ESAB Feed 3004 Aristo, Feed 4804Aristo Instruction Manual

GB

Valid for serial no. 620--xxx--xxxx0458 716 201 GB 071005

Feed 3004
Feed 4804

Aristot

Instruction manual

-- 2 --

TOCe

Rights reserved to alter specifications without notice.

1 DIRECTIVE 3........................................................

2SAFETY 3...........................................................

3 INTRODUCTION 5...................................................

3.1 Equipment 5................................................................

3.2 Control panel 5.............................................................

4 TECHNICAL DATA 6.................................................

5 INSTALLATION 7....................................................

5.1 Lifting instructions 7.........................................................

5.2 Terminating resistors 8.......................................................

5.3 Connection of multiple wire feed units 8........................................

6 OPERATION 9.......................................................

6.1 Connections and controls 10...................................................

6.2 Water connection 10..........................................................

6.3 Remote control unit 11........................................................

6.4 Wire feed pressure 1 1........................................................

6.5 Changing / loading wire Feed 3004 12..........................................

6.6 Changing / loading wire Feed 4804 12..........................................

6.7 Replacing the Feed 3004 feed rollers 12.........................................

6.8 Replacing the Feed 4804 feed rollers 13.........................................

7 MAINTENANCE 13....................................................

7.1 Inspection and cleaning 13....................................................

8 ORDERING OF SPARE PARTS 14......................................

DIAGRAM 16............................................................

ORDERING NUMBER 19.................................................

WEAR COMPONENTS 20.................................................

ACCESSORIES 24.......................................................

-- 3 --

bm29d1ea

1DIRECTIVE

DECLARATION OF CONFORMITY

ESAB AB, Welding Equipment, SE--695 81 Laxå, Sweden, declares that Wire feed unit Feed
3004/4804 from serial number 620 (2006 w.20) are constructed and tested in compliance with the
standard EN 60974--5 and EN 60974--10 in accordance with the requirements of directive
(2006/95/EC) and (2004/108/EEC).

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------

Kent Eimbrodt
Global Director
Equipment and Automation

Laxå 2007--03--14

2SAFETY

Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety precautions
must meet the requirements that apply to this type of welding equipment. The following recommen­dations should be observed in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well--acquainted with the operation of the welding
equipment. Incorrect operation of the equipment may lead to hazardous situations which can result
in injury to the operator and damage to the equipment.

1. Anyone who uses the welding equipment must be familiar with:

S its operation
S location of emergency stops
S its function
S relevant safety precautions
S welding

2. The operator must ensure that:

S no unauthorized person is stationed within the working area of the equipment when it is

started up.

S no--one is unprotected when the arc is struck

3. The workplace must:

S be suitable for the purpose
S be free from drafts

4. Personal safety equipment

S Always wear recommended personal safety equipment, such as safety glasses, flame--proof

clothing, safety gloves.

S Do not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become

trapped or cause burns.

5. General precautions

S Make sure the return cable is connected securely.
S Work on high voltage equipment may only be carried out by a qualified electrician.
S Appropriate fire extinquishing equipment must be clearly marked and close at hand.
S Lubrication and maintenance must not be carried out on the equipment during operation.

GB

-- 4 --

bm29d1ea

WARNING

READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.

ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE PRECAU­TIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE
BASED ON MANUFACTURERS’ HAZARD DATA.

ELECTRIC SHOCK -- Can kill

S Install and earth the welding unit in accordance with applicable standards.
S Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
S Insulate yourself from earth and the workpiece.
S Ensure your working stance is safe.

FUMES AND GASES -- Can be dangerous to health

S Keep your head out of the fumes.
S Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone

and the general area.

ARC RAYS -- Can injure eyes and burn skin.

S Protect your eyes and body. Use the correct welding screen and filter lens and wear protective

clothing.

S Protect bystanders with suitable screens or curtains.

FIRE HAZARD

S Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.

NOISE -- Excessive noise can damage hearing

S Protect your ears. Use earmuffs or other hearing protection.
S Warn bystanders of the risk.

MALFUNCTION -- Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

ESAB can provide you with all necessary welding protection an d accessories.

WARNING!

Read and understand the instruction manual before installing
or operating.

This product is solely intended for arc welding.

Do not dispose of electrical equipment together with normal waste!

