ERNITEC Orion/3-DN Outdoor Installation & User's Instructions

00P3H8110ZXSEC6

Orion/3-DN High Speed Dome Camera

Outdoor Dome

Installation & User Instructions

Orion/3-DN Outdoor

1

Preface

The information given in this manual was current when published. The company reserves the right to revise and improve its products. All specifications are subject to change without notice.

Notice

To work with the Integrated High Speed Dome Cameras, any installer or technician must have the following minimum qualifications:

 A basic knowledge of CCTV systems and components  A basic knowledge of electrical wiring and low-voltage electrical

hookups

 A basic knowledge of network system setting  Have read this manual completely

Copyright

Under copyright laws, the contents of this user manual may not be copied, photocopied, translated, reproduced or reduced to any electronic medium or machine-readable format, in whole or in part, without prior written permission of the company.

Important Information

Before proceeding, please read and observe all instructions and warnings in this manual. Retain this manual with the original bill of sale for future reference and, if necessary, warranty service. When unpacking your unit, check for missing or damaged items. If any item is missing, or if damage is evident, DO NOT INSTALL OR OPERATE THIS PRODUCT. Contact your dealer for assistance.

Regulation

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Orion/3-DN Outdoor

2

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste in accordance with Directive 2002/96/EC. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By proper waste handling of this product you ensure that it has no negative consequences for the environment and human health, which could otherwise be caused if this product is thrown into the garbage bin. The recycling of materials will help to conserve natural resources.

For more details information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

Compliance is evidenced by written declaration from our suppliers, assuring that any potential trace contamination levels of restricted substances are below the maximum level set by EU Directive 2002/95/EC, or are exempted due to their application.

Orion/3-DN Outdoor

3

Cautions

 Handle the camera carefully

Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by improper handing or storage.

 Installing electricity wiring carefully

Ask qualified personnel of electrical wiring for the installation. Please note that input electricity to the unit is at tolerance of DC 12V/AC 24V ± 10%.

The camera is capable of surge protection; ensure AC power model unit grounded appropriately against damage of heavy current or electric shock.

Refer to the camera’s installation guide for more information.

 Do not disassemble the camera

To prevent electric shock, do not remove screws or covers. There are no user serviceable parts inside. Ask a qualified service person for servicing.

 Do not block cooling holes on the bracket

This camera has a cooling fan inside. Blocking the cooling holes leads to build up of heat the camera and may cause malfunction.

 Do not operate the camera beyond the specified temperature,

humidity or power source ratings

Use the camera under conditions where temperature is between-50°C ~ 50°C (-58°F ~ 122°F), and humidity is below 90%.

 Do not expose the camera to rain or moisture, or try to operated it in

wet areas

This product is designed for indoor use or locations where it is protected from rain and moisture. Turn the power off immediately if the camera is wet and ask a qualified service person for servicing. Moisture can damage the camera and also create the danger of electric shock.

Orion/3-DN Outdoor

4

 Do not use strong or abrasive detergents when cleaning the camera

body

Use a dry cloth to clean the camera when dirty. In case the dirt is hard to remove, use a mild detergent and wipe gently.

 Never face the camera towards the sun

Do not aim the camera at bright objects. Whether the camera is in use or not, never aim it at the sun or other extremely bright objects. Otherwise, the camera may be smeared or damaged.

Orion/3-DN Outdoor

5

Table of Contents

1. Overview ................................................................................................................................ 7

1.1 Product Features ......................................................................................................... 8

1.2 Product Application ...................................................................................................... 9

2. Connecting the Dome Camera ........................................................................................... 10

2.1 Package Contents ..................................................................................................... 10

2.2 Switch/Connector Definition ....................................................................................... 11

2.3 Communication Switch Setting .................................................................................. 12

2.4 ID Setting ................................................................................................................... 13

2.5 Camera Control Protocol Setting ............................................................................... 14

2.6 22-Pin Connector Definition ....................................................................................... 15

2.7 RS-485 Connector Definition ..................................................................................... 17

3. Operation and Configuration .............................................................................................. 18

3.1 Display Format .......................................................................................................... 18

3.2 OSD Menu Tree ........................................................................................................ 19

3.2.1 G/V/T Model ................................................................................................... 19

3.2.2 P/M Model ...................................................................................................... 22

3.2.3 S6 Model ........................................................................................................ 25

3.3 Configuration Menu ................................................................................................... 28

3.3.1 LANGUAGE ................................................................................................... 29

3.3.2 DEFAULT CAMERA ...................................................................................... 29

3.3.3 BACKLIGHT ................................................................................................... 29

3.3.4 FOCUS .......................................................................................................... 30

