ESAB Caddy Tig 150, Caddy Tig 200 Instruction manual

GB

CaddyTig 150
CaddyTig 200

Instruction manual

0459 264 001 GB 041101

Valid for serial no. 316--xxx--xxxx, 328--xxx--xxxx,
341--xxx--xxxx, 402--xxx--xxxx

1 DIRECTIVE 3........................................................

2SAFETY 3...........................................................

3 INTRODUCTION 4...................................................

3.1 Equipment 5................................................................

4 TECHNICAL DATA 5.................................................

4.1 Settings 6..................................................................

5 INSTALLATION 7....................................................

5.1 Placing 7...................................................................

5.2 Rating plate 7...............................................................

5.3 Mains power supply 7........................................................

5.4 Connections and control devices 8............................................

6 OPERATION 8.......................................................

6.1 Control panel 8.............................................................

6.2 Overheating protection 9.....................................................

6.3 Hidden functions 9..........................................................

7 WELDING 10.........................................................

7.1 TIG welding 10...............................................................

7.2 MMA welding 14.............................................................

8 WELDING DATA MEMORY 15..........................................

9 MAINTENANCE 15....................................................

9.1 Cleaning the dust filter 15.....................................................

10 FAULT TRACING 16...................................................

10.1 Fault codes 16...............................................................

11 ORDERING SPARE PARTS 17..........................................

DIAGRAM 18............................................................

ORDERING NUMBER 22.................................................

SPARE PARTS LIST 23...................................................

ACCESSORIES 24.......................................................

Rights reserved to alter specifications without notice.

TOCe

-- 2 --

GB

1DIRECTIVE

ESAB Welding Equipment AB, S--695 81 Laxå, Sweden, gives its unreserved guarantee that welding
power source CaddyTig 150 / CaddyTig 200 from serial number 316 / 402 complies with standard
IEC/EN 60974--1, in accordance with the requirements of directive (73/23/EEC) and addendum
(93/68/EEC) and with standard EN 50199 in accordance with the requirements of directive
(89/336/EEC) and addendum (93/68/EEC).

DECLARATION OF CONFORMITY

-- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --------

Laxå 2003--04--10

Henry Selenius
Vice President
ESAB Welding Equipment AB
695 81 LAXÅ
SWEDEN Tel: + 46 584 81000 Fax: + 46 584 411924

2SAFETY

Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who
works on or near the equipment observes all the relevant safety precautions. Safety precautions
must meet the requirements that apply to this type of welding equipment. The following recommen­dations should be observed in addition to the standard regulations that apply to the workplace.

All work must be carried out by trained personnel well--acquainted with the operation of the welding
equipment. Incorrect operation of the equipment may lead to hazardous situations which can result
in injury to the operator and damage to the equipment.

1. Anyone who uses the welding equipment must be familiar with:

S its operation
S location of emergency stops
S its function
S relevant safety precautions
S welding

2. The operator must ensure that:
S no unauthorised person is stationed within the working area of the equipment when it is

started up.

S no--one is unprotected when the arc is struck

3. The workplace must:

S be suitable for the purpose
S be free from draughts

4. Personal safety equipment
S Always wear recommended personal safety equipment, such as safety glasses, flame--proof

clothing, safety gloves.

S Do not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become

trapped or cause burns.

5. General precautions

S Make sure the return cable is connected securely.
S Work on high voltage equipment may only be carried out by a qualified electrician.
S Appropriate fire extinquishing equipment must be clearly marked and close at hand.

bt27d2e

-- 3 --

GB

WARNING

ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE PRECAU­TIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE
BASED ON MANUFACTURERS’ HAZARD DATA.

ELECTRIC SHOCK -- Can kill

S Install and earth the welding unit in accordance with applicable standards.
S Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
S Insulate yourself from earth and the workpiece.
S Ensure your working stance is safe.

FUMES AND GASES -- Can be dangerous to health

S Keep your head out of the fumes.
S Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone

and the general area.

