Page 1
Hardware Parts List for Manual HT Series
A. Mounting Bracket
x2pcs
B. M10 Anchor and
M4x50 Screw x4pcs
C. Suspended Ceiling
Bracket Connector x2pcs
D. M5x15 Screw& Bolt
x4pcs
Manual HT Series
Premium Qual ity Manual Pull-Down Projector Screen
User’s Guide
Thank you for choosing the Manual HT projection screen! Please read through this user guide
before utilizing the screen. Correct usage and maintenance will ensure a long product life.
Care & Use Instructions
◆ Dust, dirt and scratches on the projection surface will affect the picture quality, please take note
of the points below to prevent that from occurring:
1. Do not touch the projection surface with your hands
2. Do not write or draw on the projection surface
3. Do not use fingers or sharp objects to point on the projection surface; this will damage
the screen material.
4. Use a soft-damp cloth to clean the projection surface; do not use chemical cleaning
agents or alcohol.
5. Use clean water when dampening the cleaning cloth and do not rub against the material
to clean it.
◆To avoid damage and injury, the screen should only be operated by adults.
Pre-installation
1. Carefully unpack the screen.
2. Always handle the screen in a leveled position on a clean surface.
Rev.062017-BR
www.elitescreens.com
1
Page 2
Installation In str uc t ion s
Mounting bracket
Fix Plate 1
M4x50 Screw
Mounting Bracket
Wall
Please consult a professional installer, Elite Screens is not liable for faulty installations.
Flush Mount to the Wall
1. Mark the location of where the screen is to be installed, drill your holes and insert the
M10Anchors (B).
2. Install the Mounting Brackets (A) to the wall and secure with the M4x50 Screws (B).
Mounting Bracket
Anchor
3. Attach the screen to the Mounting Brackets (A) by inserting the top of the case to Fix Plate 1 and
securing the back of the case to Fix Plate 2. Make sure the case slots are securely attached to the
mounting brackets.
Fix Plate 2
Fix Plate 1 Fix Plate 2
Mounting Bracket Mounting Bracket
Mounting Bracket Case Slot 1
Case Slot 2 Screen Case
Rev.062017-BR
www.elitescreens.com
2
Page 3
Fix Plate1
Fix Plate 2
Flush Mount to the Ceiling
1. Mark the location of where the screen is to be installed, drill your holes and insert the
M10Anchors (B).
2. Install the Mounting Brackets (A) to the ceiling and secure with the M4x 50 Screws ( B).
Ceiling M10 Anchor
Mounting B racket
Mounting Bracket Fix Plate 1
M4x50 Screw
Mounting B racketFix Plate 2
3. Attach the screen to the Mounting Bracket (A) by inserting the top of the case to FixPlate 1 and
securing the back of the case to Fix Plate 2. Make sure the case slots are securely attached to the
Mounting Bracket (A).
Suspended Ceiling using Chains (additional hardware required)
1. You can also hang the screen on a ceiling by using chains (not included).
2. Connect the Suspended Ceiling Bracket Connector (C) to the Mounting Bracket (A) and
secure with the M5x15 Screws & Bolts (D).
(D) (C)
M5x15 Bolt
Mounting Bracket
(A) M5 M5x15 Sc rew (D)
Rev.062017-BR
Suspended Ceiling Bra cket Connecto r
www.elitescreens.com
3
Page 4
3. Insert chains (not included) through the loop holes of the Suspended Ceiling Bracket
Connector(C).
Suspended Ceiling Bracket Connector
Loop Holes
(C
Screen removal from the Mounting Brackets
1. Pull down on the Mounting Bracket Release Tab and remove the bottom case away from the
wall/ceiling followed by the top of the case.
Release Tab
Pull bottom of case first away from wall/ceiling
Screen Operation
1. Pull the screen down from the lanyard or from the handle
only in a 90-degree angle. To achieve this, make sure to pull
straight down and allowing the screen to come up to lock into
place. Do not attempt to pull the screen down by the surface
or touch the screen, as it will damage the screen and void
the warranty.
2. To retract the screen, simply pull the screen down more than
2 inches and retract the screen back releasing it up gently. The
screen is equipped with a SLOW RETRACT MECHANISM
which allows the screen to slowly retract without the need to
hold on to the handle or lanyard. Simply release the handle and
the screen will retract by itself into the housing.
Rev.062017-BR
www.elitescreens.com
4
Page 5
Attention: If the screen does not unlock,
carefully pull the screen straight down with a
little force. Always pull the screen down at a
90-degree angle.
For more information, technical support or your local EliteScreens
contact, please visit
www.elitescreens.com
Rev.062017-BR
www.elitescreens.com
5
Loading...