3.3.5 AE MODE ...................................................................................................... 33

3.3.6 WBC MODE ................................................................................................... 37

3.3.7 SETUP MENU 1 ............................................................................................. 39

ZOOM SPEED ............................................................................................... 40

DIGITAL ZOOM ............................................................................................. 40

SLOW SHUTTER ........................................................................................... 41

DIGITAL NOISE REDUCTION (P/S Series Model) ........................................ 41

IMAGE INVERSE ........................................................................................... 42

FREEZE ......................................................................................................... 42

APERTURE ................................................................................................... 42

STABILIZER (P/SY/S7/S8 Model) .................................................................. 43

EXIT ............................................................................................................... 43

3.3.8 SETUP MENU 2 ............................................................................................. 44

FLIP ............................................................................................................... 44

OFF ................................................................................................................ 45

ANGLE ADJUSTER ....................................................................................... 45

Orion/3-DN Outdoor

6

PT POSITION (S Series Model) ..................................................................... 45

SPEED BY ZOOM ......................................................................................... 46

AUTO CALI. (Auto Calibration) ....................................................................... 46

PASSWORD (S Series Model) ................................ ....................................... 46

OSD AUTO CLOSE (S Series Model) ............................................................ 48

SYSTEM RESET ........................................................................................... 48

EXIT ............................................................................................................... 48

3.3.9 ID DISPLAY ................................................................................................... 48

3.3.10 TITLE DISPLAY ............................................................................................. 49

3.3.11 TITLE SETTING ............................................................................................. 49

3.3.12 PRESET ........................................................................................................ 51

3.3.13 SEQUENCE ................................................................................................... 52

3.3.14 AUTOPAN ...................................................................................................... 54

3.3.15 CRUISE ......................................................................................................... 56

3.3.16 HOME SETTING ............................................................................................ 57

3.3.17 IR FUNCTION (Removable IR Cut Filter) ....................................................... 59

3.3.18 ALARM SETTING .......................................................................................... 62

3.3.19 ALARM DETECT ........................................................................................... 65

3.3.20 WDR FUNCTION ........................................................................................... 69

3.3.21 PRIVACY MASK ............................................................................................ 70

3.3.22 TIME SETTING .............................................................................................. 75

3.3.23 SCHEDULE ................................................................................................... 76

3.3.24 EXIT OSD ...................................................................................................... 77

Appendix A: Technical Specification ........................................................................................ 78

OSD Menu Notes ......................................................................................................................... 82

<G/V/T Model> ...................................................................................................................... 82

<P/M Model> ................................ ......................................................................................... 85

<S Series (S3/S4/S5/S6/S7/S8/SY/SA/SB) Model> .............................................................. 88

Orion/3-DN Outdoor

7

1. Overview

The Dome Camera delivers up to 432x zoom ratio (T model) to capture clear image in the distance. Continuous Auto Focus, Back Light Compensation, Auto Exposure and Digital Slow Shutter functions are provided for clear and high quality image. Removable IR cut filter ensures 24 hours operation, while Privacy Masks are specially designed to avoid any intrusive monitoring at specific region; all of the salient functions can be incorporated to meet your needs. The Home function allows users to specify a preset position as the ‘home position’ or home functions (Sequence/Auto-pan/Cruise). Under the mode, Dome Cameras can come back to the preset home position or functions when the camera has been idle for a user-defined period of time. Additionally, the unique Schedule function enables users to program a preset point or function (Sequence/Auto-pan/Cruise) so that these actions can be automatically performed in certain period of time.

The Dome Camera provides variable pan/tilt speeds ranging from a fast patrol of 400° per second to a slow ramble of 5° per second with 0.225° pan/tilt accuracy for fast and accurate tracking ability. The 360° endless rotation and

-10°~190° tilt travel make tracking the object passing directly beneath the dome. Maximum 256 preset points can be programmed for precise location of target areas, and users can also define Sequence lines, Auto-Pan lines and Cruise routes for the camera to operate automatically. In addition, RS-485 communication port is available for remote control purposes.

The Integrated High Speed Dome Camera provides 8 alarm inputs and 1 alarm relay output, and the smart alarm management mechanism can be programmed through the OSD setup menu; certain function (Preset/Sequence/Auto-Pan/ Cruise) can be activated when an alarm is triggered.

Large set of built-in protocols provide connectivity to other surveillance systems. The built-in protocols include DSCP, Pelco, VCL, Philips, AD-422, etc, which allow the Dome Camera series to be integrated with other suppliers' surveillance systems.

