ESAB Caddy Tig 2200i AC/DC Instruction manual

Caddy®

Tig 2200i AC/DC

Instruction manual

0460 225 301 GB 20220103

Valid for: serial no. 711-, 747-xxx-xxxx

TABLE OF CONTENTS

1

SAFETY

1.1 Meaning of symbols

1.2 Safety precautions

2

INTRODUCTION

2.1 Equipment

2.2 Control panels

3

TECHNICAL DATA

4

INSTALLATION

4.1 Lifting instructions

4.2 Location

4.3 Mains power supply

5

OPERATION

5.1 Connections and control devices

5.2 Key to symbols

5.3 Connection to cooling unit

5.4 Turning on the power source

.......................................................................................................

...............................................................................

.................................................................................

..........................................................................................

...............................................................................................

........................................................................................

......................................................................................

............................................................................................

.................................................................................

...................................................................................................

...............................................................................

................................................................................................

.......................................................................................

.........................................................

....................................................................

................................................................

4

4

4

7

7

7

8

10

10

10

10

12

13

13

14

14

6

MAINTENANCE

6.1 Inspection and cleaning

7

TROUBLESHOOTING

8

ORDERING SPARE PARTS

...........................................................................................

.................................................................................

ASSEMBLY INSTRUCTIONS
DIAGRAM
ORDERING NUMBERS
ACCESSORIES

............................................................................................................

.......................................................................................

...................................................................................................

.........................................................................

........................................................................

..............................................................................

15

15

16

17
18
19
21
22

Rights reserved to alter specifications without notice.

0460 225 301 © ESAB AB 2022

1 SAFETY

1 SAFETY

1.1 Meaning of symbols

As used throughout this manual: Means Attention! Be Alert!

DANGER!
Means immediate hazards which, if not avoided, will result in immediate,

serious personal injury or loss of life.

WARNING!
Means potential hazards which could result in personal injury or loss of life.

CAUTION!
Means hazards which could result in minor personal injury.

WARNING!

Before use, read and understand the instruction manual
and follow all labels, employer´s safety practices and
Safety Data Sheets (SDSs).

1.2 Safety precautions

Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety
precautions must meet the requirements that apply to this type of equipment. The following
recommendations should be observed in addition to the standard regulations that apply to
the workplace.

All work must be carried out by trained personnel well-acquainted with the operation of the
equipment. Incorrect operation of the equipment may lead to hazardous situations which can
result in injury to the operator and damage to the equipment.

1. Anyone who uses the equipment must be familiar with:
○ its operation
○ location of emergency stops
○ its function
○ relevant safety precautions
○ welding and cutting or other applicable operation of the equipment

2. The operator must ensure that:
○ no unauthorised person is stationed within the working area of the equipment

when it is started up

○ no-one is unprotected when the arc is struck or work is started with the

equipment

3. The workplace must:
○ be suitable for the purpose
○ be free from drafts

0460 225 301

- 4 -

© ESAB AB 2022

1 SAFETY

4. Personal safety equipment:
○ Always wear recommended personal safety equipment, such as safety glasses,

flame-proof clothing, safety gloves

○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which

could become trapped or cause burns

5. General precautions:
○ Make sure the return cable is connected securely
○ Work on high voltage equipment may only be carried out by a qualified

electrician

○ Appropriate fire extinguishing equipment must be clearly marked and close at

hand

○ Lubrication and maintenance must not be carried out on the equipment during

operation

WARNING!

Arc welding and cutting can be injurious to yourself and others. Take precautions
when welding and cutting.

ELECTRIC SHOCK - Can kill

• Install and ground the unit in accordance with instruction manual.

• Do not touch live electrical parts or electrodes with bare skin, wet gloves or
wet clothing.

• Insulate yourself from work and ground.

• Ensure your working position is safe

ELECTRIC AND MAGNETIC FIELDS - Can be dangerous to health

• Welders having pacemakers should consult their physician before welding.
EMF may interfere with some pacemakers.

• Exposure to EMF may have other health effects which are unknown.

• Welders should use the following procedures to minimize exposure to
EMF:

○ Route the electrode and work cables together on the same side of

your body. Secure them with tape when possible. Do not place your
body between the torch and work cables. Never coil the torch or work
cable around your body. Keep welding power source and cables as
far away from your body as possible.

○ Connect the work cable to the workpiece as close as possible to the

area being welded.

FUMES AND GASES - Can be dangerous to health

• Keep your head out of the fumes.

• Use ventilation, extraction at the arc, or both, to take fumes and gases
away from your breathing zone and the general area.

ARC RAYS - Can injure eyes and burn skin

• Protect your eyes and body. Use the correct welding screen and filter lens
and wear protective clothing.

