SECTION 1 SAFETY PRECAUTIONS

Hydrogen explosion hazard! Read the following before attempting

DANGER

A hazard exists whenever a water table is used with plasma arc cutting. Severe explosions have resulted from the accumulation of hydrogen beneath the plate being cut. Thousands of dollars in property damage have been caused by these explosions. Personal injury or death could result from such an explosion.

The best available information indicates that three possible sources of hydrogen exists in water tables:

1. Molten Metal Reaction

Most of the hydrogen is liberated by a fast reaction of molten metal from the kerf in the water to form metallic ox-

ides. This reaction explains why reactive metals with greater anity for oxygen, such as aluminum and magnesium, release greater volumes of hydrogen during the cut than does iron or steel. Most of this hydrogen will come to the surface immediately, but some will cling to small metallic particles. These particles will settle to the bottom of the water table and the hydrogen will gradually bubble to the surface.

2. Slow Chemical Reaction

Hydrogen may also result from the slower chemical reactions of cold metal particles with the water, dissimilar metals,

or chemicals in the water. The hydrogen gradually bubbles to the surface.

to cut when using a water table.

3. Plasma & Shield Gas

Hydrogen or other fuel gases, such as Methane (CH4), may come from the plasma or shield gas. H-35 is a commonly

used plasma gas. This gas is 35% hydrogen by volume. When using H-35 at high currents, as much as 125 cfh of hydrogen will be released.

Regardless of the source, the hydrogen gas can collect in pockets formed by the plate being cut and slats on the

table, or pockets from warped plate. There can also be accumulation of hydrogen under the slag tray or even in the air reservoir, if these are part of the table design. The hydrogen, in the presence of oxygen or air, can then be ignited by the plasma arc or a spark from any source.

4. Follow these practices to reduce hydrogen generation and accumulation:

A. Clean the slag (especially ne particles) from the bottom of the table frequently. Rell the table with clean water. B. Do not leave plates on the table overnight or a weekend. C. If a water table has been unused for several hours, vibrate it in some way before the rst plate is laid in position.

This will allow accumulated hydrogen in the refuse to break loose and dissipate before it is conned by a plate on the table. This might be accomplished by laying the rst plate onto the table with a slight jolt, then raising

the plate to permit hydrogen to escape before it is nally set down for cutting. D. If cutting above water, install fans to circulate air between the plate and the water surface. E. If cutting underwater, agitate the water under the plate to prevent accumulation of hydrogen. This can be done

by aerating the water using compressed air. F. If possible, change the level of the water between cuts to dissipate accumulated hydrogen. G. Maintain pH level of the water near 7 (neutral). This reduces the rate of chemical reaction between water and

metals.

SECTION 1 SAFETY PRECAUTIONS

Possible explosion hazard from plasma cutting aluminum-lithium alloys!

Aluminum-Lithium (Al-Li) alloys are used in the aerospace industry because of 10% weight savings over conventional aluminum alloys. It has been reported that molten Al-Li alloys can cause explosions when they come into contact with water. Therefore, plasma cutting of these alloys should not be attempted in the presence of water. These alloys should only be dry cut on a dry table. Alcoa has determined that "dry" cutting on a dry table is safe and gives good cutting results. DO NOT dry cut over water. DO NOT

WARNING

water injection cut.

The following are some of the Al-Li alloys currently available: Alithlite (Alcoa) X8192 (Alcoa) Alithally (Alcoa) Navalite (U. S. Navy) 2090 Alloy (Alcoa) Lockalite (Lockhead) X8090A (Alcoa) Kalite (Kaiser) X8092 (Alcoa) 8091 (Alcan)

For additional details and information on the safe use from the hazards associated with these alloys, contact your aluminum supplier.

Oil And Grease Can Burn Violently!

WARNING

• Never use oil or grease on this torch.

• Handle torch clean hands only on clean surface.

• Use silicone lubricant only where directed.

• Oil and grease are easily ignited and burn violently in the presence

of oxygen under pressure.

Hydrogen explosion hazard.

Do Not Cut Underwater With H-35! Dangerous buildup of hydrogen gas is possible in the water table. Hydrogen gas is extremely explosive. Reduce the water level to 4 inches minimum below the workpiece. Vibrate plate, stir air and water frequently to prevent hydrogen gas buildup.

Spark hazard.

Heat, spatter, and sparks cause re and burns.

• Donotcutnearcombustiblematerial.

• Donotcutcontainersthathaveheldcombustibles.

• Donothaveonyourpersonanycombustibles(e.g.butanelighter).

• Pilotarccancause burns. Keeptorchnozzle awayfrom yourselfand

others when activating plasma process.

• Wearcorrecteyeandbodyprotection.

• Weargauntletgloves,safetyshoesandhat.

• Wearame-retardantclothingthatcoversallexposedareas.

• Wearcuesstrouserstoprevententryofsparksandslag.

Maximum Gas Flow Rates With PT-36 Torch

Gas &

Pressure

Air (85psi / 5.9bar)

Process

Air (85psi / 5.9bar)

Air Curtain

Argon

(125psi / 8.6bar)

CH-4

(75psi / 5.2bar)

H-35 / F5

(75psi / 5.2bar)

Nitrogen

(125psi / 8.6bar)

Oxygen

(125psi / 8.6bar)

Maximum Gas Flow Rates - CFH (CMH)

With PT-36 Torch

EPP-201 EPP-360 EPP-450 EPP-601

269

(7. 6 )

1200

(34)

100

(2.8)

(2.4)

(2.7)

385

(10.9)

(1.9)

269

(7. 6 )

1200

(34)

100

(2.8)

(2.4)

202

(5.7)

496

(14.0)

190

(5.4)

474

(13.4)

1200

(34)

100

(2.8)

(2.4)

202

(5.7)

496

(14.0)

295

(8.4)

474

(13.4)

1200

(34)

100

(2.8)

(2.4)

254

(7. 2)

496

(14.0)

295

(8.4)

Gas Purity

Clean, Dry, Oil Free

Filtered to 25 microns

DIN Quality ISO 8573-1

Oil Quality mg/m3 = 0.1 Class 2

Particle Size 0.1µm Class 1

Temperature +3°C Class 4

99.995%, Filtered to 25 microns

93%, Filtered to 25 microns

99.995%, Filtered to 25 microns

99.99%, Filtered to 25 microns

99.5%, Filtered to 25 microns

Note: No marking with the 600 ampere nozzle.

Carbon Steel

Quality

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Carbon Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 30

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

36 109

PicNo NCode

25 2540 0.0 70 3 3 2.5 0.0 0.0 5.18 5.18 0.00 0.00 2.01 2.01 0.00 0.00

Version 4.5 released on 13May13

ness

First Row Mark Amp: 12

Thick-

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Carbon Steel

Gas Select 1

ESAB Welding and Cutting Products

Amperes 30

Start Gas N2

Cut Gas O2

Shield Gas-1 N2

Shield Gas-2 O2

Thick-

Speed

ness

mm/m

1 3810 1.7 110 3 3 2.0 0.4 0.3 4.82 0.00 0.00 4.48 0.51 0. 51 0.00 0.00

2 1400 1.7 110 3 3 2.0 0.5 0.5 4.82 0.00 0.00 4.48 0.51 0.51 0.00 0.00

Version 4.5 released on 13May13

36 109

PicNo NCode

5 760 1.8 120 4 4 5.1 0.5 0.3 4.82 0.00 0.00 4.48 0.99 0.99 0.00 0.00

4 930 1.7 115 4 4 3.9 0.5 0.3 4.82 0.00 0.00 4.48 0.99 0.99 0.00 0.00

3 1070 1.7 112 4 4 3.0 0.5 0.3 4.82 0.00 0.00 4.48 0.99 0.99 0.00 0.00

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Carbon Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 45

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

25 5080 0.0 85 4 4 4 .1 0.0 0.1 5.18 5.18 0.00 0.00 2.00 2.00 0.00 0.00

25 2540 0.0 85 4 4 4.1 0.0 0.1 5.18 5.18 0.00 0.00 2.00 2.00 0.00 0.00

Version 4.5 released on 13May13

ness

First Row Mark Amp: 14 Second Row Mark Amp: 14

Thick-

17 101

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Carbon Steel

Gas Select 1

ESAB Welding and Cutting Products

Amperes 45

Start Gas N2

Cut Gas O2

Shield Gas-1 N2

Shield Gas-2 O2

Thick-

Speed

ness

mm/m

1 3810 2.3 123 4 4 3.0 0.2 0.1 3.45 0.00 0.00 4.48 0.00 0.00 0.00 0.00

3 1650 2.8 134 4 5 4.6 0.3 0.3 3.45 0.00 0.00 4.00 0.00 0.00 0.00 0.00

2 1980 3.0 131 4 5 3.2 0.3 0.3 3.45 0.00 0.00 4.00 0.00 0.00 0.00 0.00

Version 4.5 released on 13May13

17 101

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Carbon Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 55

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

25 5080 0.0 85 4 4 4 .1 0.0 0.1 5.18 5.18 0.00 0.00 2.00 2.00 0.00 0.00

25 2540 0.0 85 4 4 4.1 0.0 0.1 5.18 5.18 0.00 0.00 2.00 2.00 0.00 0.00

Version 4.5 released on 13May13

ness

First Row Mark Amp: 14 Second Row Mark Amp: 14

Thick-

17 102

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Carbon Steel

Gas Select 1

ESAB Welding and Cutting Products

Amperes 55

Start Gas N2

Cut Gas O2

Shield Gas-1 N2

Shield Gas-2 O2

Thick-

Speed

ness

mm/m

3 3000 2.5 122 4 6 5.1 0.3 0.3 3.45 0.00 0.00 4.00 0.00 0.00 0.00 0.00

4 2160 2.5 127 4 6 6.1 0.3 0.3 3.45 0.00 0.00 4.00 0.00 0.00 0.00 0.00

Version 4.5 released on 13May13

17 102

PicNo NCode

6 1020 3.0 137 4 5 5.1 0.3 0.1 3.45 0.00 0.00 4.13 0.00 0.00 0.00 0.00

5 1400 2.5 132 4 5 5.1 0.3 0 .1 3.45 0.00 0.00 4.13 0.00 0.00 0.00 0.00

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Carbon Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 60

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

37 110

PicNo NCode

25 2540 0.0 75 4 3 2.5 0.0 0.0 5.18 5.18 0.00 0.00 2.01 2.01 0.00 0.00

Version 4.5 released on 13May13

ness

First Row Mark Amp: 12

Thick-

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Carbon Steel

Gas Select 1

ESAB Welding and Cutting Products

Amperes 60

Start Gas N2

Cut Gas O2

Shield Gas-1 N2

Shield Gas-2 O2

Thick-

Speed

ness

mm/m

3 3610 1.5 105 4 3 3.0 0.6 0.3 4.13 0.00 0.00 4.48 0.99 0.99 0.99 0.99

4 3030 1.5 105 4 3 2.9 0.6 0.3 4.13 0.00 0.00 4.48 0.99 0.99 0.99 0.99

5 2290 1. 5 105 4 4 2.8 0.6 0.3 4.13 0.00 0.00 4.48 0.99 0.99 0.99 0.99

6 1900 1.7 108 4 4 3.6 1.0 0.1 4.13 0.00 0.00 4.48 0.99 0.99 0.99 0.99

8 1524 1.7 108 4 4 3.6 1.0 0.1 4.13 0.00 0.00 4.48 0.99 0.99 0.99 0.99

Version 4.5 released on 13May13

37 110

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Carbon Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 100