ARC RAYS -- Can injure eyes and burn skin.

S Protect your eyes and body. Use the correct welding screen and filter lens and wear protective

clothing.

S Protect bystanders with suitable screens or curtains.

FIRE HAZARD

S Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.

NOISE -- Excessive noise can damage hearing

S Protect your ears. Use earmuffs or other hearing protection.
S Warn bystanders of the risk.

MALFUNCTION -- Call for expert assistance in the event of malfunction.

READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.

PROTECT YOURSELF AND OTHERS!

ESAB can provide you with all necessary welding protection an d accessories.

WARNING!

Read and understand the instruction manual before installing
or operating.

WARNING!

Do not use the power source for thawing frozen pipes.

This product is solely intended for arc welding.

3 INTRODUCTION

The CaddyTig is a welding current power source based on the static converter
technology intended TIG welding and welding with coated electrodes (MMA). The
static converter technology contributes to low energy consumption, low weight and
small dimensions. Advanced electronics with microcomputer control produces e.g.
rapid regulation and top--class welding properties.

bt27d2e

-- 4 --

GB

3.1 Equipment

The CaddyTig is supplied with 3 m of mains cable and an instruction manual.
ESAB’s accessories for the product can be found on page 24.

4 TECHNICAL DATA

CaddyTig 150 CaddyTig 200

Mains voltage 230V, 1∼ 50/60 Hz 230V, 1∼ 50/60 Hz
Fuse (delayed--action) 16 A 16 A
Primary current I
Primary current I
Voltage/current range

(TIG)
(MMA)

Maximum permissible load at TIG

25% duty cycle
35% duty cycle
60% duty cycle

100% duty cycle
Maximum permissible load at MMA

25% duty cycle
35% duty cycle
60% duty cycle

100% duty cycle

Power factor at maximum current 0,62 0,62
Efficiency at maximum current 77 % 79 %
Open--circuit voltage 71 -- 78 V 71 -- 78 V
Operating temperature -- 1 0 ˚C--+40˚C -- 1 0 ˚C--+40˚C
Constant A--weighed sound

pressure
Dimensions, l x b x h 394 x 267 x 274 mm 394 x 267 x 274 mm
Weight 10 kg 10 kg
Enclosure class IP 23C IP 23C
Application class

max
eff

36 A 36 A
21 A 21 A

3 A / 10 V --150 A / 16 V
4 A / 20 V --150 A / 26 V

150 A / 16 V
120 A / 15 V

95 A / 14 V

150 A / 26 V
140 A / 25,5 V
110A/24,5V

90 A / 23,5 V

<70 db <70 db

3 A / 10 V -- 200 A / 18 V
4 A / 20 V -- 150 A / 26 V

200 A / 18 V
180 A / 17 V
140 A / 15,5 V
110A/14,5V

150 A / 26 V
140 A / 25,5V
1 10 A / 24,5V

90 A / 23,5V

Duty cycle

The duty cycle refers to the time as a percentage of a ten--minute period that you can weld at a cer­tain load without overloading.

Enclosure class

The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid
objects or water. Equipment marked IP23 is designed for indoor and outdoor use.

Application class

The symbol indicates that the power source is designed for use in areas with increased
electrical hazard.

bt27d2e

-- 5 --

GB

4.1 Settings

4.1.1 TIG welding without pulsing

Settings Setting range In steps of: Default value

Welding method TIG, TIG pulse or MMA -- TIG
2/4 stroke * 2strokeor4stroke -- 2stroke
HF / LiftArct * HF or Liftarct -- LiftArct
Gas pre--flow 0--5s 0.1 s 0.5 s
Slope up time 0--10s 0.1 s 0.0 s
Slope down time 0--10s 0.1 s 1.0 s
Gas post--flow 0--25s 0.1 s 2.0 s
Current CaddyTig 150 3 --150 A 1A 60 A
Current CaddyTig 200 3 --200 A 1A 60 A