Orion/3-DN Outdoor

8

1.1 Product Features

Precise and Accurate Performance

 Auto Calibration  Preset accuracy of 0.225°  Preset speed up to 400°/sec.  Proportional Pan & Tilt Speed  Preset Position/Sequence /Auto-Pan /Cruise

Dynamic Applications

 Multi-language OSD  Schedule function  Multiple built-in Protocols  Up to 24 masking zones (Optional)  8 alarm inputs, 1 alarm output  Motion Detection (Optional)  Flexible mountings  Compact lightweight design for easy installation  Weather resistant housing  All-in-one type

Superior Camera Image Quality

 Minimum illumination 0.01 Lux (B/W)  Digital Slow Shutter  Electronic Shutter  Wide Dynamic Range  Auto White Balance  Backlight Compensation  Auto Exposure  Image Inverse  Removable IR Cut Filter  Digital Noise Reduction  Electronic Image Stabilizer (Optional)

Orion/3-DN Outdoor

9

1.2 Product Application

Connect the Dome Camera to other devices as shown in the diagram to complete a video surveillance solution.

NOTE: To extend the network distance up to 1.2 km (4000 feet) and to protect the connected devices, it is highly recommended to place a repeater at the mid-point. However, a repeater may be needed in the network distance less than 1.2 km if the used cables are not the CAT 5, 24-gauge cables; refer to 2.7 RS-485 Connector Definition. Refer to the repeater’s manual for detailed information.

Orion/3-DN Outdoor

10

2. Connecting the Dome Camera

Please refer to the following sections to connect, set and operate the Dome Camera. In order to control the Integrated High Speed Dome Camera, basically a control keyboard or other control device is required.

2.1 Package Contents

Before proceeding, please check the box contains the items listed here. If any item is missing or has defects, DO NOT install or operate the product and contact your dealer for assistance.

Dome Camera with

Outdoor Mount Kit

Data Cable for Power Supply, Video, Alarm and RS-485 (AC 24V)

Waterproof Rubber

M3 Standard Screw (x1)

M3 Security Screw (x1)

M5 Standard Screw (x1)

M5 Security Screw (x1)

Lubricant

Security Torx

Optical Cover

Installation & User

Instructions

Orion/3-DN Outdoor

11

2.2 Switch/Connector Definition

Configuring the Dome Camera’s ID and communication protocol are required before connecting the Dome Camera to other devices. The switches used for configuring these settings are located on the camera’s back plate. Additionally, the 22-Pin Connector for Data Cable connection and ISP Connector for firmware upgrade kit connection are also set on the back plate.

Please refer to the diagram and table accompanied with for use of each switch/connector.

A

Camera Control Protocol Switch

B

Communication Switch

C

None

D

22-Pin Connector

E

ID Switch

F

Reserved

G

ISP Connector (for FW upgrade)

Orion/3-DN Outdoor

12

2.3 Communication Switch Setting

The Dome Camera’s communication switches are specified in the table below.

Communication Switch

SW 1

RS-485 Setting

SW 2

SW 3

Termination

SW 4

Line Lock

SW 5

Factory Default Reset

SW 6

Reserved

RS-485 is the interface that communicates the Dome Camera and its control device; for this reason, the RS-485 setup of the dome and the control device must be the same. The RS-485 default setting is half-duplex (see the diagram follows). Please do not change the default setting without qualified specialist or supplier’s notice. As for the SW 3 and SW 4, they are used for termination and Line Lock adjustment respectively. The SW 5 is mainly used when users want to restore the camera to the factory default status; moreover, once firmware upgrade is carried out, users also need to reset the SW 5 afterward.

RS-485 Setting

Half-duplex

Full-duplex

Orion/3-DN Outdoor

13

2.4 ID Setting

Please change the Dome Camera’s ID if there is more than one Dome Camera on the same installation site. Use the switch to change your Speed Dome Camera’s ID by turning the arrow to the desired number respectively. For instance, if the camera’s ID is 123, the ID switch should be set as below.

NOTE: No two Dome Cameras should be given the same ID, or communication conflict may occur.

Centesimal Digit Decimal Digit Single Digit

NOTE: The number “0” should locate upwards as shown in above diagram for correct switch definition.

Orion/3-DN Outdoor

14

2.5 Camera Control Protocol Setting

Define the protocol you are going to use basing on the devices of your surveillance system. Generally, use one protocol even the devices are provided from different manufacturers. Please refer to the table below for all supported protocols with their matching switch numbers and baud rate and choose a protocol for your Speed Dome Camera.

The table below shows various protocols with their matching switch numbers and baud rate.

Switch No.

Protocol

Baud Rate

00

VCL

9600

01

Pelco D

2400

02

Pelco P

4800

04

Chiper

9600

05

Philips

9600

06

Ernitec*

2400

07

DSCP

9600

08

AD422

4800

09

DM P

9600

11

Pelco D

4800

12

Pelco D

9600

13

Pelco P

2400

14

Pelco P

9600

15

JVC

9600

21

Kalatel-485

9600

22

Kalatel-422

4800

*Only function of Ernitec protocol is fully verified.

Select protocol: Pelco D, with switch no. 01 and baud rate 2400, for instance, the protocol switch should be set as below.