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

25 7620 0.0 90 4 4 4.1 0.0 0.1 3.59 3.59 0.00 0.00 2.00 2.00 0.00 0.00

25 2540 0.0 90 4 4 4.1 0.0 0.1 3.59 3.59 0.00 0.00 2.00 2.00 0.00 0.00

Version 4.5 released on 13May13

ness

First Row Mark Amp: 12 Second Row Mark Amp: 18

Thick-

2 103

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Carbon Steel

Gas Select 1

ESAB Welding and Cutting Products

Amperes 100

Start Gas N2

Cut Gas O2

Shield Gas-1 N2

Shield Gas-2 O2

Thick-

Speed

ness

mm/m

4 2410 2.0 137 4 6 2.5 0.1 0.2 3.10 0.00 0.00 4.13 2.83 2.83 0.00 0.00

6 2160 2.0 142 4 6 3.2 0.1 0.2 3.10 0.00 0.00 4.13 2.83 2.83 0.00 0.00

5 2310 2.0 138 4 6 2.7 0.1 0.2 3.10 0.00 0.00 4.13 2.83 2.83 0.00 0.00

8 19 05 2.0 137 4 6 3.9 0.2 0.2 3.10 0.00 0.00 4.13 1.42 0.99 1.42 2.26

12 1520 2.3 156 4 6 6.1 0.4 0.2 3.10 0.00 0.00 4.13 2.83 2.83 0.00 0.00

10 177 8 2.0 142 4 6 4.6 0.2 0.2 3.10 0.00 0.00 4.13 2.83 2.83 1.42 1.42

Version 4.5 released on 13May13

2 103

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Carbon Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 130

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

25 7620 0.0 80 4 4 4.1 0.0 0.1 3.59 3.59 0.00 0.00 2.00 2.00 0.00 0.00

25 2540 0.0 80 4 4 4.1 0.0 0.1 3.59 3.59 0.00 0.00 2.00 2.00 0.00 0.00

Version 4.5 released on 13May13

ness

First Row Mark Amp: 12 Second Row Mark Amp: 18

Thick-

29 104

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Carbon Steel

Gas Select 1

ESAB Welding and Cutting Products

Amperes 130

Start Gas N2

Cut Gas O2

Shield Gas-1 N2

Shield Gas-2 O2

Thick-

Speed

ness

mm/m

5 2670 2.4 123 4 6 3.0 0.5 0.2 1.72 0.00 0.00 3.45 3.40 3.40 0.00 0.00

6 2540 2.4 125 4 6 3.3 0.5 0.2 1.72 0.00 0.00 3.45 3.40 3.40 0.00 0.00

8 2342 2.4 129 4 6 2.9 0.5 0.2 1.72 0.00 0.00 3.45 1.70 1.70 1.70 2.26

10 2159 2.4 127 4 6 3.3 0.5 0.2 1.72 0.00 0.00 3.45 1.70 1.70 2.83 2.83

12 1900 2.4 142 4 6 5.1 0.5 0.2 1.72 0.00 0.00 3.45 4.53 4.53 0.00 0.00

15 1490 2.5 149 4 11 6.5 0.5 0.2 1.72 0.00 0.00 3.45 4.53 4.53 0.00 0.00

16 1350 2.5 152 4 13 7. 0 0.5 0.2 1.72 0.00 0.00 3.45 4.53 4.53 0.00 0.00

Version 4.5 released on 13May13

29 104

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Carbon Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 200

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

ness

First Row Mark Amp: 14 Second Row Mark Amp: 23

Thick-

25 7620 0.0 70 4 4 4.1 0.0 0.1 2.76 2.76 0.00 0.00 2.00 2.00 0.00 0.00

25 2540 0.0 70 4 4 4.1 0.0 0.1 2.76 2.76 0.00 0.00 2.00 2.00 0.00 0.00

Version 4.5 released on 13May13

3 105

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Carbon Steel

Gas Select 1

ESAB Welding and Cutting Products

Amperes 200

Start Gas N2

Cut Gas O2

Shield Gas-1 N2

Shield Gas-2 O2

Thick-

Speed

ness

mm/m

10 2340 3.0 125 4 4 1.9 0.4 0.3 1.24 0.00 0.00 3.24 3 .11 3 .11 0.00 0.00

12 2160 3.0 125 4 4 2.0 0.4 0.3 1.24 0.00 0.00 3.24 3.11 3.11 0.00 0.00

15 1970 3.0 133 4 4 3.5 0.4 0.3 1.24 0.00 0.00 3.24 3.11 3.11 0.00 0.00

16 1900 3.0 136 4 4 4.1 0.4 0.3 1.24 0.00 0.00 3.24 3.11 3.11 0.00 0.00

20 1650 3.0 140 4 5 4.6 0.5 0.4 1.24 0.00 0.00 3.24 3 .11 3 .11 0.00 0.00

22 1400 3.0 144 4 9 5.3 0.8 0.4 1. 24 0.00 0.00 3.24 3.11 3.11 0.00 0.00

25 1140 3.0 14 8 4 9 6.1 1.0 0.4 1.24 0.00 0.00 3.24 3 .11 3 .11 0.00 0.00

32 760 3.8 155 4 7 6.6 1.0 0.5 1.24 0.00 0.00 3.24 3 .11 3 .11 0.00 0.00

30 870 3.6 153 4 7 6.5 1.0 0.5 1.24 0.00 0.00 3.24 3 .11 3 .11 0.00 0.00

Version 4.5 released on 13May13

3 105

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Carbon Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 280

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

4 106

PicNo NCode

25 2540 0.0 70 4 4 4.1 0.0 0.1 2.07 2.07 0.00 0.00 2.00 2.00 0.00 0.00

Version 4.5 released on 13May13

ness

First Row Mark Amp: 12

Thick-

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Carbon Steel

Gas Select 1

ESAB Welding and Cutting Products

Amperes 280

Start Gas N2

Cut Gas O2

Shield Gas-1 N2

Shield Gas-2 O2

Thick-

Speed

ness

mm/m

12 2670 2.7 130 4 18 2.5 0.7 0.2 1.72 0.00 0.00 3.58 4.67 4.67 0.00 0.00

15 2390 2.8 137 4 18 4.4 0.7 0.2 1.72 0.00 0.00 3.58 4.67 4.67 0.00 0.00

16 2290 2.8 140 4 18 5.1 0.7 0.2 1.72 0.00 0.00 3.58 4.67 4.67 0.00 0.00

20 2160 2.9 150 4 13 7.9 0.7 0.2 1.72 0.00 0.00 3.58 4.67 4.67 0.00 0.00

22 1850 3.0 155 4 13 9.5 0.7 0.2 1.72 0.00 0.00 3.58 4.67 4.67 0.00 0.00

25 1520 3.4 148 4 18 11.9 1.0 0.2 1.72 0.00 0.00 3.58 4.67 4.67 0.00 0.00

32 1220 3.0 165 4 19 12.7 1.5 0.2 1.72 0.00 0.00 3.58 4.67 4.67 0.00 0.00

30 130 0 3.2 160 4 19 12.5 1.4 0.2 1.72 0.00 0.00 3.58 4.67 4.67 0.00 0.00

35 890 3.6 175 4 22 14. 3 1.9 0.2 1.72 0.00 0.00 3.58 4.67 4.67 0.00 0.00

Version 4.5 released on 13May13

4 106

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Carbon Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 360

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

25 2540 0.0 62 4 4 4.1 0.0 0.1 2.07 2.07 0.00 0.00 2.00 2.00 0.00 0.00

ness

First Row Mark Amp: 18 Second Row Mark Amp: 18

Thick-

25 5080 0.0 62 4 4 4.1 0.0 0.1 2.07 2.07 0.00 0.00 2.00 2.00 0.00 0.00

Version 4.5 released on 13May13

31 107

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Carbon Steel

Gas Select 1

ESAB Welding and Cutting Products

Amperes 360

Start Gas N2

Cut Gas O2

Shield Gas-1 N2

Shield Gas-2 O2

Thick-

Speed

ness

mm/m

20 2540 3.8 143 4 13 6.4 1. 3 0.5 1.24 0.00 0.00 3.03 5.66 5.66 0.00 0.00

32 1270 4.6 157 4 19 10.4 2.0 0.5 1.24 0.00 0.00 3.03 7. 08 7. 0 8 0.00 0.00

35 1070 5.0 158 4 20 10.9 2.0 0.5 1. 24 0.00 0.00 3.03 7. 08 7.0 8 0.00 0.00

30 1480 4.4 15 4 4 19 9.5 1.9 0.5 1. 24 0.00 0.00 3.03 7. 08 7. 0 8 0.00 0.00

25 2030 4.1 145 4 19 7.1 1.7 0.5 1.24 0.00 0.00 3.03 7.0 8 7.0 8 0.00 0.00

22 2290 3.9 144 4 19 6.9 1.7 0.5 1.24 0.00 0.00 3.03 7.0 8 7. 08 0.00 0.00

38 890 5.5 160 4 25 11.7 2.0 0.5 1. 24 0.00 0.00 3.03 7. 08 7. 0 8 0.00 0.00

Version 4.5 released on 13May13

31 107

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Carbon Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 400