4.1.2 TIG welding with pulsing

Settings Setting range In steps of: Default value

Welding method * TIG, TIG pulse or MMA -- TIG
2/4 stroke * 2strokeor4stroke -- 2stroke
HF / LiftArct * HF or Liftarct -- LiftArct
Gas pre--flow 0--5s 0.1 s 0.5 s
Slope up time 0--10s 0.1 s 0.0 s
Slope down time 0--10s 0.1 s 1.0 s
Gas post--flow 0--25s 0.1 s 2.0 s
Pulse time

Micro pulse**

Background time

Micro pulse**
Pulse current CaddyTig 150 3 -- 150 A 1A 60 A
Background current CaddyTig 150 3 -- 150 A 1A 20 A
Pulse current CaddyTig 200 3 -- 200 A 1A 60 A
Background current CaddyTig 200 3 -- 200 A 1A 20 A

0.1 -- 2.5 s

0.001 -- 0.250 s

0.1 -- 2.5 s

0.001 -- 0.250 s

0.01 s

0.001 s

0.01 s

0.001 s

1.0 s

1.0 s

4.1.3 MMA settin g s

Settings Setting range In steps of: Default value

Welding method TIG / MMA -- TIG
Arc Force 0 -- 99% 1% 5%
Drop welding I/0 -- 0
Regulator type ArcPlust I/0 -- I
Hot start 0 -- 99% 1% 0%
Current CaddyTig 150 4 -- 150 A 2A 100 A
Current CaddyTig 200 4 -- 150 A 2A 100 A

*) These functions cannot be changed while welding is in progress.
**) Gas pre--flow time and micro pulse are hidden functions, see page 9 .

bt27d2e

-- 6 --

GB

5 INSTALLATION

WARNING!

This product is intended for industrial use. In a domestic environment this product may cause radio
interference. It is the user’s responsibility to take adequate precautions.

5.1 Placing

Place the power source so that its cooling air inlets and outlets are not obstructed.

5.2 Rating plate

The rating plate is located on the underside of the power source.

5.3 Mains power supply

Make sure that the welding power source is connected to the correct supply voltage
and that it is protected by the correct fuse rating. The standards for the country in
question must be complied with as regards the mains cable area. A protective earth
connection must be made in accordance with regulations.

5.3.1 Recommended fuse sizes an d minimum cable areas

CaddyTig 150 CaddyTig 200

Mains voltage 230 V ¦10 %, 1--phase 230 V ¦10 %, 1--phase
Mains frequency 50--60 Hz 50--60 Hz
Fuse (delayed--action)

85A 35% duty cycle MMA
120A 20% duty cycle MMA
150A 25% duty cycle MMA

Mains cable, area 3x2.5mm
Welding cable, area MMA 16 mm
Welding cable, area TIG 16 mm

*) NOTE! The mains plug is approved for maximum 16A.
North American version: The mains cable is approved for maximun 18 A.

Note! The cable area and fuse rating above comply with Swedish regulations. Use the welding power

source in accordance with the relevant national regulations.

10 A
16 A

20 A*)

2

2
2

10 A
16 A

20 A*)

3x2.5mm

16 mm
25 mm

2
2

2

bt27d2e

-- 7 --

GB

5.4 Connections and control devices

1 Control panel, 6 Gas hose connection to the TIG torch
2 TIG: Return cable connection (+)

MMA: Welding cable connection (--)

3 Remote control unit connection 8 Gas bottle connection
4 MMA: Return cable connection (--) 9 Mains cable
5 TIG torch connection (--) 10 Mains power supply switch

2 and 4 are used for welding current supply and return cable connection during MMA welding

7 Connection for the TIG torch switch

6OPERATION

General safety regulations for the handling of the equipment can be found on
page 3. Read through before you start using the equipment!

6.1 Control panel

On the upper side of the power source there is a control panel for choosing functions
and setting parameters. This comprises a display, setting knob, LEDs and
pushbuttons. Using the pushbuttons, it is possible to move between the various
functions. The selected function is indicated by the relevant LED lighting up.