Decimal Digit Single Digit

NOTE: The number “0” should locate upwards as shown in above diagram for correct switch definition.

Orion/3-DN Outdoor

15

2.6 22-Pin Connector Definition

An AC 24V Data Cable is shipped with the Integrated High Speed Dome Camera for a quick installation for demo or testing usage; see the diagram below. The Dome Camera’s 22-pin connector definition will also be specified in the latter part. For more information about RS-485 connector, refer to 2.7

RS-485 Connector Definition.

NOTE: Be careful not to pull the cables improperly during installation. Additionally, it is suggested to fasten the cables after cable connection is completed. Furthermore, when wiring the AC 24V power cable, make sure the Ground wire is inserted into the mid-pin of the terminal block.

Orion/3-DN Outdoor

16

The Dome Camera’s 22-pin connector definition is listed as shown below.

Definition

1

AC 24-1/DC (＋)

12

ALM-1

2

ALM NC

13

ALM-3

3

AC 24-2/DC (－)

14

ALM-2

4

ALM NO

15

ALM-4

5

FG

16

ALM-5

6

ALM COM

17

ALM-6

7

T+

18

ALM-7

8

R-

19

ALM-8

9

T-

20

ALM GND

10

R+

21

VGND

11

ISOG

22

Video

Orion/3-DN Outdoor

17

2.7 RS-485 Connector Definition

RS-485 is the interface that communicates the Dome Camera and its control device. Please connect the control keyboard to the speed dome through the terminal block. The recommended cables for RS-485 communication are CAT 5 cables; maximum cable length for over 24-gauge wire is 4000 feet (1219 meters). If the total cable length exceeds 4000 feet, using a repeater to maintain the signals is recommended. Please refer to the figure and table below for pin definition and wiring.

Corresponding Pins

(22-Pin Connector)

Definition

1

7,10

T+, R+ (D+)

2~4

Reserved

- 5 8,9

T-, R- (D-)

Orion/3-DN Outdoor

18

3. Operation and Configuration

3.1 Display Format

The information shown on the screen is described in terms of OSD display, position and function description in the table below.

Position

Function

OSD Display

Description

1

Motion

MOTION

Alarm Detect Message

2

Alarm

ALARM 1

Alarm Message

3

Focus Modes &

Backlight

A

Auto Focus Mode

M

Manual Focus Mode

X

Back Light Compensation OFF

B

Back Light Compensation ON

4

Booting

Message

XX…(Dome Type); ID: 001 (Default) DSCP/9600 (Default); INITIALIZING

Shows Dome Type, ID Address, Protocol

and Baud Rate

5

Error Message

PAN ERROR TILT ERROE CAM MODULE ERROR

Shows system initializing error message

6

Zoom Ratio

x1

Present Zoom Ratio

(Optical Zoom/Digital Zoom)

7

Title

 Maximum 20 characters for each title.  16 sets of title are available.

8

Camera ID

001

Show the camera ID

9

Time

XXXX/XX/XX XX:XX

Year/Month/Day Hour:Minute

10

Position display

XX YYY/YY

XX: facing direction of PTZ including N, E, Z, W, NE, SE, SW, SN YYY/YY: angle of PZT, 0~359/ 10~-90

Orion/3-DN Outdoor

19

3.2 OSD Menu Tree

The OSD setup menu structure of each model is listed separately in the following section. The star symbol indicates the factory default.

For detailed function description, please refer to 3.3 Configuration Menu.

3.2.1 G/V/T Model

Item

Layer 1

Layer 2

Layer 3

Default

LANGUAGE

ENGLISH

DEFAULT CAMERA

ON

BACKLIGHT

OFF

FOCUS

AUTO

AF MODE <NORMAL>, <INTERVAL>, <ZOOM TRIG>

NORMAL

EXIT + SAVE: YES

MANUAL FOCUS SPEED <01>~<08>

EXIT + SAVE: YES

AE MODE

EXPOSURE COMP.

<OFF>, EXPOSURE VALUE: <-10.5dB> ~ <10.5dB>

OFF

EXIT + SAVE: YES

AE MODE

AUTO

EXIT + SAVE: YES

☆

BRIGHT BRIGHT VALUE <00> ~ <31>

EXIT + SAVE

SHUTTER

SHUTTER SPEED <1/10000>~<1> SEC.