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

25 2540 0.0 52 4 4 4 .1 0.0 0 .1 2.07 2.07 0.00 0.00 2.00 2.00 0.00 0.00

ness

First Row Mark Amp: 18 Second Row Mark Amp: 18

Thick-

25 5080 0.0 52 4 4 4.1 0.0 0 .1 2.07 2.07 0.00 0.00 2.00 2.00 0.00 0.00

Version 4.5 released on 13May13

32 108

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Carbon Steel

Gas Select 1

ESAB Welding and Cutting Products

Amperes 400

Start Gas N2

Cut Gas O2

Shield Gas-1 N2

Shield Gas-2 O2

Thick-

Speed

ness

mm/m

32 1270 5.2 150 4 19 10.9 0.8 0.6 1.03 0.00 0.00 2.76 4.25 4.25 3.54 3.54

35 1170 5.2 153 4 19 12 . 4 0.8 0.6 1.03 0.00 0.00 2.76 4.25 4.25 3.54 3.54

38 1070 5.7 153 4 19 7.6 1.0 0.6 1.03 0.00 0.00 3.79 5.09 5.09 1.98 1.98

45 970 7.0 160 4 25 8.4 1.5 0.3 1.03 0.00 0.00 3.79 5.09 5.09 1.98 1.98

40 890 7.0 160 4 25 8.0 1. 3 0.3 1.03 0.00 0.00 3.79 5.09 5.09 1.98 1.98

50 560 7. 6 180 4 25 12 .7 2.0 0.3 1.03 0.00 0.00 3.79 5.09 5.09 1.98 1.98

Version 4.5 released on 13May13

32 108

PicNo NCode

Aluminum

Quality

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Aluminum

Gas Select 3

ESAB Welding and Cutting Products

Amperes 30

Start Gas N2

Cut Gas N2

Shield Gas-1 N2

Shield Gas-2 CH4

Thick-

Speed

ness

mm/m

1 6500 1.1 130 4 3 2.5 0.0 0.1 0.00 0.00 5.17 5.17 3.00 3.00 0.99 0.99

Version 4.5 released on 13May13

47 188

PicNo NCode

3 2790 1.1 160 4 4 4.1 0.0 0.1 0.00 0.00 5.17 5 .17 1.42 1.42 0.99 0.99

2 5080 1.1 145 4 3 2.5 0.0 0.1 0.00 0.00 5.17 5.17 3.00 3.00 0.99 0.99

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Aluminum

Gas Select 3

ESAB Welding and Cutting Products

Amperes 35

Start Gas N2

Cut Gas N2

Shield Gas-1 N2

Shield Gas-2 CH4

Thick-

Speed

ness

mm/m

1 6100 1.8 166 4 3 3.0 0.1 0.4 0.00 0.00 2.07 5.86 2.26 2.26 0.00 1.19

2 4570 1.5 180 4 3 3.0 0.1 0.4 0.00 0.00 2.07 5.86 2.26 2.26 0.00 1.19

3 3560 1. 5 182 4 3 3.0 0.1 0.4 0.00 0.00 2.07 5.86 1.13 1.13 0.00 2.41

Version 4.5 released on 13May13

18 161

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Aluminum

Gas Select 3

ESAB Welding and Cutting Products

Amperes 50

Start Gas N2

Cut Gas N2

Shield Gas-1 N2

Shield Gas-2 CH4

Thick-

Speed

ness

mm/m

4 3050 1.7 176 4 4 4 .1 0.2 0.8 0.00 0.00 1.72 5. 51 2.26 2.26 2.04 2.04

5 2160 1.7 180 4 5 5.1 0.2 0.8 0.00 0.00 1.72 5.51 1.70 1.70 1.50 1.50

6 1900 1.7 188 4 6 6.0 0.2 0.8 0.00 0.00 1.72 5. 51 1.39 1.39 1.75 1.75

7 162

PicNo NCode

Version 4.5 released on 13May13

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Aluminum

Gas Select 3

ESAB Welding and Cutting Products

Amperes 60

Start Gas N2

Cut Gas N2

Shield Gas-1 N2

Shield Gas-2 CH4

Thick-

Speed

ness

mm/m

3 5330 1. 3 145 4 4 4.1 0.0 0.1 0.00 0.00 5.17 5.17 2.01 2.01 0.99 0.99

8 114 0 1.4 165 4 6 4.1 0.5 0.1 0.00 0.00 5.17 5.17 1.50 1.50 1.50 1.50

4 3810 1.3 155 4 3 3.3 0.0 0.1 0.00 0.00 5.17 5.17 2.01 2.01 1.50 1.50

6 1900 1.4 158 4 4 3.4 0.5 0.1 0.00 0.00 5.17 5.17 1.50 1.50 1.50 1.50

5 3180 1.3 158 4 4 3.8 0.0 0.1 0.00 0.00 5.17 5.17 2.01 2.01 1.50 1.50

Version 4.5 released on 13May13

48 189

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Aluminum

Gas Select 3

ESAB Welding and Cutting Products

Amperes 100

Start Gas N2

Cut Gas N2

Shield Gas-1 N2

Shield Gas-2 CH4

Thick-

Speed

ness

mm/m

5 2413 2.7 157 4 4 4.0 0.4 0.5 0.00 0.00 1.38 2.76 3.40 3.40 1.42 1.42

6 2030 2.0 153 4 4 2.8 0.4 0.5 0.00 0.00 1.38 2.76 3.40 3.40 1.42 1.42

8 1970 2.0 15 4 4 4 3.0 0.5 0.7 0.00 0.00 1.38 2.76 2.81 2.81 1.05 1.05

10 1900 2.0 155 4 4 3.2 0.6 0.8 0.00 0.00 1.38 2.76 2.26 2.26 0.71 0.71

12 1270 2.0 160 4 6 3.3 0.6 0.8 0.00 0.00 1.38 2.76 2.26 2.26 0.71 0.71

Version 4.5 released on 13May13

8 163

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Aluminum

Gas Select 3

ESAB Welding and Cutting Products

Amperes 200

Start Gas N2

Cut Gas N2

Shield Gas-1 N2

Shield Gas-2 CH4

Speed

mm/m

ness

NOTE: Piercing not recommended on thicknesses greater than 38 mm Pierce delay indicated for edge starts greater than 38 mm

Thick-

10 2670 3.0 155 4 6 3.8 0.5 0.6 0.00 0.00 0.69 2.48 2.83 2.83 1.27 1.27

12 2160 3.0 162 4 6 3.8 0.5 0.6 0.00 0.00 0.69 3.17 2.83 2.83 1. 27 1. 27

15 1970 3.0 169 4 8 7.0 0.5 0.6 0.00 0.00 0.69 3 .17 2.83 2.83 1.27 1.27

16 1900 3.0 172 4 8 8.1 0.5 0.6 0.00 0.00 0.69 3.17 2.83 2.83 1. 27 1. 27

20 1780 2.8 180 4 8 8.4 0.5 0.6 0.00 0.00 0.69 3.17 2.83 2.83 1.27 1.27

25 1140 3.6 187 4 13 8.4 0.7 0.9 0.00 0.00 0.69 3.17 2.83 2.83 1.70 1.70

32 910 4.0 178 4 13 8.0 0.8 0.6 0.00 0.00 0.69 2.76 1.98 1.98 0.85 0.85

30 980 3.9 180 4 13 8 .1 0.8 0.7 0.00 0.00 0.69 2.87 2.22 2.22 1.08 1.08

35 760 4.6 180 4 8 7.6 0.5 0.6 0.00 0.00 0.69 2.76 1.98 1.98 0.85 0.85

38 640 4.6 185 4 8 8.0 0.5 0.6 0.00 0.00 0.69 2.76 1.98 1.98 0.85 0.85

Version 4.5 released on 13May13

40 600 5.0 186 4 8 7.9 0.5 0.6 0.00 0.00 0.69 2.76 1.98 1.98 0.85 0.85

45 510 5.8 188 4 8 7. 6 0.5 0.6 0.00 0.00 0.69 2.76 1.98 1.98 0.85 0.85

9 164

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Aluminum

Gas Select 3

ESAB Welding and Cutting Products

Amperes 260

Start Gas N2

Cut Gas N2

Shield Gas-1 N2

Shield Gas-2 CH4

Thick-

Speed

ness

mm/m

12 3050 2.8 168 4 6 5.8 0.5 0.6 0.00 0.00 0.48 3.45 2.83 2.83 1.27 1.27

15 2770 2.9 172 4 7 6.2 0.5 0.6 0.00 0.00 0.48 3.45 2.83 2.83 1.27 1.27

16 2650 2.9 174 4 7 6.4 0.5 0.6 0.00 0.00 0.48 3.45 2.83 2.83 1.27 1.27

20 2290 3.0 180 4 8 6.9 0.5 0.6 0.00 0.00 0.48 3.45 2.83 2.83 1.27 1.27

25 1830 3.7 188 4 13 9.7 0.5 0.6 0.00 0.00 0.48 3.45 2.83 2.83 1.27 1.27

32 114 0 4.1 193 4 13 7. 4 0.5 0.6 0.00 0.00 0.48 3.45 2.83 2.83 1.27 1.27

30 1330 4.0 192 4 13 8.0 0.5 0.6 0.00 0.00 0.48 3.45 2.83 2.83 1.27 1.27

Version 4.5 released on 13May13

10 165

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Aluminum

Gas Select 5

ESAB Welding and Cutting Products

Amperes 360

Start Gas N2

Cut Gas H35

Shield Gas-1 N2

Shield Gas-2 NONE

Speed

mm/m

ness

NOTE: Piercing not recommended on thicknesses greater than 38 mm Pierce delay indicated for edge starts greater than 38 mm

Thick-

16 2540 4.8 177 4 18 13.7 0.2 0.2 0.00 3.79 0.34 0.00 8.49 8.49 0.00 0.00

32 114 0 5.3 205 4 25 14.2 0.3 0.2 0.00 3.79 0.34 0.00 8.49 8.49 0.00 0.00

35 990 6.1 210 4 29 16.0 0.4 0.3 0.00 3.79 0.34 0.00 8.49 8.49 0.00 0.00

20 2290 4.4 180 4 18 9.9 0.2 0.2 0.00 3.79 0.34 0.00 8.49 8.49 0.00 0.00

30 12 5 0 5.2 201 4 23 13. 2 0.3 0.2 0.00 3.79 0.34 0.00 8.49 8.49 0.00 0.00

25 1520 4.8 190 4 18 10.4 0.2 0.2 0.00 3.79 0.34 0.00 8.49 8.49 0.00 0.00

38 840 6.9 215 4 32 17. 8 0.4 0.3 0.00 3.79 0.34 0.00 8.49 8.49 0.00 0.00

45 640 7.1 220 4 32 17. 3 0.5 0.2 0.00 3.79 0.34 0.00 8.49 8.49 0.00 0.00

40 780 6.9 216 4 32 17. 6 0.4 0.3 0.00 3.79 0.34 0.00 8.49 8.49 0.00 0.00

Version 4.5 released on 13May13

28 166

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Aluminum

Gas Select 5

ESAB Welding and Cutting Products

Amperes 450

Start Gas N2

Cut Gas H35

Shield Gas-1 N2

Shield Gas-2 NONE

Speed

mm/m

ness

NOTE: Piercing not recommended on thicknesses greater than 38 mm Pierce delay indicated for edge starts greater than 38 mm

Thick-

32 1780 5.6 175 4 18 17. 5 1.2 0.5 0.00 2.76 0.34 0.00 5.66 5.66 0.00 0.00

35 1580 5.8 178 4 18 17.9 1.4 0.5 0.00 2.76 0.34 0.00 5.66 5.66 0.00 0.00

20 2790 5.1 155 4 13 11.4 1.0 0.5 0.00 2.76 0.34 0.00 5.66 5.66 0.00 0.00

30 1850 5.6 172 4 17 16. 5 1.2 0.5 0.00 2.76 0.34 0.00 5.66 5.66 0.00 0.00

25 2030 5.6 165 4 14 14.0 1. 2 0.5 0.00 2.76 0.34 0.00 5.66 5.66 0.00 0.00

38 1400 6.1 180 4 18 18 . 3 1.5 0.5 0.00 2.76 0.34 0.00 5.66 5.66 0.00 0.00

45 114 0 6.6 185 4 19 18. 8 2.0 0.5 0.00 2.76 0.34 0.00 5.66 5.66 0.00 0.00

40 1320 6.2 182 4 18 18.4 1.6 0.5 0.00 2.76 0.34 0.00 5.66 5.66 0.00 0.00

55 760 7.5 19 6 4 19 19. 3 2.2 0.5 0.00 2.76 0.34 0.00 5.66 5.66 0.00 0.00

50 840 7. 2 19 0 4 19 18. 8 2.0 0.5 0.00 2.76 0.34 0.00 5.66 5.66 0.00 0.00

Version 4.5 released on 13May13

75 380 10. 2 215 4 21 20.8 3.0 2.5 0.00 2.76 0.34 0.00 5.66 5.66 0.00 0.00

65 610 7. 8 202 4 20 20.1 2.5 0.5 0.00 2.76 0.34 0.00 5.66 5.66 0.00 0.00

45 167

PicNo NCode

Stainless Steel

Quality

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Stainless Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 60

