Erreka Mole Swing Gate Opener User Manual
IMPORTANT REMARKS
ERREKA has the right to modify the product without
previous notice; it also declines any responsibility to
damage or injury to people or things caused by improper
use or wrong installation.
C DECLARATION OF INCORPORATION FOR
E
PARTLY COMPLETED MACHINERY
(Directive 2006/42/EC, Annex II-B)
The manufacturer Matz-Erreka, S.Coop., headquarters in
Bº Ibarreta s/n, 20577 Antzuola (Gipuzkoa), España
m Please read this instruction manual very carefully
before installing and programming your control unit.
• This instruction manual is only for qualified technicians, who
specialize in installations and automations.
• The contents of this instruction manual do not concern the
end user.
• Every programming and/or every maintenance service should
be done only by qualified technicians.
AUTOMATION MUST BE IMPLEMENTED IN COMPLIANCE
WITH THE EUROPEAN REGULATIONS IN FORCE:
EN 60204-1 (Machinery safety electrical equipment of
machines, part 1: general rules)
EN 12445 (Safe use of automated locking devices, test
methods)
EN 12453 (Safe use of automated locking devices,
requirements)
• The installer must provide for a device (es. magnetotermical
switch) ensuring the omnipolar sectioning of the equipment
from the power supply.
The standards require a separation of the contacts of at
least 3 mm in each pole (EN 60335-1).
• The plastic case has an IP55 insulation; to connect flexible
or rigid pipes, use pipefittings having the same insulation
level.
• Installation requires mechanical and electrical skills,
therefore it shall be carried out by qualified personnel only,
who can issue the Compliance Certificate concerning the
whole installation (Machine Directive 98/37/EEC, Annex IIA).
Under its sole responsibility hereby declares that:
the partly completed machinery model(s):
MO230 (230V), MO120 (120V)
Identification number and year of manufacturing:
typed on nameplate
Description: electromechanical actuator for gates
is intended to be installed on gates, to create a machine
according to the provisions of the Directive 2006/42/EC.
The machinery must not be put into service until the final
machinery into which it has to be incorporated has been
declared in conformity with the provisions of the Directive
2006/42/EC (annex II-A).
- is compliant with the applicable essential safety requirements
of the following Directives:
Machinery Directive 2006/42/EC (annex I, chapter 1)
Low Voltage Directive 2006/95/EC.
Electromagnetic Compatibility Directive 2004/108/EC.
The relevant technical documentation is available at the national
authorities’ request after justifiable request to:
Matz-Erreka,S.Coop.
Bº Ibarreta s/n, 20577 Antzuola (Gipuzkoa), España
The person empowered to draw up the declaration and to
provide the technical documentation:
Roberto Corera
Business Manager
Antzuola, 17/10/2011
ENGLISH
• The automated vehicular gates shall comply with the
following rules: EN 12453, EN 12445, EN 12978 as well as
any local rule in force.
• Also the automation upstream electric system shall comply
with the laws and rules in force and be carried out
workmanlike.
• The door thrust force adjustment shall be measured by
means of a proper tool and adjusted according to the max.
limits, which EN 12453 allows.
• We recommend to make use of an emergency button, to be
installed by the automation (connected to the control unit
STOP input) so that the gate may be immediately stopped
in case of danger.
• The appliance is not to be used by children or persons with
reduced physical, sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given
supervision or instruction.
• Children being supervised do not play with the appliance.
13
TECHNICAL DATA
MO120 (120V) MO230 (230V)
2 x 800 Kg
Max. leaf lenght* m
Power supply V / Hz 120 / 60 230 / 50
Idling current A 3 1,5
Maximum current absorption A 4,8 2,4
aximum power
M
Nominal power W 350 350
Capacitor µF 35 14
Opening time (90°) s 15 17
Maximum torque N m 320 320
ENGLISH
Working temperature °C -20 ÷ +55 -20 ÷ +55
Thermal protection °C 150 150
Working cycle % 30 30
Motor weight Kg 11 11
Protection IP 67 67
W 5
* WARNING: if it is installed the accessory device for
opening up to 180° (code AMO02), the maximum length of
the wing is 2,5m for a maximum weight of 400Kg
2,5 x 550 Kg
3 x 400 Kg
3,5 x 350 Kg
00
2 x 800 Kg
2,5 x 550 Kg
3 x 400 Kg
3,5 x 350 Kg
00
5
Max. leaf weight
Max. leaf lenght
PREPARATORY STEPS
The new series of actuadors MOLE, has been devised to serve gates up to 800 Kg with
leaf up to 3 meters wide (look at the table technical data). Before proceeding with the
installation, please make sure that your gate opens and closes freely, and that:
• Hinges and pins are in optimum condition and properly greased.
• No obstacles are within the moving area.
• There is no friction with the ground or between the leaves.
• Your gate shall be equipped with central
fundamental for the good system operation.
and side stops, which are
14
Loading...