Erika K250 Installation Manual

Cookie former

FM128 K250…K600

Operating instruction SELECTRONIC-A

(Translation of Original Operating Instruction)

Version:

jan_anl_K250_600_04_2013_en.indd

04_2013_en

Niederrheinische Formenfabrik

Gerh. Janssen & Sohn GmbH & Co. KG

Moerser Straße 33 • D 47798 Krefeld
Tel. [phone] • Fax [phone]
www.nff-janssen.de • [e-mail]

»Congratulations to your new cookie machine.«

Contents

Operating instruction

page contents

4 Safety regulations and security precaution

5 Proper use

5 Food hygiene

6 Operating instruction

11 SELECTRONIC-A control

15 Drive schematic FM 128 K

15 Defects and their repairs

16 Connection and assignment

17 Technical Data

18 EC Declaration of Conformity

Attachment

A1 Annex: General for dough

Recipes

Operation with baking paper

3

Treatment recommendation for shiny blue sheets

A2 Annex: Spare parts list K250…600 Selectronic-A

A Annex: Maintenance instructions for replacing belts

A Annex: Operating instruction for knife installation

A Annex: Operating instruction for knife guard installation

A Annex: Operating instruction for sliding ring and sliding pin

Niederrheinische Formenfabrik
Gerh. Janssen & Sohn GmbH & Co. KG

Safety regulaions and security precautions

Machine is ready to use, as it is supplied.
Disconnect plug when attendance or repair machine.

Before you begin, read operating instructions!

The machines of type FM 128 K 250, 300, 400, 450, 580 and 600, are tted with the
following safety equipment:

Security precaution of rollers

In front of the roller is mounted a Plexiglas cover in front of the funnel with a hinge.
The Plexiglas cover is held laterally by guide rails.

Security precaution of knife

The machine has a knife guard, which automatically lays down on the knife when you
open the dough hopper and thus excludes an injury.

Security precaution of hopper

The hopper is equipped with a safety switch that shuts off all the movements while
lifting. It is impossible to manipulate the safety switch.

Scurity precaution of lift grid

The machine stops immediately when you open the grid above the hopper.

Security precaution of transport belt guard

The transport belt for the back plate is provided with an inlet protection.

4

All protective covers and panels are bolted and can only be
opened with tool!

Proper use

As the name molding machine already says, the machine is suitable for forming short­bread like biscuits, spekulatius, milanese and cakebases (for cream cakes and other
cakes, lattice of dough (for tarts), tartelettes, brezel, linzer, kipferl, etc.
White cakes, brown cakes, gingerbread, and marzipan can be formed by special
rollers.

Food hygiene

The machine should be stored in a dry place. As a cover, we recommend a linen tape.
Please do not use a plastic cover, because it may arise a humid climate under the
cover, which can lead to mold and vermin infestation.
The linen tape should be cleaned or exchanged as required (dry cleaning).

After use, it is important to clean the machine.
Clean all interior and exterior surfaces, corners and edges which are accessible with a
lint-free cloth.
Intermediate the lint-free cloth in warm soap water, before further wipe.

Do not steam clean or use a jet of water.

The machine has to be isolated from mains supply before carrying out
any cleaning!

5

Operating instruction

Congratulations to your new cookie machine.

1. Unpacking the machine

If you nd a damage on the unpacked machine, call your agent and let him see the
damage, so that the damaged machine can be replaced.

2. Connect the machine

Before plugging the machine, get sure, that electricity network has a voltage
of 3 x 400V + MP + protective conductor. the machine is set by this specifcation.

With 3 x 230 + MP + protection manager, the engine of the machine is reversed ac­cordingly. If you have the correct voltage with the appropriate socket, you can let the
machine run on trial basis. If the machine is running backward, stop the engine imme­diately and disconnect the power plug from the can.The machine is wired clockwise. It
is banned to manipulate the clockwise rotation of connection.

Let, if necessary, your socked change by a licensed electrician!

If the machine is permanently connected without a rm plug, the machine needs an
additional main switch.

6

3.1. Beltregulation / upper transport belt

The upper transportbelt, wich takes the gures from the knife, can be adjusted by hex
nut M18 on spindle thread on both sides. Please regulate only few and do not tighten
the belt too fast, because the belt takes some minutes to regulate.
If possible take always just one side to regulate, because otherwise the tension of the
belt greatly increases unnecessarily. The belt gets narrow and snatches in extreme

rase.

3.2. Beltregulation / lower tranport belt

The lower transport belt must not be adjusted.
They are connected by connectors and can be exchanged easily.

4.1. Speed regulation of transport belt

The speed of the lower transport belt can be in connection with the speed of the ma­chine, regulated by Selectroniccontrol.