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

50 136

PicNo NCode

25 2540 0.0 75 4 3 2.5 0.0 0.0 5.18 5.18 0.00 0.00 2.01 2.01 0.00 0.00

Version 4.5 released on 13May13

ness

First Row Mark Amp: 12

Thick-

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Stainless Steel

Gas Select 18

ESAB Welding and Cutting Products

Amperes 60

Start Gas N2

Cut Gas F5

Shield Gas-1 N2

Shield Gas-2 NONE

Thick-

Speed

ness

mm/m

2 5330 1.1 145 4 4 3.4 0.5 0.1 0.00 5.17 4.82 0.00 3.00 3.00 0.00 0.00

3 3560 1.1 145 4 4 3.4 0.5 0.1 0.00 5.17 4.82 0.00 4.05 4.05 0.00 0.00

Version 4.5 released on 13May13

50 136

PicNo NCode

6 114 0 1.1 150 4 4 3.6 0.5 0.1 0.00 5.17 4.82 0.00 2.01 2.01 0.00 0.00

5 1400 1.1 148 4 4 3.4 0.5 0.1 0.00 5.17 4.82 0.00 2.55 2.55 0.00 0.00

4 2460 1.1 147 4 4 3.4 0.5 0.1 0.00 5.17 4.82 0.00 3.29 3.29 0.00 0.00

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Stainless Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 100

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

8 137

PicNo NCode

25 2540 0.0 90 4 4 4.1 0.0 0.1 3.59 3.59 0.00 0.00 2.01 2.01 0.00 0.00

Version 4.5 released on 13May13

ness

First Row Mark Amp: 12

Thick-

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Stainless Steel

Gas Select 18

ESAB Welding and Cutting Products

Amperes 100

Start Gas N2

Cut Gas F5

Shield Gas-1 N2

Shield Gas-2 NONE

Thick-

Speed

ness

mm/m

3 4191 1.4 145 4 10 3.6 0.4 0.4 0.00 0.00 1.03 3.79 5.66 5.66 0.00 0.00

6 1651 2.1 155 4 10 2.9 0.4 0.4 0.00 3.79 1.03 0.00 5.66 5.66 0.00 0.00

5 2159 1.8 156 4 10 3.7 0.4 0.4 0.00 0.00 1.03 3.79 5.66 5.66 0.00 0.00

10 1143 2.5 155 4 10 3.3 0.6 0.4 0.00 3.10 1.03 0.00 5.66 5.66 0.00 0.00

Version 4.5 released on 13May13

8 137

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Stainless Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 130

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

25 2540 0.0 80 4 2 1.6 0.0 0.1 3.59 3.59 0.00 0.00 4.00 4.00 0.00 0.00

ness

First Row Mark Amp: 12 Second Row Mark Amp: 18

Thick-

25 7620 0.0 80 4 2 1.7 0.0 0.1 3.59 3.59 0.00 0.00 4.00 4.00 0.00 0.00

Version 4.5 released on 13May13

9 131

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Stainless Steel

Gas Select 5

ESAB Welding and Cutting Products

Amperes 130

Start Gas N2

Cut Gas H35

Shield Gas-1 N2

Shield Gas-2 NONE

Thick-

Speed

ness

mm/m

10 1020 3.4 158 4 10 7. 6 0.6 0.4 0.00 3.10 1.03 0.00 5.66 5.66 0.00 0.00

12 890 3.6 163 4 10 7. 9 0.6 0.4 0.00 3.10 1.03 0.00 5.66 5.66 0.00 0.00

15 730 3.8 171 4 11 9.4 0.7 0.4 0.00 3.10 1.03 0.00 5.66 5.66 0.00 0.00

16 680 3.8 174 4 12 10.0 0.7 0.4 0.00 3.10 1.03 0.00 5.66 5.66 0.00 0.00

20 510 4.1 183 4 13 11. 7 0.8 0.4 0.00 3.10 1.03 0.00 5.66 5.66 0.00 0.00

25 300 4.6 189 4 15 11. 9 1.2 0.4 0.00 3.10 1.03 0.00 5.66 5.66 0.00 0.00

Version 4.5 released on 13May13

9 131

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Stainless Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 200

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

25 7620 0.0 70 4 4 4.1 0.0 0.1 2.76 2.76 0.00 0.00 4.00 4.00 0.00 0.00

25 2540 0.0 70 4 4 4.1 0.0 0.1 2.76 2.76 0.00 0.00 4.00 4.00 0.00 0.00

Version 4.5 released on 13May13

ness

First Row Mark Amp: 14 Second Row Mark Amp: 23

Thick-

10 132

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Stainless Steel

Gas Select 5

ESAB Welding and Cutting Products

Amperes 200

Start Gas N2

Cut Gas H35

Shield Gas-1 N2

Shield Gas-2 NONE

Thick-

Speed

ness

mm/m

10 1270 3.8 169 4 9 6.9 0.6 0.7 0.00 3.79 1.03 0.00 5.66 5.66 0.00 0.00

12 114 0 3.9 160 4 9 6.1 0.6 0.7 0.00 3.79 1.03 0.00 5.66 5.66 0.00 0.00

15 1000 4.0 167 4 9 7. 0 0.6 0.7 0.00 3.79 1.03 0.00 5.66 5.66 0.00 0.00

16 940 4.0 170 4 10 7.4 0.6 0.7 0.00 3.79 1.03 0.00 5.66 5.66 0.00 0.00

20 760 4.1 180 4 10 8.6 0.6 0.7 0.00 3.79 1.03 0.00 5.66 5.66 0.00 0.00

25 510 4.7 192 4 13 10.9 1.0 0.7 0.00 3.79 1.03 0.00 5.66 5.66 0.00 0.00

32 360 5.3 200 4 18 12.4 1. 5 0.5 0.00 3.79 1.03 0.00 4.25 5.66 0.00 0.00

35 330 5.5 205 4 18 13.2 1.7 0.5 0.00 3.79 1.03 0.00 4.25 5.66 0.00 0.00

30 400 5.2 198 4 16 12.0 1.4 0.6 0.00 3.79 1.03 0.00 4.64 5.66 0.00 0.00

38 300 5.6 210 4 19 14.0 1.8 0.5 0.00 3.79 1.03 0.00 4.25 5.66 0.00 0.00

Version 4.5 released on 13May13

10 132

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Stainless Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 260

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

25 5080 0.0 65 4 5 4.6 0.0 0.1 2.07 2.07 0.00 0.00 4.00 4.00 0.00 0.00

25 2540 0.0 65 4 5 4.6 0.0 0 .1 2.07 2.07 0.00 0.00 4.00 4.00 0.00 0.00

Version 4.5 released on 13May13

ness

First Row Mark Amp: 25 Second Row Mark Amp: 25

Thick-

33 133

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Stainless Steel

Gas Select 5

ESAB Welding and Cutting Products

Amperes 260

Start Gas N2

Cut Gas H35

Shield Gas-1 N2

Shield Gas-2 NONE

Thick-

Speed

ness

mm/m

10 178 0 4.2 156 4 10 5.6 0.3 0.2 0.00 3.79 1.03 0.00 7. 08 7. 0 8 0.00 0.00

12 140 0 4.2 160 4 10 6.4 0.3 0.2 0.00 3.79 1.03 0.00 7. 08 7. 0 8 0.00 0.00

15 1210 4.4 170 4 12 7.9 0.4 0.2 0.00 3.79 1.03 0.00 7. 08 7. 0 8 0.00 0.00

16 114 0 4.5 174 4 13 8.4 0.4 0.2 0.00 3.79 1.03 0.00 7.0 8 7.0 8 0.00 0.00

20 940 4.7 185 4 15 10.0 0.6 0.2 0.00 3.79 1.03 0.00 7.0 8 7.0 8 0.00 0.00

25 640 5.3 190 4 19 13.5 1.0 0.2 0.00 3.79 1.03 0.00 7. 0 8 7. 0 8 0.00 0.00

32 510 5.5 195 4 19 14.0 1.3 0.2 0.00 3.79 1.03 0.00 7. 0 8 7. 0 8 0.00 0.00

30 540 5.4 194 4 19 13.8 1.2 0.2 0.00 3.79 1.03 0.00 7. 0 8 7. 0 8 0.00 0.00

35 440 5.8 19 8 4 19 13.8 1.6 0.2 0.00 3.79 1.03 0.00 7.0 8 7.0 8 0.00 0.00

38 380 6.1 200 4 19 13 .7 1.9 0.2 0.00 3.79 1.03 0.00 7. 0 8 7. 0 8 0.00 0.00

Version 4.5 released on 13May13

33 133

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Stainless Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 360

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

25 5080 0.0 62 4 4 4.1 0.0 0.1 2.10 2.10 0.00 0.00 4.00 4.00 0.00 0.00

25 2540 0.0 62 4 4 4.1 0.0 0.1 2.10 2.10 0.00 0.00 4.00 4.00 0.00 0.00

Version 4.5 released on 13May13

ness

First Row Mark Amp: 18 Second Row Mark Amp: 45

Thick-

28 134

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

QUALITY

Material Stainless Steel

Gas Select 5

ESAB Welding and Cutting Products

Amperes 360

Start Gas N2

Cut Gas H35

Shield Gas-1 N2

Shield Gas-2 NONE

Thick-

Speed

ness

mm/m

20 114 0 5.7 180 4 18 12.7 0.6 0.5 0.00 3.58 0.34 0.00 8.49 8.49 0.00 0.00

32 760 6.5 195 4 25 17. 5 1.3 0.5 0.00 3.58 0.34 0.00 7. 08 7. 0 8 0.00 0.00

35 640 6.9 205 4 25 17.9 1.6 0.5 0.00 3.58 0.34 0.00 7. 08 7. 08 0.00 0.00

30 800 6.4 192 4 25 16.5 1.2 0.5 0.00 3.58 0.34 0.00 7. 47 7. 47 0.00 0.00

25 890 6.1 185 4 25 14.0 1.0 0.5 0.00 3.58 0.34 0.00 8.49 8.49 0.00 0.00

38 510 6.9 205 4 25 18.5 1.6 0.5 0.00 3.58 0.34 0.00 7. 08 7.0 8 0.00 0.00

Version 4.5 released on 13May13

28 134

PicNo NCode

Carbon Steel

Production

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Carbon Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 50