EXIT + SAVE: YES

IRIS

IRIS VALUE <CLOSE>, <F1.6> ~ <F28>

EXIT + SAVE: YES

MANUAL

BRIGHT VALUE: AUTO

SHUTTER SPEED <1/10000> ~ <1>

IRIS VALUE <F1.6> ~ <F28>

GAIN VALUE <-3>dB ~ <28>dB

EXIT + SAVE: YES

EXIT + SAVE

YES

WBC MODE

AUTO (Auto White Balance)

☆

INDOOR

OUTDOOR

ATW (Auto-tracing WBC)

MANUAL R GAIN <000> ~ <127>

B GAIN <000> ~ <127>

EXIT + SAVE: YES

SETUP MENU 1

ZOOM SPEED

<1> ~ <8>

8

DIGITAL ZOOM

ON

SLOW SHUTTER

OFF

IMAGE INVERSE

OFF

FREEZE

OFF

APERTURE

<01> ~ <16>

11

EXIT

YES

SETUP MENU 2

FLIP <OFF>, <M.E.>, <IMAGE>

OFF

EXIT + SET: YES

ANGLE ADJUSTER MIN ANGLE <-10 ~ +10 DEG>

0

MAX ANGLE <080 ~ 100 DEG>

90

EXIT + SET: YES

SPEED BY ZOOM

OFF

Orion/3-DN Outdoor

20

Item

Layer 1

Layer 2

Layer 3

Default

AUTO CALI.

OFF

SYSTEM RESET

YES

EXIT

YES

ID DISPLAY

ON

TITLE DISPLAY

OFF

TITLE SETTING

<01> ~ <16>

1

PRESET

PRESET SET

<001>~<256>

ENTER

PRESET RUN

<001>~<256>

ENTER

EXIT

YES

ENTER

SEQUENCE

SEQUENCE LINE

<1> ~ <8>

1

SEQUENCE POINT

<01> ~ <64>

1

PRESET POS.

<001> ~ <255>, <END>

1

SPEED

<01> ~ <15>

1

DWELL TIME

<000> ~ <127> SEC.

0

RUN SEQUENCE

ENTER

EXIT

YES

AUTOPAN

AUTOPAN LINE

<1> ~ <4>

1

START POINT

END POINT

DIRECTION

RIGHT

SPEED

<01> ~ <04>

1

RUN AUTOPAN

ENTER

EXIT

YES

CRUISE

CRUISE LINE

<1> ~ <8>

1

RECORD START

ENTER

RECORD END

ENTER

RUN CRUISE

ENTER

EXIT

YES

HOME SETTING

HOME FUNCTION

OFF

SELECT MODE

PRESET

PRESET POINT SEQUENCE LINE AUTOPAN LINE CRUISE LINE

<001> ~ <256>

1

<1> ~ <8>

1

<1> ~ <4>

1

<1> ~ <8>

1

RETURN TIME

<1> ~ <128> MIN.

1

GO

ENTER

EXIT

YES

IR FUNCTION <AUTO>

THRESHOLD <01> ~ <29>

AUTO

EXIT + SAVE: YES

<MANUAL> IR MANUAL: <ON>, <OFF>

EXIT + SAVE: YES

ALARM SETTNG

ALARM PIN

<1> ~ <8>

1

ALARM SWITCH

OFF

ALARM TYPE

<NO> (Normal Open), <NC> (Normal Close)

N.C.

ALARM ACTION

PRESET

PRESET POINT SEQUENCE LINE AUTOPAN LINE CRUISE LINE

<001> ~ <256>

1

<1> ~ <8>

1

<1> ~ <4>

1

<1> ~ <8>

1

DWELL TIME

<001> ~ <127> Sec., <ALWAYS>

ALWAYS

EXIT

YES

ALARM DETECT

DETECT SWITCH

OFF

DETECT MODE

ON: <INT FOCUS>, <FIX FOCUS>, <FIX AE>, <MOTION>; OFF: NONE

BLOCK MODE

NONE; MOTION: <ON>, <OFF>

FRAME SET

NONE; MOTION: <01> ~ <04>

FRAME DISABLE

NONE; MOTION: <01> ~ <04>

THRESHOLD

NONE; MOTION: <001> ~ <255>

EXIT

YES

WDR FUNCTION

OFF

PRIVACY MASK

PRIVACY SWITCH

OFF

Orion/3-DN Outdoor

21

Item

Layer 1

Layer 2

Layer 3

Default

TRANSPARENCY

OFF

COLOR

BLACK

SET MASK

<01> ~ <24> H CENTER: L/R

V CENTER: D/U

H SIZE <000> ~ <080>

V SIZE <000> ~ <060>

EXIT + SAVE

CLEAR MASK

<01> ~ <24>

EXIT

YES

TIME SETTING

TIME DISPLAY

OFF

SET YEAR

<00> ~ <99>

SET MONTH

<01> ~ <12>

SET DAY

<00> ~ <31>

SET HOUR

<00> ~ <23>

SET MINUTE

<00> ~ <59>

EXIT+SAVE

SCHEDULE

SWITCH

OFF

POINT

<01> ~ <32>

1

HOUR

<00> ~ <23>

0

MINUTE

<00> ~ <59>

0

MODE

NONE

NO FUNCTION

☆

PRESET

PRESET POINT <001> ~ <256>

SEQUENCE

SEQUENCE LINE <1> ~ <8>

AUTOPAN

AUTOPAN LINE <1> ~ <4>

CRUISE

CRUISE LINE <1> ~ <8>

IR FUNC.