In observance of European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment and its implementation in accordance with national law, electrical equipment
that has reached the end of its life must be collected separately and returned to an
environmentally compatible recycling facility. As the owner of the equipment, you should
get information on approved collection systems from our local representative.

By applying this European Directive you will improve the environment and human health!

GB

-- 5 --

bm29d1ea

3 INTRODUCTION

The Feed 3004 and Feed 4804 wire feed units are intended for use with Mig power
sources.

There are several variants available: see on page 19.

They are totally enclosed, containing four--wheel feeders and the necessary control
electronics.

They are suitable for use with wire on ESAB’s MarathonPact, or on standard
bobbins (standard Ø 300 mm, accessory Ø 440 mm).

The units can be positioned in a choice of ways: on the power source itself, hanging
above the working position, on a support arm or with a wheelset on the floor.

ESAB’s accessories for the product can be found on page 24.

3.1 Equipment

The unit Feed 3004 is supplied with:

S Instruction manual for the wire feed unit.

S Instruction manual for control panel.

S Stickers with recommended wear parts.

The unit Feed 4804 is supplied with:

S Distance washer (4 pieces).

S Hexagon key (4 mm)

S Instruction manual for the wire feed unit.

S Instruction manual for the control panel.

S Stickers with recommended wear parts.

3.2 Control panel

The units are supplied with one of the following control panels:

Empty panel for use with double wire feed units or
with use of control box U8.

MA4

With knobs for setting the voltage and wire feed
speed / current. Other settings by pushbuttons, with
corresponding symbols on the display panel.

GB

-- 6 --

bm29d1ea

MA6

With knobs for setting the voltage and wire feed
speed / current. Other settings by pushbuttons, with
text indication on the display panel.

U6

With knobs for setting the voltage and wire feed
speed / current. Other settings by pushbuttons, with
text indication on the display panel.

Detailed descriptions of the control panels can be found in separate Instruction
manuals.

4 TECHNICAL DATA

Feed 3004 Feed 4804
Power supply 42 V 50 -- 60 Hz 42 V 50 -- 60 Hz
Power requirement 336 V A 378 V A
Motor current 8A 9A
Wire feed speed 0.8 -- 25 m/min 0.8 -- 25 m/min
Welding gun connection EURO EURO
Max. diameter of wire bobbin 300 mm (*440 mm) 300 mm (*440 mm)
Wire dimension 0.6 -- 1.6 mm 0.6 -- 2.4 mm
Operating temperature -- 1 0 t o + 4 0 ˚C -- 1 0 t o + 4 0 ˚C
Weight

basic unit
with bobbin carrier
with enclosed bobbin carrier

13 kg

16 kg

17.5 kg

18 kg
21 kg

22.5 kg

Dimensions (l x w x h)

basic unit
with bobbin carrier
with enclosed bobbin carrier

380 x 265 x 340 mm

560 x 265 x 350 mm

690 x 285 x 420 mm

380 x 265 x 340 mm
560 x 265 x 350 mm
690 x 285 x 420 mm

Shielding gas

max pressure

All types intended for

MIG/MAG welding

0.5 MPa (5 bar)

All types intended for
MIG/MAG welding

0.5 MPa (5 bar)

Coolant

max pressure

50% water / 50% mono--ethylen

glycol

0.5 MPa (5 bar)

50% water / 50% mono--ethylen
glycol

0.5 MPa (5 bar)

Permissible load at

60% duty cycle

500 A 500 A

Enclosure class

basic unit
with bobbin carrier
with enclosed bobbin carrier

IP23

IP2X

IP23

IP23
IP2X
IP23

* Accessory, see page 24.

Duty cycle

The duty cycle refers to the time as a percentage of a ten--minute period that you can weld at a cer­tain load without overloading.

GB

-- 7 --

bm29d1ea

Enclosure class

The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid
objects or water. Equipment marked IP23 is designed for indoor and outdoor use.

Equipment marked IP2X is designed for indoor use.

5 INSTALLATION

The installation must be executed by a professional.

WARNING!

This product is intended for industrial use. In a domestic environment this product may cause radio
interference. It is the user’s responsibility to take adequate precautions.

WARNING!

When welding in an environment with increased electrical danger, only power sources intended
for this environment may be used. These power sources are marked with the symbol .

5.1 Lifting instructions

Ordering number for the lifting eye can be found on page 24.