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

25 10160 0.0 85 4 4 4.1 0.0 0.1 5.18 5.18 0.00 0.00 2.00 2.00 0.00 0.00

25 2540 0.0 85 4 4 4.1 0.0 0.1 5.18 5.18 0.00 0.00 2.00 2.00 0.00 0.00

Version 4.5 released on 13May13

First Row Mark Amp: 14 Second Row Mark Amp: 14

ness

Thick-

1 111

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

PRODUCTION

Speed

mm/m

Material Carbon Steel

Gas Select 1

Amperes 50

Start Gas N2

Cut Gas O2

Shield Gas-1 N2

Shield Gas-2 O2

ness

Thick-

3 2540 1.8 130 4 4 3.0 0.3 0.1 3.45 0.00 0.00 5.86 0.00 0.00 0.79 0.79

6 178 0 2.2 137 4 4 3.0 0.3 0.1 3.45 0.00 0.00 5.86 0.00 0.00 0.79 0.79

5 2160 2.2 137 4 4 3.0 0.3 0.1 3.45 0.00 0.00 5.86 0.00 0.00 0.79 0.79

4 2290 2.0 135 4 4 3.0 0.3 0.1 3.45 0.00 0.00 5.86 0.00 0.00 0.79 0.79

1 111

PicNo NCode

ESAB Welding and Cutting Products

Version 4.5 released on 13May13

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Carbon Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 100

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

25 7620 0.0 90 4 4 4.1 0.0 0.1 3.59 3.59 0.00 0.00 2.00 2.00 0.00 0.00

25 2540 0.0 90 4 4 4.1 0.0 0.1 3.59 3.59 0.00 0.00 2.00 2.00 0.00 0.00

Version 4.5 released on 13May13

First Row Mark Amp: 12 Second Row Mark Amp: 18

ness

Thick-

2 112

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

PRODUCTION

Speed

mm/m

Material Carbon Steel

Gas Select 9

Amperes 100

Start Gas N2

Cut Gas O2

Shield Gas-1 AIR

Shield Gas-2 NONE

ness

Thick-

3 5720 1.7 142 4 6 3.2 0.1 0.1 3.10 0.00 0.00 4.13 2.83 2.83 0.00 0.00

4 5160 1.7 14 4 4 6 3.2 0.1 0.1 3.10 0.00 0.00 4.13 2.83 2.83 0.00 0.00

5 4470 1.9 146 4 6 3.2 0.1 0.1 3.10 0.00 0.00 4.13 2.83 2.83 0.00 0.00

6 3560 2.0 149 4 6 3.2 0.1 0.1 3.10 0.00 0.00 4.13 2.83 2.83 0.00 0.00

8 2700 2.3 151 4 6 3.2 0.2 0.1 3.10 0.00 0.00 4 .13 2.83 2.83 0.00 0.00

12 1520 2.5 155 4 6 3.2 0.4 0.1 3.10 0.00 0.00 4.13 2.83 2.83 0.00 0.00

10 1900 2.5 153 4 6 3.2 0.2 0.1 3.10 0.00 0.00 4.13 2.83 2.83 0.00 0.00

2 112

PicNo NCode

ESAB Welding and Cutting Products

Version 4.5 released on 13May13

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Carbon Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 130

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

25 7620 0.0 80 4 4 4.1 0.0 0.1 3.59 3.59 0.00 0.00 2.00 2.00 0.00 0.00

25 2540 0.0 80 4 4 4.1 0.0 0.1 3.59 3.59 0.00 0.00 2.00 2.00 0.00 0.00

Version 4.5 released on 13May13

First Row Mark Amp: 12 Second Row Mark Amp: 18

ness

Thick-

29 113

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

PRODUCTION

Speed

mm/m

Material Carbon Steel

Gas Select 2

Amperes 130

Cut Gas O2

Start Gas AIR

Shield Gas-1 AIR

Shield Gas-2 O2

ness

NOTE: Piercing not recommended on thicknesses greater than 25 mm Pierce delay indicated for edge starts greater than 25 mm

Thick-

3 6100 2.0 127 4 3 2.0 0.3 0.2 1.72 0.00 0.00 3.45 3.11 3 .11 0.00 0.00

5 4780 2.0 127 4 3 2.3 0.3 0.2 1.72 0.00 0.00 3.45 3.11 3.11 0.00 0.00

6 3810 2.0 127 4 3 2.5 0.3 0.2 1.72 0.00 0.00 3.45 3 .11 3 .11 0.00 0.00

4 5510 2.0 127 4 3 2.2 0.3 0.2 1.72 0.00 0.00 3.45 3 .11 3 .11 0.00 0.00

8 3280 2.0 131 4 4 3.5 0.5 0.2 1.72 0.00 0.00 3.45 3 .11 3 .11 0.00 0.00

12 2030 2.0 145 4 7 6 .1 0.6 0.2 1.72 0.00 0.00 3.45 3 .11 3 .11 0.00 0.00

15 16 40 2.0 146 4 7 6.4 0.6 0.2 1.72 0.00 0.00 3.45 3 .11 3 .11 0.00 0.00

10 2790 2.0 135 4 4 4.3 0.6 0.2 1.72 0.00 0.00 3.45 3.11 3.11 0.00 0.00

16 1520 2.0 146 4 7 6.5 0.6 0.2 1.72 0.00 0.00 3.45 3 .11 3 .11 0.00 0.00

20 1400 2.8 14 4 4 7 5.4 1.0 0.2 1.72 0.00 0.00 3.45 3 .11 3 .11 0.00 0.00

25 510 4.1 172 4 10 9.7 1.5 1.0 1.72 0.00 0.00 3.45 3 .11 3 .11 0.00 0.00

32 380 4.6 175 4 10 8.6 1.5 1.0 1.72 0.00 0.00 3.45 3 .11 3 .11 0.00 0.00

35 300 4.6 177 4 10 9.7 1.5 1.0 1.72 0.00 0.00 3.45 3 .11 3 .11 0.00 0.00

30 420 4.4 174 4 10 8.9 1.5 1.0 1.72 0.00 0.00 3.45 3 .11 3 .11 0.00 0.00

38 250 4.6 180 4 10 9.7 1.5 1.0 1.72 0.00 0.00 3.45 3.11 3.11 0.00 0.00

29 113

PicNo NCode

ESAB Welding and Cutting Products

Version 4.5 released on 13May13

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Carbon Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 200

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

25 7620 0.0 70 4 4 4.1 0.0 0.1 2.76 2.76 0.00 0.00 2.00 2.00 0.00 0.00

25 2540 0.0 70 4 4 4.1 0.0 0.1 2.76 2.76 0.00 0.00 2.00 2.00 0.00 0.00

Version 4.5 released on 13May13

First Row Mark Amp: 14 Second Row Mark Amp: 23

ness

Thick-

56 114

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

PRODUCTION

Speed

mm/m

Material Carbon Steel

Gas Select 2

Amperes 200

Cut Gas O2

Start Gas AIR

Shield Gas-1 AIR

Shield Gas-2 O2

ness

NOTE: Piercing not recommended on thicknesses greater than 32 mm Pierce delay indicated for edge starts greater than 32 mm

Thick-

5 6990 2.1 130 6 13 1.6 0.3 0.5 1.72 0.00 0.00 4 .13 5.24 5.24 0.00 0.00

8 4420 2.5 139 6 13 2.3 0.3 0.5 1.72 0.00 0.00 4.13 5.24 5.24 0.00 0.00

6 5330 2.3 140 6 13 2.3 0.3 0.5 1.72 0.00 0.00 4.13 5.24 5.24 0.00 0.00

12 3050 2.8 143 6 13 2.6 0.3 0.5 1.72 0.00 0.00 4.13 5.66 5.66 0.00 0.00

10 3560 2.8 138 6 13 2.3 0.3 0.5 1.72 0.00 0.00 4.13 5.24 5.24 0.00 0.00

15 2670 2.9 144 6 15 3.2 0.5 0.4 1.72 0.00 0.00 4 .13 5.66 5.66 0.00 0.00

20 2030 3.2 145 6 19 4.2 0.7 0.1 1.72 0.00 0.00 4.13 5.66 5.66 0.00 0.00

22 1650 3.2 152 6 19 5.3 0.8 0.1 1.72 0.00 0.00 4 .13 5.66 5.66 0.00 0.00

25 1270 3.3 158 6 19 6.4 1.0 0.1 1.72 0.00 0.00 4.13 5.66 5.66 0.00 0.00

32 970 3.7 160 6 13 7.2 1.3 0.1 1.72 0.00 0.00 4.13 5.66 5.66 0.00 0.00

30 1040 3.6 159 6 15 7.0 1.2 0.1 1.72 0.00 0.00 4.13 5.66 5.66 0.00 0.00

45 430 5.3 173 6 13 7. 4 1.3 0.1 1.72 0.00 0.00 4.13 5.66 5.66 0.00 0.00

38 640 4.6 170 6 13 8.1 1.3 0.1 1.72 0.00 0.00 4.13 5.66 5.66 0.00 0.00

50 280 5.7 187 6 19 11. 4 1.5 0.1 1.72 0.00 0.00 4 .13 5.66 5.66 0.00 0.00

56 114

PicNo NCode

ESAB Welding and Cutting Products

Version 4.5 released on 13May13

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Carbon Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 260

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

First Row Mark Amp: 12

Thick-

Speed

ness

mm/m

25 2540 0.0 70 4 4 4.1 0.0 0.1 2.07 2.07 0.00 0.00 2.00 2.00 0.00 0.00

Version 4.5 released on 13May13

53 127

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

PRODUCTION

Material Carbon Steel

Gas Select 2

ESAB Welding and Cutting Products

Amperes 260

Cut Gas O2

Start Gas AIR

Shield Gas-1 AIR

Shield Gas-2 O2

AHC

Delay

Pierce

ting

Cut-

Height

Pierce

Height

Initial

Height

Arc

Volt-

Kerf

Speed

mm/m

ness

NOTE: Piercing not recommended on thicknesses greater than 38 mm Pierce delay indicated for edge starts greater than 38 mm