IR FUNCTION <AUTO>, <ON>, <OFF>

SCHEDULE RESET

YES

EXIT

YES

EXIT OSD

YES

Orion/3-DN Outdoor

22

3.2.2 P/M Model

Item

Layer 1

Layer 2

Layer 3

Default

LANGUAGE

ENGLISH

DEFAULT CAMERA

ON

BACKLIGHT

<ON> BLC LEVEL <00> ~ <30>

OFF

EXIT + SAVE: YES

<OFF>

FOCUS

AUTO

TUNING VALUE <1.5M> (P Model only), <1M>, <30CM>, <10CM>, <1CM>

10CM

EXIT + SAVE: YES

MANUAL FOCUS SPEED <0> ~ <3>

EXIT + SAVE: YES

AE MODE

AUTO IRIS OFFSET <00> ~ <15>

☆

EXIT + SAVE: YES

SHUTTER

SHUTTER SPEED M Model: <1/30000> ~ <1/2> (NTSC); <1/30000> ~ <1/1.5> (PAL) P Model: <1/30000> ~ <1/1> (NTSC);

<1/30000> ~ <1/1> (PAL)

EXIT + SAVE: YES

IRIS <00> ~ <09>

EXIT + SAVE: YES

AGC <00> ~ <05>

EXIT + SAVE: YES

WBC MODE

AUTO (Auto White Balance)

☆

MANUAL R GAIN <00> ~ <99>

B GAIN <00> ~ <99>

EXIT + SAVE: YES

SETUP MENU 1

ZOOM SPEED

FAST

DIGITAL ZOOM

OFF

SLOW SHUTTER

P Model: <1/1> ~ <1/60> (NTSC) M Model: <1/2> ~ <1/60> (NTSC)

1/60

P Model: <1/1> ~ <1/50> (PAL) M Model: <1/1.5> ~ <1/50> (PAL)

1/50

D.N.R. (P Model Only)

1

IMAGE INVERSE

OFF

FREEZE

OFF

APERTURE <AUTO>

☆

H APERTURE <00> ~ <31> V APERTURE <00> ~ <31>

STABILIZER (P Model Only)

OFF

EXIT

YES

SETUP MENU 2

FLIP <OFF>, <M.E.>, <IMAGE>(P/M Model)

OFF

EXIT + SET: YES

ANGLE ADJUSTER MIN ANGLE <-10 ~ +10 DEG>

0

MAX ANGLE <080 ~ 100 DEG>

90

EXIT + SET: YES

SPEED BY ZOOM

OFF

AUTO CALI.

OFF

SYSTEM RESET

YES

EXIT

YES

ID DISPLAY

ON

TITLE DISPLAY

OFF

TITLE SETTING

<01> ~ <16>

1

PRESET

PRESET SET

<001>~<256>

ENTER

PRESET RUN

<001>~<256>

ENTER

EXIT

YES

ENTER

SEQUENCE

SEQUENCE LINE

<1> ~ <8>

1

Orion/3-DN Outdoor

23

Item

Layer 1

Layer 2

Layer 3

Default

SEQUENCE POINT

<01> ~ <64>

1

PRESET POS.

<001> ~ <255>, <END>

1

SPEED

<01> ~ <15>

1

DWELL TIME

<000> ~ <127> SEC.

0

RUN SEQUENCE

ENTER

EXIT

YES

AUTOPAN

AUTOPAN LINE

<1> ~ <4>

1

START POINT

END POINT

DIRECTION

RIGHT

SPEED

<01> ~ <04>

1

RUN AUTOPAN

ENTER

EXIT

YES

CRUISE

CRUISE LINE

<1> ~ <8>

1

RECORD START

ENTER

RECORD END

ENTER

RUN CRUISE

ENTER

EXIT

YES

HOME SETTING

HOME FUNCTION

OFF

SELECT MODE

PRESET

PRESET POINT SEQUENCE LINE AUTOPAN LINE CRUISE LINE

<001> ~ <256>

1

<1> ~ <8>

1

<1> ~ <4>

1

<1> ~ <8>

1

RETURN TIME

<1> ~ <128> MIN.

1

GO

ENTER

EXIT

YES

IR FUNCTION

P Model: THRESHOLD <01> ~ <13> M Model: THRESHOLD <MID>, <HI>, <LOW>

AUTO

IR COLOR <B/W>, <COLOR>

EXIT + SAVE: YES

ALARM SETTING

ALARM PIN

<1> ~ <8>

1

ALARM SWITCH

OFF

ALARM TYPE

<NO> (Normal Open), <NC> (Normal Close)

N.C.