The power source checks th e LEDs and all segments in the display when main
switch is turned on. The machine t yp e and program version are also
displayed.

bt27d2e

-- 8 --

GB

A Ampere/Volt B LED (green) mains voltage
C Remote control D LED (yellow) overheating
E Data display F Knob for setting data.

Increase (+) or Decrease (--) selected by

the function pushbuttons

6.1.1 Function symbols in the control panel

TIG Direct current TIG HF 2stroke

MMA Pulse LiftArc 4stroke

Slope up Slope down Gas post--flow

6.2 Overheating protection

The welding power source has a thermal overload trip which operates if the
temperature becomes too high, interrupting the welding current and lighting a
yellow indicating lamp on the front of the power source. The thermal overload trip
resets automatically when the temperature has fallen.

6.3 Hidden functions

The CaddyTig 150 is supplied with ArcPlus, a new type of control that, during MMA
welding, produces a more intensive, more concentrated and calmer arc. It recovers
more quickly after a drop short-- circuit, which reduces the risk of the electrode
becoming caught.

The machine is also equipped with Arc Force, which means that the power source’s
dynamics can be adjusted, softer or harder depending on the type of electrode and
according to preference. However, the Arc Plust regulator’s good properties mean
that there is only reason to alter the Arc Force setting in exceptional cases.

bt27d2e

-- 9 --

GB

The CaddyTig includes additional setting options that are obtained by pressing

and simultaneously for 1 second.

Access to the setting options (A --H) are displayed by pressing or .
Set the values or function by turning the knob.

Hidden functions TIG welding

For TIG, the following options under the double press function can be found under
the letters:

A = setting gas pre--flow time in seconds
b = setting micropulse (TIG pulse Off= 0 or On=1

The following welding data setting options for MMA can be found under the letters:

Hidden functions MMA welding

C = setting ArcForce value in percent
d = setting Drop welding Off=0 or On =1
F = setting regulator ArcPlust Off=1 or On =0
H = setting Hot Start value in percent

Reset additional settings by pressing and simultaneously for
1 second.

7 WELDING

7.1 TIG welding

During TIG welding, the return cable must be connected to (+) and the T IG torch to
(--). If they are connected in reverse, the tungsten electrode will melt.

Pulsing is used for improved control of the weld pool and the solidification process. The
pulse frequency is set so slow that the weld pool has time to solidify at least partially be­tween each pulse. In order to set pulsing, four parameters are required: pulse time,
background time, pulse current and background current.

7.1.1 2stroke

Gas pre--flow Slope

up

Functions when using 2 stroke control of the welding torch.

-- 1 0 --

bt27d2e

Slope down Gas post--

flow

GB

In the 2strokecontrol mode, pressing the trigger switch starts gas pre--flow (if used)
and strikes the arc (1). The current rises to the set value (as controlled by the slope
up function, if in operation). Releasing the trigger switch (2) reduces the current (or
starts slope down if in operation) and extinguishes the arc. Gas post--flow follows if it
is in operation.

7.1.2 4stroke

Gas pre--flow Slope

up

Functions when using 4 stroke control of the welding torch.

Slope down Gas post--

flow

In the 4strokecontrol mode, pressing the trigger switch starts gas pre--flow (if used)
(1). At the end of the gas pre--flow time, the current rises to the pilot level (a few
ampere), and the arc is struck. Releasing the trigger switch (2) increases the current
to the set value (with slope up, if in use). At the end of welding, the welder presses
the trigger switch again (3), which reduces the current to pilot level again (with slope
down, if in use). Releasing the switch again (4) extinguishes the arc and starts gas
post--flow.

7.1.3 HF

The HF function strikes the arc by means of a spark from the electrode to the
workpiece as the electrode is brought closer to the workpiece.

7.1.4 LiftArct

The Lift Arct function strikes the arc when the electrode is brought into contact with
the workpiece and then lifted away from it.