• Protect bystanders with suitable screens or curtains.

0460 225 301

NOISE - Excessive noise can damage hearing

Protect your ears. Use earmuffs or other hearing protection.

- 5 -

© ESAB AB 2022

1 SAFETY

MOVING PARTS - Can cause injuries

• Keep all doors, panels and covers closed and securely in place. Have only
qualified people remove covers for maintenance and troubleshooting as
necessary. Reinstall panels or covers and close doors when service is
finished and before starting engine.

• Stop engine before installing or connecting unit.

• Keep hands, hair, loose clothing and tools away from moving parts.

FIRE HAZARD

• Sparks (spatter) can cause fire. Make sure that there are no inflammable
materials nearby.

• Do not use on closed containers.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

CAUTION!

This product is solely intended for arc welding.

WARNING!

Do not use the power source for thawing frozen pipes.

CAUTION!

Class A equipment is not intended for use in residential
locations where the electrical power is provided by the
public low-voltage supply system. There may be
potential difficulties in ensuring electromagnetic
compatibility of class A equipment in those locations,
due to conducted as well as radiated disturbances.

NOTE!
Dispose of electronic equipment at the recycling

facility!

In observance of European Directive 2012/19/EC on
Waste Electrical and Electronic Equipment and its
implementation in accordance with national law,
electrical and/or electronic equipment that has reached
the end of its life must be disposed of at a recycling
facility.

As the person responsible for the equipment, it is your
responsibility to obtain information on approved
collection stations.

For further information contact the nearest ESAB dealer.

ESAB has an assortment of welding accessories and personal protection equipment
for purchase. For ordering information contact your local ESAB dealer or visit us on
our website.

0460 225 301

- 6 -

© ESAB AB 2022

2 INTRODUCTION

2 INTRODUCTION

The Tig 2200i AC/DC is a TIG welding power source, which can also be used for MMA
welding. It can be used with alternating current (AC) or direct current (DC).

ESAB accessories for the product can be found in the "ACCESSORIES" chapter of
this manual.

2.1 Equipment

The power source is supplied with a 5 m return cable, 3 m mains cable, carrying strap, cable
holder, shaft belt, instruction manual for power source and control panel.

2.2 Control panels

• TA33 AC/DC • TA34 AC/DC

See the separate instruction manual for a detailed description of the control panels.

Instruction manuals in other languages can be downloaded from the Internet: www.esab.com

0460 225 301

- 7 -

© ESAB AB 2022

3 TECHNICAL DATA

3 TECHNICAL DATA

Tig 2200i AC/DC, From serial no. 747-xxx-xxxx

Mains voltage 230V, 10%, 1~ 50/60 Hz

Primary current I

max

:

MMA 25 A

TIG 28 A

No-load power (idle state) 41 W

Setting range:

MMA 4A/20V–160A/26.4V

TIG, AC* / DC 3A/10V–220A/18.8V

Values of the conventional load:

TIG (duty cycle at 40°C/104°F ambient temperature):

20% 220 A / 18.8 V

60% 150 A / 16.0 V

100% 140 A / 15.6 V

MMA (duty cycle at 40°C/104°F ambient temperature):

30% 160 A / 26.4 V

60% 120 A / 24.8 V

100% 110 A / 24.4 V

Power factor at maximum current (I2):

MMA 0.99

TIG 0.99

Efficiency at maximum current (I2):

MMA 73 %

TIG 65 %

Apparent power at max current (I2) 6.4 kVA

Active power at max current (I2) 6.3 KW

U0No-load voltage 58 V

UrNo-load voltage with VRD 25 V

Upk(with arc ignition unit, Tig) 10.7 kV

Working temperature -10 to +40°C (+14to+104 °F)

Continual sound pressure at no-load < 70 dB(A)

Dimensions l×w×h 418×188×345 mm (16.46×7.40×13.58in.)

Dimensions l×w×h with cooler 418×188×496 mm (16.46×7.40×19.53in.)

Weight 15.7 kg (34.61lbs)

Weight with cooler 22.1 kg (48.72lbs)

Isolation class transformer H

Enclosure class IP23

0460 225 301

- 8 -

© ESAB AB 2022

3 TECHNICAL DATA

Tig 2200i AC/DC, From serial no. 747-xxx-xxxx

Application class

Restrictive use Class A

*) The minimum current during AC welding depends on the alloy used for the aluminium
plates and their surface cleanliness.

Duty cycle

The duty cycle refers to the time as a percentage of a ten-minute period that you can weld or
cut at a certain load without overloading. The duty cycle is valid for 40°C/104°F, or below.