ALARM ACTION

PRESET

PRESET POINT SEQUENCE LINE AUTOPAN LINE CRUISE LINE

<001> ~ <256>

1

<1> ~ <8>

1

<1> ~ <4>

1

<1> ~ <8>

1

DWELL TIME

<001> ~ <127> Sec., <ALWAYS>

ALWAYS

EXIT

YES

ALARM DETECT

OFF

WDR FUNCTION

<ON>

RATIO LEVEL <000> ~ <128> SHUTTER SPEED <000> ~ <128> IRIS OFFSET <000> ~ <128> EXIT <YES>

<AUTO>

<OFF>

☆

PRIVACY MASK

PRIVACY SWITCH

OFF

MASK SHADE

BLACK

SET MASK

<01> ~ <08> H CENTER <000> ~ <255>

V CENTER<000> ~ <255>

H SIZE <000> ~ <127>

V SIZE <000> ~ <127>

EXIT + SAVE

CLEAR MASK

<01> ~ <08>, <RESET>

1

MASK DISPLAY

FIRST

EXIT

YES

TIME SETTING

TIME DISPLAY

OFF

SET YEAR

<00> ~ <99>

SET MONTH

<01> ~ <12>

SET DAY

<00> ~ <31>

Orion/3-DN Outdoor

24

Item

Layer 1

Layer 2

Layer 3

Default

SET HOUR

<00> ~ <23>

SET MINUTE

<00> ~ <59>

EXIT+SAVE

SCHEDULE

SWITCH

OFF

POINT

<01> ~ <32>

1

HOUR

<00> ~ <23>

0

MINUTE

<00> ~ <59>

0

MODE

NONE

NO FUNCTION

☆

PRESET

PRESET POINT <001> ~ <256>

SEQUENCE

SEQUENCE LINE <1> ~ <8>

AUTOPAN

AUTOPAN LINE <1> ~ <4>

CRUISE

CRUISE LINE <1> ~ <8>

IR FUNC.

IR FUNCTION <AUTO>, <ON>, <OFF>

SCHEDULE RESET

YES EXIT

YES

EXIT OSD

YES

Orion/3-DN Outdoor

25

3.2.3 S6 Model

Item

Layer 1

Layer 2

Layer 3

Default

LANGUAGE

ENGLISH

DEFAULT CAMERA

ON

BACKLIGHT

<ON>

OFF

<OFF>

FOCUS

AUTO AF MODE <NORMAL>, <Z. TRIG.>, <PTZ TRIG.>

NORMAL

EXIT+SAVE

MANUAL

AE MODE

EXPOSURE COMP. <OFF>, EXPOSURE VALUE: <-10.5dB> ~ <10.5dB>

OFF

EXIT + SAVE: YES

AE MODE

AUTO

BRIGHT VALUE/ SHUTTER SPEED/ IRIS VALUE/ GAIN VALUE: AUTO

AUTO

EXIT + SAVE: YES

SHUTTER

SHUTTER SPEED PAL: <1/50> ~ <1/10000> SEC. NTSC: <1/60> ~ <1/10000> SEC.

EXIT + SAVE: YES

IRIS IRIS VALUE <F1.6>

EXIT + SAVE: YES

MANUAL

BRIGHT VALUE: AUTO

SHUTTER SPEED PAL: <1/50> ~ <1/10000> SEC. NTSC: <1/60> ~ <1/10000> SEC.

IRIS VALUE <F1.6>

GAIN VALUE <-3>dB ~ <28>dB

EXIT + SAVE: YES

EXIT+ SAVE

YES

WBC MODE

AUTO (Auto White Balance)

☆

INDOOR

OUTDOOR

ATW (Auto-tracing WBC)

MANUAL R GAIN <000> ~ <127>

B GAIN <000> ~ <127>

EXIT + SAVE: YES

SETUP MENU 1

ZOOM SPEED

<8>

8

MAX. DIGITAL ZOOM

OFF

SLOW SHUTTER

OFF

D.N.R. 2D N.R. <ON>, <OFF>

ON

3D N.R. <ON>, <OFF>

EXIT + SAVE: YES

IMAGE INVERSE

OFF

FREEZE

OFF

APERTURE

<01> ~ <16>

7

STABLIZER

OFF

EXIT

YES

SETUP MENU 2

FLIP <OFF>, <M.E.>, <IMAGE>

OFF

EXIT + SET: YES

ANGLE ADJUSTER MIN ANGLE <-10 ~ +10 DEG>

0

MAX ANGLE <080 ~ 100 DEG>

90

EXIT + SET: YES

PT POSITION PT DISPLAY

OFF

SET PAN ZERO

EXIT+SET

YES

SPEED BY ZOOM

OFF

AUTO CALI.