Striking the arc with the Lift Arc function. Step 1: the electrode is touched on to the workpiece. Step 2:
the trigger switch is pressed, and a low current starts to flow. Step 3: the welder lifts the electrode
from the workpiece: the arc strikes, and the current rises automatically to the set value.

bt27d2e

-- 1 1 --

GB

7.1.5 Current

A higher current produces a wider weld pool, with better penetration into the
workpiece.

The current set value can be changed irrespective of which menu is displayed. This
value is displayed in the main menu only.

7.1.6 Pulse

When activating pulse, the power source must be in the position for setting pulse
time/pause time.

1. Gas pre--flow

2. Slope up

3. Pulse current or continuous current

4. Pulse time

5. Background current

6. Background time

7. Slope down

8. Gas post--flow

7.1.7 Pulse and background time

The setting range for these parameters is normally 0.01--2.5 s. However, by using micro
pulse, times down to 0.001 seconds can be set. When the micro pulse function is active,
times shorter than 0.25 seconds are displayed without a decimal point.

Micro pulse is a hidden function, to activate micro pulse, follow the description 6.3 “Hidden
function”.

Pulse time

The time the pulse current is on during a pulse period.

Background time

Time for background current which, along with the time for pulse current, gives the
pulse period.

Background current

The lower of the two current values in the event of pulsed current.

bt27d2e

-- 1 2 --

GB

Pulse current

A higher current produces a wider weld pool, with better penetration into the
workpiece.

The current set value can be changed irrespective of which menu is displayed. This
value is displayed in the main menu only.

Current

Background

time

Pulse current

Background
current

TIG welding with pulsing.

Pulse time

Time

7.1.8 Remote control unit

Using the remote control unit socket on the machine, the current can be controlled r emotely
for both TIG and MMA.
If pulsed current is chosen in TIG mode, it is the pulse current that is remotely controlled.
The value set from the remote control unit is shown on the display by browsing to the
position where the current would have been set without the remote control unit.

This is confirmed by the green LED lighting up.

7.1.9 Gas pre--flow

This controls the time during which shielding gas flows before the arc is struck.

7.1.10 Slope up

The slope up function means that, when the TIG arc strikes, the current rises slowly
to the set value. This provides ‘gentler’ heating of the electrode, and gives the welder
a chance to position the electrode properly before the full current value is reached.

7.1.11 Slope down

TIG welding uses slope down, by which the current falls ’slowly’ over a controlled
time, to avoid craters and/or cracks when a weld is finished.

7.1.12 Gas post--flow

This controls the time during which shielding gas flows after the arc is extinguished.

bt27d2e

-- 1 3 --

GB

7.2 MMA welding

The CaddyTig gives direct current, and you can weld most metals to alloy and non-­alloy steel, stainless steel and cast iron.
The CaddyTig 150 allows you to weld most coated electrodes from ∅ 1.6 to ∅ 3.25.
The CaddyTig 200 allows you to weld most coated electrodes from ∅ 1.6 to ∅ 4.0.

If, when striking the arc, the tip of the electrode is pressed against the metal, it im­mediately melts and sticks to the metal, rendering continued welding impossible.
Therefore, the arc has to be struck in the same way that you would light a m atch.

Quickly strike the electrode against the metal, then raise it so
as to give an appropriate arc length (approx. 2 mm). If the arc
is too long, it will crackle and spit before finally going out com­pletely.

If you are working on a welding bench, check before attempting
to strike the arc that residual waste metal, pieces of electrode

cmha2p11

or other objects on the bench do not insulate the part to be
welded.

Once the arc has been struck, move the electrode from left to
right. The electrode must be at an angle of 60˚ to the metal in
relation to the direction of welding.

When you want to weld wide beads, or when you want the weld
to be so thick that you have to weld in a number of layers, how­ever, you have to use lateral movements.

cmha2p10

7.2.1 Setting regulator -- ArcPlust

The CaddyTig is supplied with ArcPlust, a new type of control that, during MMA
welding, produces a more intensive, more concentrated and calmer arc. It recovers
more quickly after a drop short-- circuit, which reduces the risk of the electrode
becoming stuck.

