Erreka Calypso Swing Gate Opener User Manual

IMPORTANT REMARKS

ERREKA has the right to modify the product without previous notice; it also declines any responsibility to damage or injury to people or things caused by improper use or wrong installation.

C DECLARATION OF INCORPORATION FOR

E PARTLY COMPLETED MACHINERY

(Directive 2006/42/EC, Annex II-B)

The manufacturer (*) Matz-Erreka,S.Coop., headquarters in Bº Ibarreta s/n, 20577 Antzuola (Gipuzkoa), España

m Please read this instruction manual very carefully

before installing and programming your control unit.

• This instruction manual is only for qualified technicians, who specialize in installations and automations.

• The contents of this instruction manual do not concern the end user.

• Every programming and/or every maintenance service should be done only by qualified technicians.

AUTOMATION MUST BE IMPLEMENTED IN COMPLIANCE WITH THE EUROPEAN REGULATIONS IN FORCE:

EN 60204-1 (Machinery safety electrical equipment of

machines, part 1: general rules)

EN 12445 (Safe use of automated locking devices, test

methods)

EN 12453 (Safe use of automated locking devices,

requirements)

• The installer must provide for a device (es. magnetotermical switch) ensuring the omnipolar sectioning of the equipment from the power supply. The standards require a separation of the contacts of at least 3 mm in each pole (EN 60335-1).

• The plastic case has an IP55 insulation; to connect flexible or rigid pipes, use pipefittings having the same insulation level.

• Installation requires mechanical and electrical skills, therefore it shall be carried out by qualified personnel only, who can issue the Compliance Certificate concerning the whole installation (Machine Directive 2006/42/CEE, Annex IIA).

Under its sole responsibility hereby declares that:

the partly completed machinery model(s): CA43 (*), CA53 (*), CA43M (*), CA53M (*)

dentification number and year of manufacturing: typed on

nameplate

Description: electromechanical operator for gates

- is intended to be installed on gates, to create a machine

according to the provisions of the Directive 2006/42/EC. The machinery must not be put into service until the final machinery into which it has to be incorporated has been declared in conformity with the provisions of the Directive 2006/42/EC (annex II-A).

- is compliant with the applicable essential safety requirements of the following Directives: Machinery Directive 2006/42/EC (annex I, chapter 1) Low Voltage Directive 2006/95/EC. Electromagnetic Compatibility Directive 2004/108/EC.

The relevant technical documentation is available at the national authorities’ request after justifiable request to:

Matz-Erreka,S.Coop. Bº Ibarreta s/n, 20577 Antzuola (Gipuzkoa), España

The person empowered to draw up the declaration and to provide the technical documentation:

Roberto Corera

Business Manager Antzuola, 17/10/2011

ENGLISH

• The automated vehicular gates shall comply with the following rules: EN 13241-1, EN 12453, EN 12445 as well as any local rule in force.

• Also the automation upstream electric system shall comply with the laws and rules in force and be carried out workmanlike.

• The door thrust force adjustment shall be measured by means of a proper tool and adjusted according to the max. limits, which EN 12453 allows.

• We recommend to make use of an emergency button, to be installed by the automation (connected to the control unit STOP input) so that the gate may be immediately stopped in case of danger.

• The appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.

• Children being supervised do not play with the appliance.

(*) made in extra EU Countries on behalf of Matz-Erreka,S.Coop.

ECHNICAL DATA

CA43 CA53 CA43M CA53M

Max. leaf lenght m 2,5 3 2,5 3

Max. leaf weight Kg 400 500 400 500

Power supply VAC - Hz 230 - 50 230 - 50 120 - 60 120 - 60

Idling current A 0,8 0,8 2 2

ull load current

Maximum Power W 200 200 300 300

Capacitor µF 8 8 25 25

Max travel mm 400 500 400 500

A 1 1 2

ENGLISH

Operating speed m/s 0,016 0,016 0,018 0,018

Maximum thrust N 2300 2300 2300 2300

Working temperature °C -30 ÷ +50 -30 ÷ +50 -30 ÷ +50 -30 ÷ +50

Protection IP 44 44 44 44

Working cycle % 30 30 30 30

Motor weight Kg 6,5 6,8 6,5 6,8

CALYPSO 400

CA43, CA43M

A 819 944

B 762 887

C 1162 1387

CALYPSO 500

CA53, CA53M

NSTALLATION LAYOUT

ENGLISH

 CALYPSO operator

 Blinker

 Aerial

 Key or digital selector

cable 4 x 1 mm

cable 2 x 1,5 mm

cable RG-58

cable 2 x 1 mm

 Internal photocells

 External photocells

 Safety edge (EN 12978)

 Control unit

cable 4 x 1 mm2(RX) cable 2 x 1 mm2(TX)

cable 3 x 1,5 mm

PREPARATORY STEPS

The new series of operators CALYPSO, has been devised to serve gates up to 500 Kg with leaf up to 3 meters wide (look at the table technical data). Before proceeding with the installation, please make sure that your gate opens and closes freely, and that:

• Hinges and pins are in optimum condition and properly greased.

• No obstacles are within the moving area.

• There is no friction with the ground or between the leaves.

• Your gate shall be equipped with central

 and side  stops, which are fundamental for the good system operation.

+ 5 hidden pages