Enclosure class

The IP code indicates the enclosure class, i.e. the degree of protection against penetration
by solid objects or water.

Equipment marked IP23 is intended for indoor and outdoor use.

Application class

The symbol indicates that the power source is designed for use in areas with increased
electrical hazard.

0460 225 301

- 9 -

© ESAB AB 2022

4 INSTALLATION

4 INSTALLATION

The installation must be carried out by a professional.

CAUTION!

This product is intended for industrial use. In a domestic environment this product may
cause radio interference. It is the user's responsibility to take adequate precautions.

4.1 Lifting instructions

Install the carrying strap as illustrated and lift
the power source by the strap.

4.2 Location

Position the welding power source such that its cooling air inlets and outlets are not
obstructed.

4.3 Mains power supply

NOTE!
Mains supply requirements

This equipment complies with IEC 61000-3-12 provided that the short-circuit power is
greater than or equal to S

the public system. It is the responsibility of the installer or user of the equipment to
ensure, by consultation with the distribution network operator if necessary, that the
equipment is connected only to a supply with a short-circuit power greater than or
equal to S

. Refer to the technical data in the TECHNICAL DATA chapter.

scmin

Check that the welding power source is connected to the
correct mains power supply voltage, and that it is protected by
the correct fuse size.
A protective earth connection must be made in accordance
with regulations.

at the interface point between the user's supply and

scmin

0460 225 301

Rating plate with supply connection data

- 10 -

© ESAB AB 2022

4 INSTALLATION

Recommended fuse sizes and minimum cable areas

Tig 2200i AC/DC

Mains voltage 230V ±10%, 1~50/60Hz

Mains cable area

3×2.5 mm

2

Primary current I

Phase current I

max

1eff

28A

15A

Fuse Anti-surge 16A

Type C MCB 16A

NOTE!

The mains cable areas and fuse sizes as shown above are in accordance with
Swedish regulations. For other regions, supply cables must be suitable for the
application and meet local and national regulations.

0460 225 301

- 11 -

© ESAB AB 2022

5 OPERATION

5 OPERATION

General safety regulations for handling the equipment can be found in the "SAFETY"
chapter of this manual. Read it through before you start using the equipment!





























0460 225 301

- 12 -

© ESAB AB 2022

5 OPERATION

5.1 Connections and control devices

1 Connection for remote control unit 6 Connection for return cable

2 Control panel (see separate instruction

7 Mains switch

manual)

3 Connection for torch 8 Mains cable

4 Connection for gas to the torch 9 Connection for shielding gas

5 Connection for welding cable or torch

5.2 Key to symbols

MMA  TIG  Return clamp























0460 225 301

- 13 -

© ESAB AB 2022

5 OPERATION

5.3 Connection to cooling unit

Only those persons who have appropriate electrical knowledge (authorised personnel) may
remove the safety plates to connect or carry out service, maintenance or repair work on
welding equipment.

See installation instructions in chapter
"INSTALLATION".

NOTE!

Coolant must be topped up if connecting a
welding torch or connection cables that are
4 meters in length or longer.

5.4 Turning on the power source

Turn on the mains power by turning the mains switch to the ”1” position.

Turn the unit off by turning the switch to the ”0” position.

Whether the mains power supply is interrupted or the power unit is switched off in the normal
manner, welding data will be stored so that it is available next time the unit is started.

0460 225 301

- 14 -

© ESAB AB 2022

6 MAINTENANCE

6 MAINTENANCE

NOTE!

Regular maintenance is important for safe and reliable operation.

Only those persons who have appropriate electrical knowledge (authorised personnel) may
remove the safety plates to connect or carry out service, maintenance or repair work on
welding equipment.

CAUTION!

All warranty undertakings from the supplier cease to apply if the customer attempts
any work to rectify any faults in the product during the warranty period.

6.1 Inspection and cleaning

Power source

Check regularly that the welding power source is not clogged with dirt

How often and which cleaning methods apply depend on: the welding process, arc times,
placement, and the surrounding environment. It is normally sufficient to blow down the power
source with dry compressed air (reduced pressure) once a year.

Clogged or blocked air inlets and outlets otherwise result in overheating.

Welding torch

• The wear parts of the welding torch should be cleaned and replaced at regular intervals
in order to achieve trouble-free wire feed. Blow the wire guide clean regularly and clean
the contact tip.

0460 225 301

- 15 -

© ESAB AB 2022

7 TROUBLESHOOTING

7 TROUBLESHOOTING

Try these recommended checks and inspections before sending for an authorised service
technician.

Type of fault Corrective action

No arc. • Check that the mains power supply switch is turned

on.

• Check that the welding current supply and return
cables are correctly connected.