7.2.2 Arc Fo rce

The Arc Force setting alters the machine’s dynamics. A softer/harder arc can be obtained.
The arc force is important in determining how the current changes in response to a change
in the arc length. A lower value gives a calmer arc with less spatter.

7.2.3 Drop welding

Drop welding can be used when welding with stainless electrodes.
This technique involves alternately striking and extinguishing the arc in order to achieve
better control of the supply of heat. The electrode needs only to be raised slightly to
extinguish the arc.

7.2.4 Hot Start

Hot start increases the weld current for an adjustable time at the start of welding,
thus reducing the risk of poor fusion at the beginning of the joint.

bt27d2e

-- 1 4 --

GB

8 WELDING DATA MEMORY

The CaddyTig can store 4 different welding data setups in the machine’s memory,
divided between 2 in TIG mode and 2 in MMA mode.

The following can be stored:

In TIG mode all settings can be stored.
In MMA mode only welding current can be stored.

For setting gas pre--flow, TIG MicroPulse, ArcForce and drop welding:

Press button or for 5 seconds to store the data in the memory. At the be­ginning the green LED shines constantly, and then starts flashing when the data has
been saved.

To switch between the predefined settings, use button or

Change settings with the torch trigger by pressing .
Press the torch trigger quickly ( within 0,3 seconds) to switch between the stored settings.

The CaddyTig has a back--up battery so that the settings remain even if the machine
has been switched off or disconnected from the mains.

9 MAINTENANCE

Regular maintenance is important for safe, reliable operation.

Note!

All guarantee undertakings from the supplier cease to apply if the customer himself
attempts any work in the product during the guarantee period in order to rectify any
faults.

The CaddyTig requires little maintenance. In normal cases, it is sufficient to blow it
clean using dry compressed air once a year, but this should be done more often if it
is set up in a dusty, dirty area.

9.1 Cleaning the dust filter

S Remove th e fan grille: see sketch.
S Release the dust filter
S Blow the filter clean with compressed air (reduced pressure).
S Replace the fan grille with the dust filter.

bt27d2e

-- 1 5 --

GB

10 FAULT TRACING

Tr y these recommended checks and inspections before sending for an authorised
service technician.

Type of fault Action

No arc. S Check that the mains power supply switch is turned on.

S Check that the welding current supply and return cables are

correctly connected.

S Check that the correct current value is set.

The welding current is interrup­ted during welding.

S Check whether the thermal overload trips have operated

(indicated by the yellow lamp on the front panel).

S Check the main power supply fuses.

The thermal overload trip opera­tes frequently.

Poor welding performance. S Check that the welding current supply and return cables are

S Make sure that you are not exceeding the rated data for the

welding power source (i.e. that the unit is not being
overloaded).

S Check that the dust filter is clean.

correctly connected.

S Check that the correct current value is set.
S Check that the correct electrodes are being used.
S Check the main power supply fuses.

10.1 Fault codes

The CaddyTig comes with built--in fault monitoring. If a fault occurs, a code is shown
in the display.

If any of these fault codes is displayed permanently or recurs often, the machine
should be sent to an authorised ESAB service workshop for repair.

Fault Description Resetting Action

E1 Internal RAM fault Restart the machine.

If the fault persists, contact a
service workshop

E2 External RAM fault Restart the machine.

If the fault persists, contact a
service workshop

E3 EPROM fault Restart the machine.

