Laser lamp kit
Instruction manual
0456 558 101 US 20190625
TABLE OF CONTENTS
1
SAFETY ....................................................................................................... 3
1.1 Meaning of symbols ............................................................................... 3
1.2 Safety precautions ................................................................................. 3
2
INTRODUCTION.......................................................................................... 6
3
TECHNICAL DATA ...................................................................................... 7
4
INSTALLATION............................................................................................ 8
4.1 General .................................................................................................... 8
4.2 Connecting the laser lamps to the PEK unit ........................................ 8
4.3 Connecting the laser lamps to the PEH unit ........................................ 9
4.4 Connecting the laser lamps to the EAC10 unit................................... 9
5
OPERATION ................................................................................................ 11
5.1 General .................................................................................................... 11
6
ORDERING SPARE PARTS ........................................................................ 12
ORDERING NUMBERS....................................................................................... 13
Rights reserved to alter specifications without notice.
0456 558 101 © ESAB AB 2019
1 SAFETY
1 SAFETY
1.1 Meaning of symbols
As used throughout this manual: Means Attention! Be Alert!
DANGER!
Means immediate hazards which, if not avoided, will result in immediate,
serious personal injury or loss of life.
WARNING!
Means potential hazards which could result in personal injury or loss of life.
CAUTION!
Means hazards which could result in minor personal injury.
WARNING!
Before use, read and understand the instruction manual
and follow all labels, employer's safety practices and
Safety Data Sheets (SDSs).
1.2 Safety precautions
WARNING!
EQUIPMENT MAINTENANCE
Faulty or improperly maintained equipment can cause injury or death.
Therefore:
1. Always have qualified personnel perform the installation, troubleshooting and
maintenance work. Do not perform any electrical work unless you are
qualified to perform such work.
2. Before performing any maintenance work inside a power source, disconnect
the power source from the incoming electrical power.
3. Maintain cables, earthing wire, connections, power cord and power supply in
safe working order. Do not operate any equipment in faulty condition.
4. Do not abuse any equipment or accessories. Keep equipment away from
heat sources such as furnaces, wet conditions such as water puddles, oil or
grease, corrosive atmospheres and inclement weather.
5. Keep all safety devices and cabinet covers in position and in good repair.
6. Use equipment only for its intended purpose. Do not modify it in any manner.
0456 558 101
- 3 -
© ESAB AB 2019
1 SAFETY
WARNING!
Failing to follow these instructions may result in risk of fire, electric shock or personal
injury.
• Only charge the correct type of rechargeable battery to reduce the risk of
explosion, personal injury or other damage.
• Do not open the charger. Any repairs should be done by the manufacturer or
authorized service personnel.
• Do not attempt to take the unit apart; this action voids the warranty. Do not
disassemble the unit when it is plugged into the mains electric supply to avoid
the risk of electric shock or fire.
• Do not use the charger if it is visibly damaged.
Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety
precautions must meet the requirements that apply to this type of equipment. The following
recommendations should be observed, in addition to the standard regulations that apply to
the workplace.
All work must be carried out by trained personnel well-acquainted with the operation of the
equipment. Incorrect operation of the equipment may lead to hazardous situations, which
could result in injury to the operator and damage to the equipment.
1. Anyone who uses the equipment must be familiar with:
○ its operation
○ the location of emergency stops
○ its function
○ the relevant safety precautions
○ welding and cutting or other applicable operation of the equipment
2. The operator must ensure that:
○ no unauthorized person is within the working area of the equipment when it is
started up
○ no-one is unprotected when the arc is struck or work is started with the
equipment
3. The workplace must:
○ be suitable for the purpose
○ be free from drafts
4. Personal safety equipment:
○ Always wear recommended personal safety equipment, such as safety glasses,
flame-proof clothing, safety gloves
○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which
could become trapped or cause burns
5. General precautions:
○ Make sure the return cable is connected securely
○ Work on high voltage equipment may only be carried out by a qualified
electrician
○ Appropriate fire extinguishing equipment must be clearly marked and close at
hand
○ Lubrication and maintenance must not be carried out on the equipment during
operation
CAUTION!
This product is intended for industrial use. In a domestic environment, this product
may cause radio interference. It is the user's responsibility to take adequate
precautions.
0456 558 101
- 4 -
© ESAB AB 2019
1 SAFETY
NOTE!
Dispose of electronic equipment at a recycling
facility!
To conform with the European Directive 2012/19/EC on
Waste Electrical and Electronic Equipment and its
implementation in accordance with national law,
electrical and/or electronic equipment that has reached
the end of its life must be disposed of at a recycling
facility.
As the person responsible for the equipment, it is your
responsibility to obtain information on approved
collection stations.
WARNING!
Laser radiation
• The laser radiation can injure your eyes. Do not look
straight at the laser diode or the laser beam when it is
activated (regardless of class rating).
• Do not direct the laser beam towards another person.
For further information contact the nearest ESAB dealer.
ESAB has an assortment of welding accessories and personal protection equipment
for purchase. For ordering information, contact your local ESAB dealer or visit us on
our website.
0456 558 101
- 5 -
© ESAB AB 2019
Loading...