OFF

PASSWORD

OFF

OSD AUTO CLOSE

<OFF>, <5> ~ <30> SEC.

20

Orion/3-DN Outdoor

26

Item

Layer 1

Layer 2

Layer 3

Default

SYSTEM RESET SYSTEM RESET <YES>

DEFAULT SYSTEM <YES>

EXIT <YES>

EXIT

YES

ID DISPLAY

ON

TITLE DISPLAY

OFF

TITLE SETTING

<01> ~ <16>

1

PRESET

PRESET SET

<001>~<256>

ENTER

PRESET RUN

<001>~<256>

ENTER

EXIT

YES

ENTER

SEQUENCE

SEQUENCE LINE

<1> ~ <8>

1

SEQUENCE POINT

<01> ~ <64>

1

PRESET POS.

<001> ~ <255>, <END>

END

SPEED

<01> ~ <15>

1

DWELL TIME

<000> ~ <127> SEC.

0

RUN SEQUENCE

ENTER

EXIT

YES

AUTOPAN

AUTOPAN LINE

<1> ~ <4>

1

START POINT

END POINT

DIRECTION

RIGHT

SPEED

<01> ~ <04>

1

RUN AUTOPAN

ENTER

EXIT

YES

CRUISE

CRUISE LINE

<1> ~ <8>

1

RECORD START

ENTER

RECORD END

ENTER

RUN CRUISE

ENTER

EXIT

YES

HOME SETTING

HOME FUNCTION

OFF

SELECT MODE

PRESET

PRESET POINT SEQUENCE LINE AUTOPAN LINE CRUISE LINE

<001> ~ <256>

1

<1> ~ <8>

1

<1> ~ <4>

1

<1> ~ <8>

1

RETURN TIME

<1> ~ <128> MIN.

1

GO

ENTER

EXIT

YES

IR FUNCTION

AUTO THRESHOLD <MID>, <HI>, <LOW>

LOW

EXIT + SAVE: YES

MANUAL IR MANUAL: <ON>, <OFF>

EXIT + SAVE: YES

ALARM SETTING

ALARM PIN

<1> ~ <8>

1

ALARM SWITCH

OFF

ALARM TYPE

<NO> (Normal Open), <NC> (Normal Close)

N.C.

ALARM ACTION

PRESET

PRESET POINT SEQUENCE LINE AUTOPAN LINE CRUISE LINE

<001> ~ <256>

1

<1> ~ <8>

1

<1> ~ <4>

1

<1> ~ <8>

1

DWELL TIME

<001> ~ <127> Sec., <ALWAYS>

ALWAYS

ALARM PRIORITY

<1> ~ <8>

1

EXIT

YES

ALARM DETECT

DETECT SWITCH

OFF

DETECT MODE

<MOTION> BLOCK MODE

NONE; MOTION: <ON>, <OFF>

FRAME SET

NONE; MOTION: <01> ~ <04>

Orion/3-DN Outdoor

27

Item

Layer 1

Layer 2

Layer 3

Default

FRAME DISABLE

NONE; MOTION: <01> ~ <04>

THRESHOLD

NONE; MOTION: <001> ~ <255>

EXIT

YES

WDR FUNCTION

OFF

PRIVACY MASK

PRIVACY SWITCH

OFF

TRANSPARENCY

OFF

COLOR

BLACK

SET MASK

<01> ~ <16> H CENTER: L/R

V CENTER: D/U

H SIZE <000> ~ <080>

0

V SIZE <000> ~ <060>

0

EXIT + SAVE

CLEAR MASK

<01> ~ <16>

1

EXIT

YES

TIME SETTING

TIME DISPLAY

OFF

SET YEAR

<00> ~ <99>

SET MONTH

<01> ~ <12>

SET DAY

<00> ~ <31>

SET HOUR

<00> ~ <23>

SET MINUTE

<00> ~ <59>

EXIT+SAVE

SCHEDULE

SWITCH

OFF

POINT

<01> ~ <32>

1

HOUR

<00> ~ <23>

0

MINUTE

<00> ~ <59>

0

MODE

NONE

NO FUNCTION

☆

PRESET

PRESET POINT <001> ~ <256>

SEQUENCE

SEQUENCE LINE <1> ~ <8>

AUTOPAN

AUTOPAN LINE <1> ~ <4>

CRUISE

CRUISE LINE <1> ~ <8>

IR FUNC.

IR FUNCTION <AUTO>, <ON>, <OFF>

SCHEDULE RESET

YES

EXIT

YES

EXIT OSD

YES

(*) For SY/ S7/ S8 Model Only.

ERNITEC Orion/3-DN Outdoor Installation & User's Instructions

Specifications and Main Features

Frequently Asked Questions

User Manual