Note! If another mounting device is used, this should be insulated from the wire feed
unit.

GB

-- 8 --

bm29d1ea

5.2 Terminating resistors

In order to avoid communication interference, the
ends of the CAN bus must be terminated by resistive
loads.

One end of the CAN bus is at the wire feed unit control panel,
which incorporates a terminating resistor. The other end is in
the power source and it must be fitted with a terminating resistor,
as shown in the diagram to the right.

5.3 Connection of multiple wire feed units

When connecting multiple wire feed units (maximum 4), use wire feed units without
control panel and with control box U8.

Two feed units are to be connected according to the picture.

When connecting more than two feed units, an authorised ESAB service technican
must perform the installation.

GB

-- 9 --

bm29d1ea

6 OPERATION

General safety regulations for the handling of the equipment can be found on
page 3. Read through before you start using the equipment!

WARNING!

Assure that the side panels are closed during operation.

To prevent the reel from sliding off the hub: Lock the reel in place by
turning the red knob as shown on the warning label attached next to
the hub.

WARNING!

WARNING!

Rotating parts can cause injury, take great care.

WARNING!

There is a risk of tipping if the wire feed unit is fitted with a counterbalance arm. Secure the
equipment, especially if used on an uneven or sloping surface.

When moving the equipment use intended handle. NOTE! Never pull on the gun.

GB

-- 1 0 --

bm29d1ea

6.1 Connections and controls

1 Control panel

(see respective instruction manual)

6 Connection for welding current from the

power source (OKC)

2a2bConnection for remote control

Connection for U8.

7 Connection for the control cable from the

power source

3 Connection with ELP* for cooling water to

the welding gun-- BLUE

8 Connection for cooling water to the power

source (cooling unit) -- RED

4 Connection for cooling water from the wel-

ding gun -- RED

9 Connection for cooling water from the po-

wer source (cooling unit) -- BLUE

5 Connection for the welding gun 10 Connection for protection gas

NOTE! Cooling water connections only available on certain models.
* ELP = ESAB Logic Pump, see point 6.2.

6.2 Water connection

The wire feed unit with water connection is equipped with a detection system ELP
(ESAB Logic Pump) which checks that the water hoses are connected.

Mig 4000i and Mig 5000i

The power unit On/Off switch must be in the “0” position (Off) when connecting a
water--cooled welding gun.

If a water--cooled welding gun is connected, the water pump starts automatically
when the m ain On/Off switch is turned to “START” and/or when welding starts. After
welding, the pump continues to run for 6,5 minutes, and then switches to the
energy--saving mode.

GB

-- 1 1 --

bm29d1ea

Mig 4500i

The power unit On/Off switch for cooling unit must be in the “I” position (ON) when
connecting a water--cooled welding gun.

6.3 Remote control unit

The program version in U8 should be 1.20 or higher. Machines with intergral control
panels should have program version 1.21 or higher, in order for the remote control to
function correctly.

When the remote control unit is connected, the power source and wire feed unit are
in remote control mode; the buttons and knobs are blocked. The functions can only
be adjusted via the remote unit.

If the remote control unit is not to be used, the remote control unit must be
disconnected from the power source / wire feed unit, as otherwise it will re main in
remote control m ode.

When a remote control unit is used to set the voltage, the function will be changed to
the setting of current during MMA welding.

For more information about the operation of the remote control unit, see the
operating instructions for the control panel.

6.4 Wire feed pressure

Start by making sure that the wire moves smoothly through the wire guide. Then
set the pressure of the wire feeder’s pressure rollers. It is important that the
pressure is not too great.

Fig 1 Fig 2

To check that the feed pressure is set correctly, you can feed out the wire against
an insulated object, e.g. a piece of wood.

When you hold the gun approx. 5 mm from the piece of wood (fig. 1) the feed
rollers should slip.

If you hold the gun approx. 50 mm from the piece of wood, the wire should be
fed out and bend (fig. 2).

GB

-- 1 2 --

bm29d1ea

6.5 Changing / loading wire Feed 3004

S Open the side panel.
S Disconnect the pressure sensor by folding it backwards, the pressure rollers

slide up.

S Wind any wire that may be left between the rollers back on to the bobbin and

remove the bobbin.

S Straighten out 10--20 cm of the end of the new wire. File off any burrs from the

end of the wire and then feed it into the feed unit.