If the fault persists, contact a
service workshop

E4 Fault in RAM with battery

backup

E5 Memory error, variable va-

lue outside limits

E6 Low battery voltage Reset by pressing a button If the fault persists, contact a

E10 + 20V fault

(18.5 – 21.5 V)

E11 --15V fault

(--13.0 -- --16.0)

E13 High temperature Automatic reset once fault

Automatic reset once fault
has disappeared

Automatic reset once fault
has disappeared

has disappeared

Restart the machine.
If the fault persists, contact a
service workshop

Restart the machine.
If the fault persists, contact a
service workshop

service workshop

bt27d2e

-- 1 6 --

GB

Fault ActionResettingDescription

E14 Current servo fault Automatic reset once fault

has disappeared Also reset
by pressing a button

E99 Bridging fault The digital control card is

bridged in a non--defined
combination.

Restart the machine.
If the fault persists, contact a
service workshop

11 ORDERING SPARE P ARTS

CaddyTig 150 / CaddyTig 200 is designed and tested in accordance with the internatio­nal and European standards IEC/EN 60974--1 and EN 50199. It is the obligation of the
service unit which has carried out the service or repair work to make sure that the pro­duct still conforms to the said standard.

Repair and electrical work should be performed by an authorized ESAB serviceman.
Use only ESAB original spare and wear parts.

Spare parts may be ordered through your nearest ESAB dealer, see the last page of
this publication.

bt27d2e

-- 1 7 --

Diagram

CaddyTig 150

CaddyTig 150

-- 1 8 --

CaddyTig 150

-- 1 9 --

CaddyTig 200

CaddyTig 200

-- 2 0 --

CaddyTig 200

-- 2 1 --

CaddyTig 150, Cadd yTig 200

Ordering number

Ordering no. Denomination Type Notes

0459 199 881 Welding Power source CaddyTig 150 for 230 V

mains voltage

0459 199 885 Welding Power source CaddyTig 150 for 230 V

mains voltage

0459 199 887 Welding Power source CaddyTig 150 for 230 V

mains voltage

0459 199 888 Welding Power source CaddyTig 150 for 230 V

mains voltage

0459 199 883 Welding Power source CaddyTig 200 for 230 V

mains voltage

0459 199 889 Welding Power source CaddyTig 200 for 230 V

mains voltage

0459 264 990 Spare part list CaddyTig 150/CaddyTig 200 English only

Incl welding kit

CSA version for the North
American market.
Incl welding kit

CSA version for the North
American market

Incl welding kit

bt27o

-- 2 2 -­Edition 041101

CaddyTig 150, Cadd yTig 200

Spare parts list

Qty Ordering no. Denomination

Item

101 1 0459 277 001 Filter

bh26s

-- 2 3 --

Edition 041101

CaddyTig 150, Cadd yTig 200

Accessories

MMA welding and return cable kit ........

(”crocodile” type holder)

MMA welding and return cable kit ........

(”screwe” type holder)

Remote control MMA 1 (10mcable).......

MMA and TIG: current

Foot control FS002 ......................

MMA and TIG: current

Remote control unit AT1 .................

MMA and TIG: current

Remote control unit AT1 CF .............

MMA and TIG: rough and fine setting of
current.

0349 501 078

0349 501 079

0349 501 024

0349 090 886

0459 491 896

0459 491 897

Remote cable 12 pole -- 8 pole

5m .....................................

10m....................................

15m....................................

25m....................................

Shoulderstrap .......................... 0459 367 880

0459 552 880
0459 552 881
0459 552 882
0459 552 883

bt27a

-- 2 4 --

Edition 041101

CaddyTig 150, Cadd yTig 200

Trolley small gas bottle .................. 0459 366 880

TIG Torch ...............................

BTF 150 OKC25

0458 218 890

bt27a

-- 2 5 --

Edition 041101

ESAB subsidiaries and representative offices

Europe

AUSTRIA

ESAB Ges.m.b.H
Vienna--Liesing
Tel: [phone]
Fax: [phone]

BELGIUM

S.A. ESAB N.V.
Brussels
Tel: [phone]
Fax: [phone]

THE CZECH REPUBLIC

ESAB VAMBERK s.r.o.
Prague
Tel: [phone]
Fax: [phone]

DENMARK

Aktieselskabet ESAB
Copenhagen--Valby
Tel:[phone]
Fax:[phone]