Thick-

sec

age

10 4320 3.2 135 5 4 3.8 0.6 0.1 1.72 0.00 0.00 4.13 7. 08 7.0 8 0.00 0.00

12 3680 3.8 137 6 13 5.1 0.6 0.1 1.72 0.00 0.00 4 .13 7. 08 7. 08 0.00 0.00

15 3300 3.8 141 6 13 5.1 0.6 0.1 1.72 0.00 0.00 4.13 7.0 8 7. 08 0.00 0.00

16 3200 3.8 142 6 13 5.1 0.6 0.1 1.72 0.00 0.00 4.13 7.0 8 7. 08 0.00 0.00

20 2290 4.1 145 6 13 5.1 0.6 0.1 1.72 0.00 0.00 4.13 7. 08 7.0 8 0.00 0.00

22 1980 4.4 14 6 6 13 5.1 0.5 0.1 1.72 0.00 0.00 4.13 7.0 8 7. 08 0.00 0.00

25 1650 4.4 148 6 13 5.1 1.0 0.1 1.72 0.00 0.00 4 .13 7. 08 7. 08 0.00 0.00

32 114 0 4.4 154 4 13 5.1 1.5 0.1 1.72 0.00 0.00 4.13 7.0 8 7. 08 0.00 0.00

30 128 0 4.4 152 5 13 5.1 1.2 0.1 1.72 0.00 0.00 4.13 7. 08 7.0 8 0.00 0.00

35 1070 5.1 155 4 15 7. 0 1.5 0.1 1.72 0.00 0.00 4.13 7.0 8 7. 08 0.00 0.00

38 960 5.1 158 4 15 7. 0 1.5 0.1 1.72 0.00 0.00 4.13 7.0 8 7. 08 0.00 0.00

Version 4.5 released on 13May13

45 660 5.1 167 4 15 8.7 1.5 0.1 1.72 0.00 0.00 4.13 7.0 8 7. 08 0.00 0.00

40 890 5.1 160 4 15 7.4 1.5 0.1 1.72 0.00 0.00 4.13 7.0 8 7. 08 0.00 0.00

55 360 5.5 179 4 15 10.7 1. 5 0.1 1.72 0.00 0.00 4.13 7.0 8 7. 08 0.00 0.00

50 410 5.1 175 4 15 10.2 1.5 0.1 1.72 0.00 0.00 4.13 7.0 8 7. 08 0.00 0.00

65 250 6.4 188 4 15 11. 7 1.5 0.1 1.72 0.00 0.00 4.13 7. 08 7.0 8 0.00 0.00

53 127

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Carbon Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 300

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

5 115

PicNo NCode

25 2540 0.0 70 4 4 4.1 0.0 0.1 2.07 2.07 0.00 0.00 2.00 2.00 0.00 0.00

Version 4.5 released on 13May13

ness

First Row Mark Amp: 20

Thick-

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

PRODUCTION

Speed

mm/m

Material Carbon Steel

Gas Select 9

Amperes 300

Start Gas N2

Cut Gas O2

Shield Gas-1 AIR

Shield Gas-2 NONE

NOTE: Piercing not recommended on thicknesses greater than 45 mm Pierce delay indicated for edge starts greater than 45 mm

ness

Thick-

6 4830 3.0 135 4 6 6.4 0.0 0.3 1.72 0.00 0.00 2.96 5.66 5.66 0.00 0.00

8 4690 3.1 140 4 7 7.3 0.3 0.3 1.72 0.00 0.00 2.96 5.66 5.66 0.00 0.00

12 3560 3.3 145 4 9 8.8 0.5 0.3 1.72 0.00 0.00 2.96 5.66 5.66 0.00 0.00

10 4570 3.2 145 4 8 8.1 0.5 0.3 1.72 0.00 0.00 2.96 5.66 5.66 0.00 0.00

15 3260 3.0 150 4 10 9.8 0.5 0.5 1.72 0.00 0.00 2.96 5.66 5.66 0.00 0.00

16 3180 2.9 151 4 10 10. 2 0.5 0.5 1.72 0.00 0.00 2.96 5.66 5.66 0.00 0.00

20 2410 3.6 153 4 11 10.6 0.7 0.6 1.72 0.00 0.00 2.96 5.66 5.66 0.00 0.00

25 178 0 4 .1 160 4 14 13. 5 0.6 0.7 1.72 0.00 0.00 2.96 5.66 5.66 0.00 0.00

32 114 0 4.3 170 4 15 15. 2 1.3 0.7 1.72 0.00 0.00 3.17 5.66 5.66 0.00 0.00

30 1320 4.2 167 4 15 14. 8 1.1 0.7 1.72 0.00 0.00 3 .11 5.66 5.66 0.00 0.00

35 1020 4.1 173 4 16 15.7 1.5 0.7 1.72 0.00 0.00 3 .17 5.66 5.66 0.00 0.00

38 890 4.8 175 4 16 15.6 1.7 0.7 1.72 0.00 0.00 2.96 5.09 5.09 0.00 0.00

45 610 4.8 182 4 18 18.0 2.0 0.8 1.72 0.00 0.00 3 .17 5.09 5.09 0.00 0.00

40 760 4.8 180 4 17 17.0 1.8 0.8 1.72 0.00 0.00 3.17 5.09 5.09 0.00 0.00

5 115

PicNo NCode

ESAB Welding and Cutting Products

Version 4.5 released on 13May13

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Carbon Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 300

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

5 120

PicNo NCode

25 2540 0.0 70 4 4 4.1 0.0 0.1 2.07 2.07 0.00 0.00 2.00 2.00 0.00 0.00

Version 4.5 released on 13May13

ness

First Row Mark Amp: 20

Thick-

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

SEVER

Material Carbon Steel

Gas Select 9

ESAB Welding and Cutting Products

Amperes 300

Start Gas N2

Cut Gas O2

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

ness

NOTE: Piercing not recommended on thicknesses greater than 45 mm Pierce delay indicated for edge starts greater than 45 mm

Thick-

6 6100 2.8 135 4 6 5.1 0.4 0.1 1.72 0.00 0.00 3.10 5.66 5.66 0.00 0.00

12 4320 2.0 150 4 12 12. 2 0.5 0.2 1.72 0.00 0.00 2.96 4.53 4.53 0.00 0.00

10 5080 3.2 145 4 8 8.1 0.5 0.1 1.72 0.00 0.00 2.96 5.66 5.66 0.00 0.00

16 3810 3.6 155 4 11 10.9 0.5 0.6 1.72 0.00 0.00 2.96 4.53 4.53 0.00 0.00

20 3050 3.6 160 4 14 13. 8 0.5 0.6 1.72 0.00 0.00 2.96 4.53 4.53 0.00 0.00

32 1900 5.3 165 4 14 14.0 1.0 0.6 1.72 0.00 0.00 2.96 4.53 4.53 0.00 0.00

35 1700 6.0 170 4 30 16.0 1.2 0.6 1.72 0.00 0.00 2.96 4.53 4.53 0.00 0.00

25 3050 3.6 160 4 14 14. 5 0.7 0.6 1.72 0.00 0.00 2.96 4.53 4.53 0.00 0.00

38 1520 7. 0 177 4 30 16.0 1.3 0.6 1.72 0.00 0.00 2.96 4.53 4.53 0.00 0.00

Version 4.5 released on 13May13

45 1020 7. 5 185 4 30 17.0 1. 8 0.6 1.72 0.00 0.00 2.96 4.53 4.53 0.00 0.00

40 1320 7.0 181 4 30 17. 0 1.6 0.6 1.72 0.00 0.00 2.96 4.53 4.53 0.00 0.00

5 120

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Carbon Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 360

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

25 2540 0.0 62 4 4 4.1 0.0 0.1 2.07 2.07 0.00 0.00 2.00 2.00 0.00 0.00

ness

First Row Mark Amp: 18 Second Row Mark Amp: 18

Thick-

25 5080 0.0 62 4 4 4.1 0.0 0.1 2.07 2.07 0.00 0.00 2.00 2.00 0.00 0.00

Version 4.5 released on 13May13

55 116

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

PRODUCTION

Speed

mm/m

Material Carbon Steel

Gas Select 2

Amperes 360

Cut Gas O2

Start Gas AIR

Shield Gas-1 AIR

Shield Gas-2 O2

ness

NOTE: Piercing not recommended on thicknesses greater than 50 mm Pierce delay indicated for edge starts greater than 50 mm

Thick-

12 4320 3.4 150 4 5 4.1 0.5 0.2 1.03 0.00 0.00 4.13 5.66 5.66 0.00 0.00

15 3950 3.4 150 4 5 5.2 0.5 0.2 1.03 0.00 0.00 4 .13 5.66 5.66 0.00 0.00

16 3810 3.4 150 4 5 5.6 0.5 0.2 1.03 0.00 0.00 4.13 5.66 5.66 0.00 0.00

20 2920 3.8 145 4 13 4.6 0.7 0.2 1.03 0.00 0.00 4.13 5.66 5.66 0.00 0.00

25 2160 4.2 150 4 13 4.6 0.7 0.2 1.03 0.00 0.00 4.13 5.66 5.66 0.00 0.00

32 1650 4.8 155 4 13 5.1 1.5 0.2 1.03 0.00 0.00 4.13 5.66 5.66 0.00 0.00

30 179 0 4.6 154 4 13 5.0 1.3 0.2 1.03 0.00 0.00 4.13 5.66 5.66 0.00 0.00

35 14 0 0 4.8 158 4 13 5.1 1.5 0.2 1.03 0.00 0.00 4.13 5.66 5.66 0.00 0.00

38 12 2 0 4.8 158 4 16 5.1 1.5 0.2 1.03 0.00 0.00 4.13 7.0 8 7. 08 0.00 0.00

45 970 4.8 160 4 21 16.0 2.3 0.2 1.03 0.00 0.00 3.76 7.84 7. 08 0.00 0.00

40 116 0 4.8 159 4 17 7. 9 1.7 0.2 1.03 0.00 0.00 4.03 7. 28 7.0 8 0.00 0.00

55 640 5.7 175 10 10 10.2 3.0 0.2 1.03 0.00 0.00 3.45 7. 08 7. 08 0.00 0.00

50 760 4.8 162 4 25 25.4 3.0 0.2 1.03 0.00 0.00 3.45 8.49 7. 08 0.00 0.00

75 200 6.7 200 10 10 10.2 3.0 0.2 1.03 0.00 0.00 3.45 5.66 5.66 0.00 0.00

65 460 6.4 180 10 10 10.2 3.0 0.2 1.03 0.00 0.00 3.45 5.66 5.66 0.00 0.00

55 116

PicNo NCode

ESAB Welding and Cutting Products

Version 4.5 released on 13May13

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Carbon Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 400

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

32 117

PicNo NCode

25 2540 0.0 52 4 4 4 .1 0.0 0 .1 2.07 2.07 0.00 0.00 2.00 2.00 0.00 0.00

Version 4.5 released on 13May13

ness

First Row Mark Amp: 18

Thick-

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

PRODUCTION

Material Carbon Steel

Gas Select 1

ESAB Welding and Cutting Products

Amperes 400

Start Gas N2

Cut Gas O2

Shield Gas-1 N2

Shield Gas-2 O2

AHC

Delay

Pierce

ting

Cut-

Height

Pierce

Height

Initial

Height

Arc

Volt-

Kerf

Speed

mm/m

ness

NOTE: Piercing not recommended on thicknesses greater than 50 mm Pierce delay indicated for edge starts greater than 50 mm