S Make sure that the end of the wire is correctly positioned in the groove in the

feed rollers and in the outlet nozzle and wire liner.

S Tighten the pressure sensor.
S Close the side panel.

6.6 Changing / loading wire Feed 4804

S Open the side panel.
S Push down the pressure device and pull it towards you and upwards.
S Pull out the bogey
S Wind any wire that may be left between the rollers back on to the bobbin and

remove the bobbin.

S Straighten out 10--20 cm of the end of the new wire. File off any burrs from the

end of the wire and then feed it into the feed unit.

S Make sure that the end of the wire is correctly positioned in the groove in the

feed rollers and in the outlet nozzle and wire liner.

S Replace the bogey.
S Close the side panel.

6.7 Replacing the Feed 3004 feed rollers

S Open the side panel.
S Disconnect the pressure sensor (1) by folding it

backwards.

S Disconnect the pressure rollers (2) by turning the

axle (3) 1/4 turn clockwise and pulling out the axle.
The pressure rollers disconnect.

S Disconnect the feed rollers (4) by unscrewing the

nuts (5) and pulling out the rollers.

Reassemble in the reverse order.

Selecting the correct groove in the feed rollers

Turn the feed roller so that the dimension marking of the
required groove is facing you.

GB

-- 1 3 --

bm29d1ea

6.8 Replacing the Feed 4804 feed rollers

S Open the side panel.
S Push down the pressure device (1) and pull it

towards you and upwards.

S Pull out the bogey (2).
S Remove the socket--head bolts (3) on the

intermediate nozzle and remove it.

S Loosen the bolt holding the outlet nozzle (4)

and push the nozzle back.

S Remove the socket--head bolt (5) in the centre
S Slacken the two socket--head bolts (6) by half a turn.
S Pull out the feed rollers (7).

Reassemble in the reverse order.

Selecting the correct groove in the
feed rollers

Place no, one or two carrier washers
between the outer washer and the feed
rollers. NB: Replace the entire bogey

when changing the pressure rollers (8).

7 MAINTENANCE

Regular maintenance is important in ensuring safe and reliable.

Note!

All guarantee undertakings from the supplier cease to apply if the customer himself
attempts any work in the product during the guarantee period in order to rectify any
faults.

7.1 Inspection and cleaning

Wire feed unit

Check regularly that the wire feed unit is not clogged with dirt.

S Cleaning and replacement of the wire feed unit mechanism’s worn parts should

take place at regular intervals in order to achieve trouble--free wire feed. Note
that if pre--tensioning is set too hard, this can result in abnormal wear on the
pressure roller, feed roller and wire guide.

GB

-- 1 4 --

bm29d1ea

The brake hub

The hub is adjusted when delivered, if
readjustment is required, follow the instructions
below. Adjust the brake hub so that wire is slightly
slack when wire feed stops.

S Adjusting the braking torque:

S Turn the red handle to the locked position.

S Insert a screwdriver into the springs in the hub.

Turn the springs clockwise to reduce the braking torque
Turn the springs counterclockwise to increase the braking torque. NB: Turn

both springs through the same amount.

Welding gun

S Cleaning and replacement of the welding gun’s wear parts should take place at

regular intervals in order to achieve trouble--free wire feed. Blow the wire guide
clean regularly and clean the contact tip.

8 ORDERING OF SPARE PARTS

Repair and electrical work should be performed by an authorized ESAB serviceman.
Use only ESAB original spare and wear parts.

Feed 3004, Feed 4804 is designed and tested in accordance with the international an
European standards IEC/EN 60974--5 and EN 60974--10.
It is the obligation of the service unit which has carried out the service or repair work
to make sure that the product still conforms to the said standard.

Spare parts may be ordered through your nearest ESAB dealer, see the last page of
this publication.

GB

-- 1 5 --

p

Diagram

-- 1 6 --

bm29e11a

Feed 3004, Feed 4804

-- 1 7 --

bm29e11a

-- 1 8 --

page

Feed 3004, Feed 4804

Edition 071005

Ordering number

-- 1 9 --

bm29o11a

1.