• Check that the correct current value is set.

• Check the mains power supply.

The welding current is
interrupted during welding.

• Check to see whether the thermal cut-outs have
tripped.

• Check the mains power supply fuses.

The thermal cut-out trips
frequently.

• Make sure that you are not exceeding the rated data
for the welding power source (i.e. that the unit is not
being overloaded).

Poor welding performance. • Check that the welding current supply and return

cables are correctly connected.

• Check that the correct current value is set.

• Check that the correct electrodes are being used.

• Check the gas flow.

0460 225 301

- 16 -

© ESAB AB 2022

8 ORDERING SPARE PARTS

8 ORDERING SPARE PARTS

CAUTION!

Repair and electrical work should be performed by an authorised ESAB service
technician. Use only ESAB original spare and wear parts.

Tig 2200i AC/DC is designed and tested in accordance with the international and European
standards IEC/EN 60974-1, 60974-3 and IEC/EN 60974-10 Class A. It is the obligation of
the service unit which has carried out the service or repair work to make sure that the
product still conforms to the mentioned standards.

Spare parts and wear parts can be ordered through your nearest ESAB dealer, see

esab.com. When ordering, please state product type, serial number, designation and spare

part number in accordance with the spare parts list. This facilitates dispatch and ensures
correct delivery.

0460 225 301

- 17 -

© ESAB AB 2022

ASSEMBLY INSTRUCTIONS

ASSEMBLY INSTRUCTIONS

0460 225 301

- 18 -

© ESAB AB 2022

DIAGRAM

DIAGRAM

0460 225 301

- 19 -

© ESAB AB 2022

DIAGRAM

0460 225 301

- 20 -

© ESAB AB 2022

ORDERING NUMBERS

ORDERING NUMBERS

Ordering no. Denomination Type

0460 150 881 Welding power

Caddy® Tig 2200i, AC/DC, TA33 AC/DC

source

0460 150 880 Welding power

Caddy® Tig 2200i, AC/DC, TA34 AC/DC

source

0460 150 882 Welding power

source

0460 150 883 Welding power

source

0460 150 884 Welding power

source

Caddy® Tig 2200i, AC/DC, TA33 AC/DC,
MMA cable kit complete and Tig torch TXH201 4 m

Caddy® Tig 2200i, AC/DC, TA34 AC/DC,
MMA cable kit complete and Tig torch TXH201 4 m

Caddy® Tig 2200i, AC/DC, TA34 AC/DC,
MMA cable kit complete and Tig torch TXH251 4 m,

Water cooler CoolMini, 2-wheel trolley

Filename Denomination Product

0459 839 013 Spare parts list Welding power source, Tig 2200i AC/DC

0460 226 Instruction manual Control panel, Caddy® TA33 AC/DC

0460 227 Instruction manual Control panel, Caddy® TA34 AC/DC

Instruction manuals and the spare parts list are available on the Internet at: www.esab.com

0460 225 301

- 21 -

© ESAB AB 2022

ACCESSORIES

ACCESSORIES

0459 491 910 Remote control adapter RA1212 pole

For analogue remote controls to CAN
based equipment.

0459 491 880 Remote control unit MTA1 CAN

MIG/MAG: wire feed speed and voltage

MMA: current and arc force

TIG: current, pulse and background current

0459 491 882 Remote control unit M1 10Prog CAN

Choice of one of 10 programs

MIG/MAG: voltage deviation

TIG and MMA: current deviation

0459 491 883 Remote control unit AT1 CAN

MMA and TIG: current

0459 491 884 Remote control unit AT1 CF CAN

MMA and TIG: rough and fine setting of
current.

0700 006 884
0700 006 885



Welding cable kit
Return cable kit

Remote cable CAN 4 pole - 12 pole

0459 544 880

0459 554 881

0459 554 882

0459 554 883

0459 554 884

0460 225 301

5 m

10 m

15 m

25 m

0.25 m

- 22 -

© ESAB AB 2022

ACCESSORIES

0460 265 001 Strap

0460 265 002 Cable holder

0460 265 003 Shoulder holder



0459 366 885



0460 330 880

0700 300 552
0700 300 561

Trolley
for 5-10 litre gasbottle

Trolley
for 20-50 litre gasbottle

Tig torch TXH 201 4 m
Tig torch TXH 251w 4 m

0460 315 880 Foot pedal TI Foot CAN

0460 144 880 Cooling unit CoolMini

0460 225 301

- 23 -

© ESAB AB 2022

ESAB AB, Lindholmsallén 9, Box 8004, 402 77 Gothenburg, Sweden, Phone [phone]

http://manuals.esab.com

For contact information visit esab.com