Thick-

sec

age

6 6600 3.3 130 4 13 4.2 0.4 0.3 1.03 0.00 0.00 2.41 4.25 4.25 3.54 3.54

8 5680 3.6 130 4 13 4.5 0.4 0.3 1.03 0.00 0.00 2.41 4.25 4.25 3.54 3.54

12 4190 4.1 132 4 13 3.8 0.4 0.3 1.03 0.00 0.00 2.76 4.25 4.25 3.54 3.54

15 3700 4.3 13 4 4 18 5.4 0.4 0.2 1.03 0.00 0.00 2.49 4.25 4.25 3.54 3.54

10 4830 3.8 130 4 13 4.8 0.4 0.3 1.03 0.00 0.00 2 .41 4.25 4.25 3.54 3.54

16 3560 4.3 135 4 19 5.8 0.4 0.2 1.03 0.00 0.00 2.41 4.25 4.25 3.54 3.54

20 2920 4.3 136 4 19 4.7 0.3 0.5 1.03 0.00 0.00 2.41 4.25 4.25 3.54 3.54

25 2030 5.5 145 4 19 6.2 0.8 0.6 1.03 0.00 0.00 2.76 4.25 4.25 3.54 3.54

32 1270 5.6 160 4 19 11. 4 0.8 0.6 1.03 0.00 0.00 2.76 4.25 4.25 3.54 3.54

35 114 0 5.6 165 4 25 11.4 0.8 0.6 1.03 0.00 0.00 2.76 4.25 4.25 3.54 3.54

30 1480 5.6 156 4 19 10.0 0.8 0.6 1.03 0.00 0.00 2.76 4.25 4.25 3.54 3.54

Version 4.5 released on 13May13

38 1070 5.8 167 4 19 11.4 1.0 0.6 1.03 0.00 0.00 2.76 4.25 4.25 3.54 3.54

45 760 5.8 170 4 19 12.7 1.5 0.6 1.03 0.00 0.00 2.76 4.25 4.25 3.54 3.54

40 890 5.8 168 4 25 12 .2 1.3 0.6 1.03 0.00 0.00 2.76 4.25 4.25 3.54 3.54

55 460 8.2 193 4 20 17. 6 2.5 0.6 1.03 0.00 0.00 2.87 4.25 4.25 3.54 3.54

50 560 7.1 185 4 19 16.3 2.0 0.6 1.03 0.00 0.00 2.76 4.25 4.25 3.54 3.54

65 250 10.4 210 4 23 20.3 3.5 0.6 1.03 0.00 0.00 3.10 4.25 4.25 3.54 3.54

32 117

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Carbon Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 450

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

39 129

PicNo NCode

25 2540 0.0 65 4 4 4 .1 0.0 0.1 2.07 2.07 0.00 0.00 2.01 2.01 0.00 0.00

Version 4.5 released on 13May13

ness

First Row Mark Amp: 25

Thick-

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

PRODUCTION

Material Carbon Steel

Gas Select 9

ESAB Welding and Cutting Products

Amperes 450

Start Gas N2

Cut Gas O2

Shield Gas-1 AIR

Shield Gas-2 NONE

AHC

Delay

Pierce

ting

Cut-

Height

Pierce

Height

Initial

Height

Arc

Volt-

Kerf

Speed

mm/m

ness

NOTE: Piercing not recommended on thicknesses greater than 50 mm Pierce delay indicated for edge starts greater than 50 mm