Control

panel

Water

cooling

kit

Feeder for

Marathon Pact

Feeder with

open bobbin

Feeder with

capsuled bobbin

Aristot Feed 3004 0458 804 881 0458 805 881 0458 806 881

Aristot Feed 3004 W x 0458 804 891 0458 805 891 0458 806 891

Aristot Feed 3004 MA4 0458 804 884 0458 805 884 0458 806 884

Aristot Feed 3004 W MA4 x 0458 804 894 0458 805 894 0458 806 894

Aristot Feed 3004 MA6 0458 804 886 0458 805 886 0458 806 886

Aristot Feed 3004 W MA6 x 0458 804 896 0458 805 896 0458 806 896

Aristot Feed 3004 U6 0458 804 887 0458 805 887 0458 806 887

Aristot Feed 3004 W U6 x 0458 804 897 0458 805 897 0458 806 897

Aristot Feed 4804 0458 804 981 0458 805 981 0458 806 981

Aristot Feed 4804 W x 0458 804 991 0458 805 991 0458 806 991

Aristot Feed 4804 MA4 0458 804 984 0458 805 984 0458 806 984

Aristot Feed 4804 W MA4 x 0458 804 994 0458 805 994 0458 806 994

Aristot Feed 4804 MA6 0458 804 986 0458 805 986 0458 806 986

Aristot Feed 4804 W MA6 x 0458 804 996 0458 805 996 0458 806 996

Aristot Feed 4804 U6 0458 804 987 0458 805 987 0458 806 987

Aristot Feed 4804 W U6 x 0458 804 997 0458 805 997 0458 806 997

Spare parts list 0458 716 990 0458 716 990 0458 716 990

Instruction manual MA4 x 0458 818 0458 818 0458 818

Instruction manual MA6 x 0458 854 0458 854 0458 854

Instruction manual U6 x 0459 287 0459 287 0459 287

Instruction manuals and the spare parts list are available on the Internet at www.esab.com

Feed 3004

R0458 716/E071005/P28

Wear components

-- 2 0 --

bm29whj1

Item

Ordering no. Denomination Wire type Wire dimensions

HI 1 0455 072 002

0456 615 001

Intermediate nozzle
Intermediate nozzle

Fe, Ss & cored
Al

HI 2 0469 837 880

0469 837 881

Outlet nozzle
Outlet nozzle

Fe, Ss & cored
Al

Ø 2.0 mm steel for 0.6-- 1.6 mm
Ø 2.0 mm plastic for 0.8--1.6 mm

HI 3 0191 496 114 Key

HI 4 0215 701 007 Locking washer

HI 5a 0459 440 001 Motor gear euro

Item Ordering no. Denomination Wire type Wire dimensions Groove

typ

Roller

markings

HI 5b 0459 052 001 Feed/pressure rollers Fe, Ss & cored Ø 0.6 & 0.8 mm V 0.6 S2 &0.8S2

0459 052 002 Feed/pressure rollers Fe, Ss & cored Ø 0.8 & 1,0 mm V 0.8 S2 &1.2S2
0459 052 003 Feed/pressure rollers Fe, Ss & cored Ø 0.9/1.0 & 1.2 mm V 1.0 S2 &1.2S2

0459 052 013 Feed/pressure rollers Fe, Ss & cored Ø 1.4 & 1.6 mm V 1.4 S2 &1.6S2
0458 825 001 Feed/pressure rollers Cored Ø 0.9/1.0 & 1.2 mm V--Knurled 1.0 R2 &1.2R2
0458 825 002 Feed/pressure rollers Cored Ø 1.2 & 1.4 mm V-- Knurled 1.2 R2 &1.4R2

0458 825 003 Feed/pressure rollers Cored Ø1.6mm V--Knurled 1.6 R2 &2.0R2
0458 824 001 Feed/pressure rollers Al Ø 0.8 & 0.9/1.0 mm U 0.8 A2 &1.0A2
0458 824 002 Feed/pressure rollers Al Ø 1.0 & 1.2 mm U 1.0 A2 &1.2A2
0458 824 003 Feed/pressure rollers Al Ø 1.2 & 1.6 mm U 1.2 A2 &1.6A2
0458 874 002 Feed/pressure rollers Al Ø 1.0 & 1.2 mm U 1.0 A2 &1.2A2

Use only pressure and feed rollers marked A2, R2 or S2.

Therollersaremarkedwithwiredimensioninmm,somearealsomarkedwithinch.