FINLAND

ESAB Oy
Helsinki
Tel: [phone]
Fax: [phone]

FRANCE

ESAB France S.A.
Cergy Pontoise
Tel:[phone]
Fax:[phone]

GERMANY

ESAB GmbH
Solingen
Tel: [phone]
Fax: [phone]

GREAT BRITAIN

ESAB Group (UK) Ltd
Waltham Cross
Tel: [phone]
Fax: [phone]

ESAB Automation Ltd
Andover
Tel: [phone]
Fax: [phone]

HUNGARY

ESAB Kft
Budapest
Tel:[phone]
Fax:[phone]

ITALY

ESAB Saldatura S.p.A.
Mesero (Mi)
Tel:[phone]
Fax:[phone]

THE NETHERLANDS

ESAB Nederland B.V.
Utrecht
Tel: [phone]
Fax: [phone]

NORWA Y

AS ESAB
Larvik
Tel:[phone]
Fax:[phone]

POLAND

ESAB Sp.z.o.o
Warszaw
Tel: [phone]
Fax: [phone]

PORTUGAL

ESAB Lda
Lisbon
Tel: [phone]
Fax: [phone]

SLOVAKIA

ESAB Slovakia s.r.o.
Bratislava
Tel:[phone]
Fax:[phone]

SPAIN

ESAB Ibérica S.A.
Alcobendas (Madrid)
Tel: [phone]
Fax: [phone]

SWEDEN

ESAB Sverige AB
Gothenburg
Tel:[phone]
Fax:[phone]

ESAB International AB
Gothenburg
Tel:[phone]
Fax:[phone]

SWITZERLAND

ESAB AG
Dietikon
Tel: [phone]
Fax: [phone]

North and South America

ARGENTINA

CONARCO
Buenos Aires
Tel: [phone]
Fax: [phone]

BRAZIL

ESAB S.A.
Contagem--MG
Tel: [phone]
Fax: [phone]

CANADA

ESAB Group Canada Inc.
Missisauga, Ontario
Tel: [phone]
Fax: [phone]

MEXICO

ESAB Mexico S.A.
Monterrey
Tel: [phone]
Fax: [phone]

USA

ESAB Welding & Cutting Products
Florence, SC
Tel: [phone]
Fax: [phone]

Asia/Pacific

CHINA

Shanghai ESAB A/P
Shanghai
Tel: [phone]
Fax: [phone]

INDIA

ESAB India Ltd
Calcutta
Tel: [phone]
Fax: [phone]

INDONESIA

P.T. Esabindo Pratama
Jakarta
Tel: [phone]
Fax: [phone]

MALAYSIA

ESAB (Malaysia) Snd Bhd
Selangor
Tel: [phone]
Fax: [phone]

SINGAPORE

ESAB Singapore Pte Ltd
Singapore
Tel: [phone]
Fax: [phone]

ESAB Asia/Pacific Pte Ltd
Singapore
Tel: [phone]
Fax: [phone]

SOUTH KOREA

ESAB SeAH Corporation
Kyung--Nam
Tel: [phone]
Fax: [phone]

UNITED ARAB EMIRATES

ESAB Middle East
Dubai
Tel: [phone]
Fax: [phone]

Representative offices

BULGARIA

ESAB Representative Office
Sofia
Tel/Fax: [phone]

EGYPT

ESAB Egypt
Dokki--Cairo
Tel: [phone]
Fax: [phone]

ROMANIA

ESAB Representative Office
Bucharest
Tel/Fax: [phone]

RUSSIA--CIS

ESAB Representative Office
Moscow
Tel:[phone]
Fax: [phone]

ESAB Representative Office
St Petersburg
Tel:[phone]
Fax: [phone]

Distributors

For addresses and phone
numbers to our distributors in
other countries, please visit our
home page

www.esab.com

ESAB AB
SE--695 81 LAXÅ
SWEDEN
Phone [phone]

www.esab.com

031021