Thick-

sec

age

20 3000 3.8 137 5 10 6.0 0.8 0.3 1.03 0.00 0.00 3.31 7. 00 7. 00 0.00 0.00

32 1780 3.6 150 4 19 6.9 1.5 0.2 1.03 0.00 0.00 3.10 4.25 4.25 0.00 0.00

22 2540 3.9 140 5 10 6.4 1. 5 0.3 1.03 0.00 0.00 3.31 7. 00 7.0 0 0.00 0.00

30 1940 3.4 149 4 19 6.9 1.3 0.2 1.03 0.00 0.00 3.10 4.25 4.25 0.00 0.00

25 2360 3.0 145 4 19 7.0 0.8 0.2 1.03 0.00 0.00 3.10 4.25 4.25 0.00 0.00

35 1580 3.8 153 4 19 7. 2 1.8 0.2 1.03 0.00 0.00 3.10 5.69 5.69 0.00 0.00

38 1400 4.1 155 4 19 7. 6 2.0 0.2 1.03 0.00 0.00 3.10 7.0 8 7. 08 0.00 0.00

45 114 0 4.2 160 4 19 8.6 2.5 0.2 1.03 0.00 0.00 3.10 7.0 8 7. 08 0.00 0.00

40 1320 4 .1 156 4 19 7.9 2.2 0.2 1.03 0.00 0.00 3.10 7.0 8 7. 08 0.00 0.00

Version 4.5 released on 13May13

55 690 5.7 172 4 19 11. 3 3.5 0.2 1.03 0.00 0.00 3.10 7.0 8 7. 08 0.00 0.00

50 840 5.1 165 4 19 10.2 3.5 0.2 1.03 0.00 0.00 3.10 7. 08 7. 0 8 0.00 0.00

75 250 8.0 185 4 19 13.7 3.5 0.2 1.03 0.00 0.00 3.45 5.66 5.66 0.00 0.00

65 560 6.4 180 4 19 12 .5 3.5 0.2 1.03 0.00 0.00 3.45 5.66 5.66 0.00 0.00

39 129

PicNo NCode

Aluminum

Production

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

PRODUCTION

Speed

mm/m

Material Aluminum

Gas Select 3

Amperes 35

Start Gas N2

Cut Gas N2

Shield Gas-1 N2

Shield Gas-2 NONE

ness

Thick-

1 6100 1.8 160 4 3 3.0 0.1 0.4 0.00 0.00 2.07 5.86 2.26 2.26 0.00 0.00

3 3560 1. 5 165 4 3 3.0 0.1 0.4 0.00 0.00 2.07 5.86 1.98 1.98 0.00 0.00

2 5080 1. 5 160 4 3 3.0 0.1 0.4 0.00 0.00 2.07 5.86 2.26 2.26 0.00 0.00

18 171

PicNo NCode

ESAB Welding and Cutting Products

Version 4.5 released on 13May13

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

PRODUCTION

Speed

mm/m

Material Aluminum

Gas Select 3

Amperes 50

Start Gas N2

Cut Gas N2

Shield Gas-1 N2

Shield Gas-2 NONE

ness

Thick-

2 4750 1.3 168 4 4 3.8 0.2 0.8 0.00 0.00 1.72 5.51 4.25 4.25 0.00 0.00

3 4060 1.3 172 4 4 4.0 0.2 0.8 0.00 0.00 1.72 5.51 4.25 4.25 0.00 0.00

5 2160 1. 3 180 4 4 4.2 0.2 0.8 0.00 0.00 1.72 5.51 4.25 4.25 0.00 0.00

4 3050 1. 3 176 4 4 4.1 0.2 0.8 0.00 0.00 1.72 5. 51 4.25 4.25 0.00 0.00

6 1900 1.5 188 4 6 6.4 0.2 0.8 0.00 0.00 1.72 5. 51 4.25 4.25 0.00 0.00

7 172

PicNo NCode

ESAB Welding and Cutting Products

Version 4.5 released on 13May13

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

PRODUCTION

Speed

mm/m

Material Aluminum

Gas Select 3

Amperes 100

Start Gas N2

Cut Gas N2

Shield Gas-1 N2

Shield Gas-2 NONE

ness

Thick-

6 2030 1.7 153 4 4 4.1 0.7 0.5 0.00 0.00 1.38 2.76 4.81 4.81 0.00 0.00

8 1970 1.7 154 4 4 4.3 0.6 0.7 0.00 0.00 1.38 2.76 3.85 3.85 0.00 0.00

12 1270 1.1 160 4 6 4.8 0.6 0.8 0.00 0.00 1. 38 2.76 2.97 2.97 0.00 0.00

10 1900 1.7 155 4 5 4.6 0.6 0.8 0.00 0.00 1.38 2.76 2.97 2.97 0.00 0.00

8 173

PicNo NCode

ESAB Welding and Cutting Products

Version 4.5 released on 13May13

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

PRODUCTION

Speed

mm/m

Material Aluminum

Gas Select 3

Amperes 200

Start Gas N2

Cut Gas N2

Shield Gas-1 N2

Shield Gas-2 NONE

ness

Thick-

6 3180 2.5 140 4 6 2.9 0.4 0.6 0.00 0.00 0.69 3.17 4.10 4.10 0.00 0.00

8 2910 2.5 143 4 6 3.0 0.5 0.6 0.00 0.00 0.69 3.17 4 .10 4.10 0.00 0.00

12 2160 2.4 162 4 6 5.5 0.5 0.6 0.00 0.00 0.69 3.17 4.10 4.10 0.00 0.00

15 1730 2.5 168 4 11 6.6 0.5 0.6 0.00 0.00 0.69 3.17 4 .10 4.10 0.00 0.00

10 2670 2.5 145 4 6 3.0 0.5 0.6 0.00 0.00 0.69 3.17 4 .10 4.10 0.00 0.00

16 1570 2.6 170 4 13 7. 0 0.5 0.6 0.00 0.00 0.69 3.17 4 .10 4.10 0.00 0.00

20 1020 2.8 180 4 13 8.4 0.5 0.6 0.00 0.00 0.69 3.17 4.10 4.10 0.00 0.00

25 690 3.0 192 4 13 6.9 0.7 0.9 0.00 0.00 0.69 3.17 4.53 4.53 0.00 0.00

32 510 4.0 192 4 13 9.5 1.1 1.1 0.00 0.00 0.69 3.17 4.10 4.10 0.00 0.00

35 430 4.6 193 4 10 9.7 1.1 1.1 0.00 0.00 0.69 2.76 2.83 2.83 0.00 0.00

30 560 3.7 192 4 13 8.8 1.0 1.0 0.00 0.00 0.69 3 .17 4.22 4.22 0.00 0.00

38 380 4.6 195 4 10 9.7 0.5 0.6 0.00 0.00 0.69 2.76 2.83 2.83 0.00 0.00

9 174

PicNo NCode

ESAB Welding and Cutting Products

Version 4.5 released on 13May13

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

PRODUCTION

Speed

mm/m

Material Aluminum

Gas Select 3

Amperes 260

Start Gas N2

Cut Gas N2

Shield Gas-1 N2

Shield Gas-2 NONE

ness

Thick-

6 7620 2.8 160 4 6 5.8 0.5 0.6 0.00 0.00 0.48 3.45 4.10 4.10 0.00 0.00

8 6300 2.8 163 4 7 6.4 0.5 0.6 0.00 0.00 0.48 3.45 4.10 4.10 0.00 0.00

12 3810 2.8 168 4 8 7. 6 0.5 0.6 0.00 0.00 0.48 3.45 4.10 4.10 0.00 0.00

10 5080 2.8 165 4 7 6.9 0.5 0.6 0.00 0.00 0.48 3.45 4.10 4.10 0.00 0.00

15 3260 2.8 172 4 9 8.4 0.5 0.3 0.00 0.00 0.48 3.45 4.10 4.10 0.00 0.00

16 3050 2.8 174 4 10 8.6 0.5 0.2 0.00 0.00 0.48 3.45 4.10 4.10 0.00 0.00

20 2290 2.8 180 4 10 9.7 0.5 0.6 0.00 0.00 0.48 3.45 4.10 4.10 0.00 0.00

25 1140 2.8 192 4 13 9.7 0.5 0.6 0.00 0.00 0.48 3.45 4.10 4.10 0.00 0.00

32 640 3.6 194 4 25 9.4 1.5 0.2 0.00 0.00 0.48 3.45 4.10 4.10 0.00 0.00

30 780 3.3 193 4 22 9.5 1.2 0.3 0.00 0.00 0.48 3.45 4.10 4.10 0.00 0.00

10 175

PicNo NCode

ESAB Welding and Cutting Products

Version 4.5 released on 13May13

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

PRODUCTION

Speed

mm/m

Material Aluminum

Gas Select 3

Amperes 360

Start Gas N2

Cut Gas N2

Shield Gas-1 N2

Shield Gas-2 NONE

ness

Thick-

6 5840 3.0 147 4 6 2.8 0.0 0.2 0.00 0.00 0.69 2.76 8.49 8.49 0.00 0.00

8 5180 3.2 151 4 10 3.9 0.1 0.2 0.00 0.00 0.69 2.76 8.49 8.49 0.00 0.00

12 4060 3.3 160 4 16 6.4 0.2 0.2 0.00 0.00 0.69 2.76 8.49 8.49 0.00 0.00

15 3420 3.4 163 4 17 7.2 0.2 0.2 0.00 0.00 0.69 2.76 8.49 8.49 0.00 0.00

10 4570 3.3 155 4 13 5.0 0.2 0.2 0.00 0.00 0.69 2.76 8.49 8.49 0.00 0.00

16 3180 3.4 16 4 4 18 7. 5 0.2 0.2 0.00 0.00 0.69 2.76 8.49 8.49 0.00 0.00

20 2290 3.6 168 4 18 8.6 0.2 0.2 0.00 0.00 0.69 2.76 8.49 8.49 0.00 0.00

25 1400 3.8 180 4 20 11. 2 0.5 0.2 0.00 0.00 0.69 2.76 5.66 5.66 0.00 0.00

32 890 5.1 190 4 25 10.7 0.5 0.2 0.00 0.00 0.69 2.76 5.66 5.66 0.00 0.00

30 1030 4.7 187 4 24 10.8 0.5 0.2 0.00 0.00 0.69 2.76 5.66 5.66 0.00 0.00

11 176

PicNo NCode

ESAB Welding and Cutting Products

Version 4.5 released on 13May13

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

PRODUCTION

Speed

mm/m

Gas Select 10

Material Aluminum

Amperes 450

Start Gas N2

Cut Gas N2

Shield Gas-1 AIR

Shield Gas-2 NONE

NOTE: Piercing not recommended on thicknesses greater than 38 mm Pierce delay indicated for edge starts greater than 38 mm

ness

Thick-

12 4830 3.7 160 4 13 7.9 1.0 0.2 0.00 0.00 0.34 2.76 5.66 5.66 0.00 0.00

15 4180 3.8 162 4 13 8.2 1.0 0.2 0.00 0.00 0.34 2.76 5.66 5.66 0.00 0.00

16 3940 3.8 163 4 13 8.4 1.0 0.2 0.00 0.00 0.34 2.76 5.66 5.66 0.00 0.00

20 3180 4.3 170 4 13 8.9 1.0 0.2 0.00 0.00 0.34 2.76 5.66 5.66 0.00 0.00

25 2030 4.4 175 4 13 8.9 1.0 0.2 0.00 0.00 0.34 2.76 5.66 5.66 0.00 0.00

32 1400 4.7 180 4 18 9.4 1.3 0.2 0.00 0.00 0.34 2.76 5.66 5.66 0.00 0.00

30 1570 4.6 179 4 16 9.3 1.2 0.2 0.00 0.00 0.34 2.76 5.66 5.66 0.00 0.00

35 1200 5.2 183 4 18 9.7 1.4 0.2 0.00 0.00 0.34 2.76 5.66 5.66 0.00 0.00

38 1020 5.6 185 4 18 9.9 1.5 0.2 0.00 0.00 0.34 2.76 5.66 5.66 0.00 0.00

45 760 6.4 19 0 4 18 9.9 1.5 0.2 0.00 0.00 0.34 2.76 5.66 5.66 0.00 0.00

40 940 5.8 186 4 18 9.9 1.5 0.2 0.00 0.00 0.34 2.76 5.66 5.66 0.00 0.00

50 510 7. 2 200 4 18 10. 2 1. 5 0.5 0.00 0.00 0.34 2.76 5.66 5.66 0.00 0.00

14 179

PicNo NCode

ESAB Welding and Cutting Products

Version 4.5 released on 13May13

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

PRODUCTION

Speed

mm/m

Material Aluminum

Gas Select 5

Amperes 600

Start Gas N2

Cut Gas H35

Shield Gas-1 N2

Shield Gas-2 NONE

NOTE: Piercing not recommended on thicknesses greater than 50 mm Pierce delay indicated for edge starts greater than 50 mm

ness

Thick-

25 2290 7.6 172 4 20 12.7 0.5 0.3 0.00 3.10 0.69 0.00 9.91 9.91 0.00 0.00

32 2090 7. 5 17 3 4 20 13. 8 0.6 0.3 0.00 3.10 0.69 0.00 9.91 9.91 0.00 0.00

30 2150 7. 5 173 4 20 13.4 0.6 0.3 0.00 3.10 0.69 0.00 9.91 9.91 0.00 0.00

35 2000 7.4 174 4 20 14. 2 0.7 0.3 0.00 3.10 0.69 0.00 9.91 9.91 0.00 0.00

38 1900 7.4 175 4 20 14.7 0.8 0.3 0.00 3.10 0.69 0.00 9.91 9.91 0.00 0.00

45 1490 8.2 186 4 23 17.1 0.9 0.3 0.00 3.10 0.69 0.00 9.91 9.91 0.00 0.00

40 1790 7. 6 17 8 4 21 15.4 0.8 0.3 0.00 3.10 0.69 0.00 9.91 9.91 0.00 0.00

75 640 10.5 215 4 25 23.6 1.5 0.3 0.00 3.10 0.69 0.00 9.91 9.91 0.00 0.00

50 114 0 8.9 195 4 25 19.1 1.0 0.3 0.00 3.10 0.69 0.00 9.91 9.91 0.00 0.00

12 17 7

PicNo NCode

ESAB Welding and Cutting Products

Version 4.5 released on 13May13

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

Creep speed 1/2 cut speed rst 12 mm

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

PRODUCTION

Speed

mm/m

Material Aluminum

Gas Select 4

Amperes 600

Start Gas N2

Cut Gas H35

Shield Gas-1 AIR

Shield Gas-2 NONE

NOTE: Piercing not recommended on thicknesses greater than 76 mm Pierce delay indicated for edge starts greater than 76 mm

ness

Thick-

75 640 11. 3 170 13 19 13.7 1.7 0.3 0.00 1.72 0.41 0.00 7.0 8 7. 08 0.00 0.00

125 300 15.7 215 13 32 35.3 5.0 1.5 0.00 1.72 0.41 0.00 6. 51 6. 51 0.00 0.00

100 380 20.6 200 13 32 29.2 3.0 1.5 0.00 1.72 0.41 0.00 5.09 5.09 0.00 0.00

150 200 19.3 230 13 32 35.6 5.0 1. 5 0.00 1.72 0.41 0.00 6.51 6. 51 0.00 0.00

15 178

PicNo NCode

ESAB Welding and Cutting Products

Version 4.5 released on 13May13

Stainless Steel

Production

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Stainless Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 70

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

Speed

mm/m

25 10160 0.0 85 3 2 1.6 0.0 0.1 5.18 5.18 0.00 0.00 4.00 4.00 0.00 0.00

25 2540 0.0 85 3 2 1.6 0.0 0.1 5.18 5.18 0.00 0.00 4.00 4.00 0.00 0.00

Version 4.5 released on 13May13

ness

First Row Mark Amp: 14 Second Row Mark Amp: 14

Thick-

16 141

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

PRODUCTION

Speed

mm/m

Material Stainless Steel

Gas Select 3

Amperes 70

Start Gas N2

Cut Gas N2

Shield Gas-1 N2

Shield Gas-2 NONE

ness

Thick-

1 6980 1.0 14 0 4 4 2.0 0.0 0.1 0.00 0.00 1.72 3.45 9.91 9.91 0.00 0.00

2 6100 1.3 140 4 4 2.0 0.0 0.2 0.00 0.00 1.72 3.45 9.91 9.91 0.00 0.00

3 3300 1. 3 14 6 4 4 2.8 0.0 0.4 0.00 0.00 1.72 3.45 9.91 9.91 0.00 0.00

4 2540 1.3 148 4 4 3.0 0.0 0.4 0.00 0.00 1.72 3.45 9.91 9.91 0.00 0.00

5 178 0 1.3 150 4 4 3.0 0.0 0.4 0.00 0.00 1.72 3.45 9.91 9.91 0.00 0.00

16 141

PicNo NCode

ESAB Welding and Cutting Products

Version 4.5 released on 13May13

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

MARKING

Material Stainless Steel

Gas Select 6

ESAB Welding and Cutting Products

Amperes 130

Cut Gas ARG

Start Gas ARG

Shield Gas-1 AIR

Shield Gas-2 NONE

First Row Mark Amp: 18

Thick-

Speed

ness

mm/m

25 2540 0.0 80 4 4 4.1 0.0 0.1 3.59 3.59 0.00 0.00 4.00 4.00 0.00 0.00

Version 4.5 released on 13May13

8 142

PicNo NCode

Cut

CMH

Start

CMH

Cut

CMH

Start

bar

Cut

bar

Start

bar

Cut

bar

Plasma Gas PG-1 Plasma Gas PG-2 Shield Gas SG-1 Shield Gas SG-2

Start

sec

AHC

Delay

sec

Delay

Pierce

ting

Cut-

Pierce

Initial

Arc

Height

age

Volt-

Kerf

PRODUCTION

Speed

mm/m

Material Stainless Steel

Gas Select 3

Amperes 130

Start Gas N2

Cut Gas N2

Shield Gas-1 N2

Shield Gas-2 NONE

ness

Thick-

6 2160 2.3 150 4 5 2.3 0.3 0.3 0.00 0.00 1.03 3.79 7. 36 7. 36 0.00 0.00

8 1630 2.5 153 4 5 2.7 0.4 0.3 0.00 0.00 1.03 3.79 6.48 6.48 0.00 0.00

12 760 2.7 160 4 5 3.2 0.6 0.3 0.00 0.00 1.03 3.79 4.25 4.25 0.00 0.00

15 700 2.7 168 4 11 4.6 0.7 0.3 0.00 0.00 1.03 3.79 4.03 4.03 0.00 0.00

10 114 0 2.7 155 4 5 3.0 0.5 0.3 0.00 0.00 1.03 3.79 5.66 5.66 0.00 0.00

16 690 2.7 170 4 13 5.1 0.7 0.3 0.00 0.00 1.03 3.79 3.96 3.96 0.00 0.00

20 640 2.8 180 4 13 7.6 0.9 0.3 0.00 0.00 1.03 3.79 3.96 3.96 0.00 0.00

8 142

PicNo NCode

ESAB Welding and Cutting Products

100

Version 4.5 released on 13May13

ESAB M3 Plasma PT-36 G2 Plasma System Cutting Data Instruction manual

Specifications and Main Features

Frequently Asked Questions

User Manual