Item Ordering no. Denomination Notes

HI 6 Washer Ø 16/5x1

HI 7 Screw M4x12

HI 8 Screw M6x12

HI 9 Washer Ø 16/8.4x1.5

HI 10 0469 838 001 Cover

HI 11 0458 722 880 Axle and Nut

HI 12 0459 441 880 Gear adapter

HI 13 0455 049 001 Inlet nozzle

HI 14 0458 999 001 Shaft

Welding with aluminium wire

In order to weld with aluminium wire, proper rollers, nozzles and liners for aluminium wire MUST be
used, It is recommended to use 3 m long welding gun for aluminium wire, equipped with appropriate
wear parts.

Feed 3004

R0458 716/E071005/P28

-- 2 1 --

bm29whj1

Feed 4804

R0458 716/E071005/P28

-- 2 2 --

bm29whk1

Item

Ordering no. Denomination Wire type Wire dimensions

HK1 0469 837 880

0469 837 881
0469 837 882

Outlet nozzle
Outlet nozzle
Outlet nozzle

Fe, Ss & cored
Al
Fe, Ss & cored

Ø 2.0 mm steel for 0.6-- 1.6 mm
Ø 2.0 mm plastic for 1.0--1.6 mm
Ø 3.4 mm steel for 2.0-- 2.4 mm

Item Ordering no. Denomination Wire type Wire ØmmGroove 1 Groove 2 Groove 3 Groove

typ

Roller /

Bogey

mark-

ings

HK2 0366 966 880 Feed Roller Fe, Ss & cored 0.6--1.2 0.6-- 0.8 0.9--1.0 1.2 V 1

0366 966 881 Feed Roller Fe, Ss & cored 1.4--1.6 1.4--1.6 2.0 2.4 V 2
0366 966 889 Feed Roller Fe, Ss & cored 1.2 .045” / 1.2 .045” / 1.2 .045” / 1.2 V .045 / 7

0366 966 900 Feed Roller Fe, Ss & cored 0.9--1.6 0.9--1.0 1.2 1.4-- 1.6 V 6
0366 966 882 Feed Roller Cored 1.2--2.0 1.2 1.4--1.6 2.0 V-- Knurled 3
0366 966 883 Feed Roller Cored 2.4 2.4 not used not used V--Knurled 4

0366 966 885 Feed Roller Al 1.2 1.2 1.2 1.2 U U2
0366 966 899 Feed Roller Al 1.0--1.6 1.0 1.2 1.6 U U4

Item Ordering no. Denomination Notes

HK3 0156 707 001 Distance washer

HK4 0156 707 002 Adjustment spacer

HK5 Screw M5x20

HK6 Screw M5x16

HD = Heavy Duty

Item

Ordering no. Denomination Wire type Wire dimensions Groove

typ

Roller /

Bogey

markings

HK7 0366 902 880 Bogey (HD) Fe, Ss & cored Ø0.6--1.2mm V 1

0366 902 900 Bogey (HD) Fe, Ss & cored Ø0.9--1.6mm V 6
0366 902 881 Bogey (HD) Fe, Ss & cored Ø1.4--2.4mm V 3
0366 902 894 Bogey (HD) Fe, Ss & cored Ø1.2mm V .045 / 7
0366 902 882 Bogey (HD) Cored Ø1.2--2.0mm V--Knurled 3
0366 902 883 Bogey (HD) Cored Ø2.4mm V--Knurled 4
0366 902 899 Bogey (HD) Al Ø1.0--1.6mm U U4
0366 902 886 Bogey (HD) Al Ø1.2mmx3 U --

Item Ordering no. Denomination Wire type Wire dimensions

HK8 0366 944 001 Washer

HK9 0156 603 001

0156 603 002
0332 322 001
0332 322 002

Intermediate nozzle
Intermediate nozzle
Intermediate nozzle
Intermediate nozzle

Fe, Ss & Al
Fe, Ss & Al
Cored
Cored

Ø 2 mm plastic for 0.6--1.6 mm
Ø 4 mm plastic for 2.0--2.4 mm
Ø 2.4 mm copper for 1.2--2.0 mm
Ø 4 mm copper for 2.4 mm

Item Ordering no. Denomination Note

HK10 0215 702 708 Locking washer

HK11 Nut M10

HK12 0458 748 002 Insulating washer

HK13 0458 748 001 Insulating bushing

Item Ordering no. Denomination Wire type Wire dimensions

HK14 0156 602 001

0156 602 002
0332 318 001
0332 318 002

Inlet nozzle
Inlet nozzle
Inlet nozzle (HD)
Inlet nozzle (HD)

Fe, Ss, Al & Cored
Fe, Ss, Al & Cored
Fe, Ss & Cored
Fe, Ss & Cored

Ø 2 mm plastic for 0.6--1.6 mm
Ø 4 mm plastic for 2.0--2.4 mm
Ø 2.4 mm steel for 1.2-- 2.0 mm
Ø 4 mm steel for 2.4 mm

Feed 4804

R0458 716/E071005/P28

-- 2 3 --

bm29whk1

R0458 716/E071005/P28

Feed 3004, Feed 4804

Accessories

-- 2 4 --

bm29a11a

1 Bobbin cover, plastic 18 kg Ø 300mm ...... 0458 674 880

1 Bobbin cover, metal 18 kg Ø 300mm ....... 0459 431 880

12Bobbin holder ...........................

Adapter for 5 kg bobbin ....................

0458 704 880
0455 410 001

1 Adapter for 440 mm bobbin ................ 0459 233 880

12Lifting eye ...............................

Quick connector MarathonPact ...........

0458 706 880
F102 440 880

1
2
3

Turning piece ............................

Guide pin ................................

Quick connector MarathonPact ...........

0458 703 880
0458 731 880
F102 440 880

R0458 716/E071005/P28

Feed 3004, Feed 4804

-- 2 5 --

bm29a11a

1 Strain relief forweldinggun ................ 0457 341 881

1 Wheel kit forfeed ......................... 0458 707 880

Strain relief bracket for connection set .... 0459 234 880

Counter balance device

(includes mast and counter balance)

for 300 mm bobbin ........................

for 440 mm bobbin ........................

0458 705 880
0458 705 882

R0458 716/E071005/P28

Feed 3004, Feed 4804

-- 2 6 --

bm29a11a

Remote control adapter RA12 12pole .....

For analogue remote controls to CAN based
equipment.

0459 491 910

Remote control adapter RA23 23pole .....

For connecting welding gun with RS3 program
selector to CAN based equipment.

0459 491 911

RemotecontrolunitMTA1CAN ...........

MIG/MAG: wire feed speed and voltage MMA:
current and arc force
TIG: current, pulse and background current

0459 491 880

RemotecontrolunitM110ProgCAN.......

Choice of on of 10 programs
MIG/MAG: voltage deviation
TIG and MMA: current deviation

0459 491 882

RemotecontrolunitAT1CAN .............

MMA and TIG: current

0459 491 883

RemotecontrolunitAT1CFCAN ..........

MMA and TIG: rough and fine setting of
current.

0459 491 884

Remote cable CAN 4 pole -- 12 pole

5m ......................................

10m.....................................

15m.....................................

25m.....................................

0.25m ...................................

0459 554 880
0459 554 881
0459 554 882
0459 554 883
0459 554 884

R0458 716/E071005/P28

Feed 3004, Feed 4804

-- 2 7 --

bm29a11a

Connection set

1.7m ....................................

5m ......................................

10m.....................................

15m.....................................

25m.. .................................

35m.....................................

Connection set water

1.7m ....................................

5m ......................................

10m.....................................

15m.....................................

25m.....................................

35m.....................................

0456 528 880
0456 528 890
0456 528 881
0456 528 882
0456 528 883
0456 528 884

0456 528 885
0456 528 895
0456 528 886
0456 528 887
0456 528 888
0456 528 889

Remote adapter kit used from serial no 451--xxx --xxxx

ForMiggytrac/ Railtrac ....................

For MXH 400w PP ........................

0459 681 880
0459 681 881

Connection kit used from serial no 451-- xxx--xxxx

For MXH 400w PP ........................ 0459 020 883

Welding gun MXH 400w PP

6.0m ....................................

10.0m ...................................

0700 200 015
0700 200 016

Miggytrac 1000, Miggytrac 2000

Equipment for mechanized welding ..........

More infor-­mation at the
nearest
ESAB agency

Railtrac 1000

Equipment for mechanized welding ..........

More infor-­mation at the
nearest
ESAB agency

Information on PSF welding guns can be found in separate brochures.

ESAB AB
SE--695 81 LAXÅ
SWEDEN
Phone [phone]

www.esab.com

070514

ESAB subsidiaries and representative offices

Europe

AUSTRIA

ESAB Ges.m.b.H
Vienna--Liesing
Tel: [phone]
Fax: [phone]

BELGIUM

S.A. ESAB N.V.
Brussels
Tel: [phone]
Fax: [phone]

THE CZECH REPUBLIC

ESAB VAMBERK s.r.o.
Vamberk
Tel: [phone]
Fax: [phone]

DENMARK

Aktieselskabet ESAB
Herlev
Tel:[phone]
Fax:[phone]

FINLAND

ESAB Oy
Helsinki
Tel: [phone]
Fax: [phone]

FRANCE

ESAB France S.A.
Cergy Pontoise
Tel:[phone]
Fax:[phone]

GERMANY

ESAB GmbH
Solingen
Tel: [phone]
Fax: [phone]

GREAT BRITAIN

ESAB Group (UK) Ltd
Waltham Cross
Tel: [phone]
Fax: [phone]

ESAB Automation Ltd
Andover
Tel: [phone]
Fax: [phone]

HUNGARY

ESAB Kft
Budapest
Tel:[phone]
Fax:[phone]

ITALY

ESAB Saldatura S.p.A.
Mesero (Mi)
Tel:[phone]
Fax:[phone]

THE NETHERLANDS

ESAB Nederland B.V.
Amersfoort
Tel: [phone]
Fax: [phone]

NORWAY

AS ESAB
Larvik
Tel:[phone]
Fax:[phone]

POLAND

ESAB Sp.zo.o.
Katowice
Tel: [phone]
Fax: [phone]

PORTUGAL

ESAB Lda
Lisbon
Tel: [phone]
Fax: [phone]

SLOVAKIA

ESAB Slovakia s.r.o.
Bratislava
Tel:[phone]
Fax:[phone]

SPAIN

ESAB Ibérica S.A.
Alcalá de Henares (MADRID)
Tel: [phone]
Fax: [phone]

SWEDEN

ESAB Sverige AB
Gothenburg
Tel:[phone]
Fax:[phone]

ESAB international AB
Gothenburg
Tel:[phone]
Fax:[phone]

SWITZERLAND

ESAB AG
Dietikon
Tel: [phone]
Fax: [phone]

North and South America

ARGENTINA

CONARCO
Buenos Aires
Tel: [phone]
Fax: [phone]

BRAZIL

ESAB S.A.
Contagem--MG
Tel: [phone]
Fax: [phone]

CANADA

ESAB Group Canada Inc.
Missisauga, Ontario
Tel: [phone]
Fax: [phone]

MEXICO

ESAB Mexico S.A.
Monterrey
Tel: [phone]
Fax: [phone]

USA

ESAB Welding & Cutting Products
Florence, SC
Tel: [phone]
Fax: [phone]

Asia/Pacific

CHINA

Shanghai ESAB A/P
Shanghai
Tel: [phone]
Fax: [phone]

INDIA

ESAB India Ltd
Calcutta
Tel: [phone]
Fax: [phone]

INDONESIA

P.T. ESABindo Pratama
Jakarta
Tel: [phone]
Fax: [phone]

JAPAN

ESAB Japan
Tokyo
Tel: [phone]
Fax:[phone]

MALAYSIA

ESAB (Malaysia) Snd Bhd
Selangor
Tel: [phone]
Fax:[phone]

SINGAPORE

ESAB Asia/Pacific Pte Ltd
Singapore
Tel:[phone]
Fax: [phone]

SOUTH KOREA

ESAB SeAH Corporation
Kyungnam
Tel: [phone]
Fax: [phone]

UNITED ARAB EMIRATES

ESAB Middle East FZE
Dubai
Tel: [phone]
Fax: [phone]

Representative offices

BULGARIA

ESAB Representative Office
Sofia
Tel/Fax: [phone]

EGYPT

ESAB Egypt
Dokki--Cairo
Tel: [phone]
Fax: [phone]

ROMANIA

ESAB Representative Office
Bucharest
Tel/Fax: [phone]

RUSSIA

LLC ESAB
Moscow
Tel: [phone]
Fax: [phone]

LLC ESAB
St Petersburg
Tel: [phone]
Fax: [phone]

Distributors

For addresses and phone
numbers to our distributors in
other countries, please visit our
home page

www.esab.com