
INSTRUCTION SHEET
High Performance CADDY® CAT HP
J-Hook Assemblies
Fig. 1
Fig. 8
Retainer Installation
Fig. 2
Fig. 9
Fig. 3
Fig. 10
Fig. 4
Fig. 11
Fig. 5
Fig. 12
Fig. 6
Fig. 13
Fig. 7
Fig. 14
Features:
- For use with Data Communication Cables only.
- Each assembly comes with a retainer.
- The CAT64HP holds 4-pair UTP cables; 300 Cat.5/5e or 300 fiber optic cables, or 185 Cat.6 cables.
- Provides strain relief and routes cables. Bend radius conforms to EIA®/TIA-568-A standard.
- Complies with UL®, cUL®, and NEC® requirements for structured cabling systems
- Complies with 1997 EIA/TIA 569-A.
WARNING:
ERICO products shall be installed and used only as indicated in ERICO product instruction sheets and training materials. Instruction sheets are available at
1.
www.erico.com
ERICO products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.
2.
All instructions must be
3.
Improper installation, misuse, misapplication or other failure to completely follow ERICO's instructions and warnings may cause product malfunction, property
4.
damage, serious bodily injury and death.
Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment.
5.
All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any
6.
other purpose.
NOTE: All load ratings are for static conditions and do not account for dynamic loading such as wind, water or seismic loads, unless otherwise noted.
The customer is responsible for:
a. Conformance to all governing codes.
b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified
engineer.
c. Using appropriate industry standard hardware as noted above.
SAFETY INSTRUCTIONS:
All governing codes and regulations and those required by the job site must be observed.
Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.
EIA is a registered service mark of Electronic Components Association.
NEC is a registered trademark of, and National Electrical Code (NEC) standard is a copyright of the National Fire Protection Association, Inc.
UL and cUL are registered trademarks of UL LLC.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
TECHNICAL SUPPORT:
www.erico.com
and from your ERICO customer service representative.
completely
followed to ensure proper and safe installation and performance.
CFS462_F
1 OF 6
© 2011, 2012, 2013, 2014 ERICO
International Corporation.

INSTRUCTION SHEET
High Performance CADDY® CAT HP
J-Hook Assemblies
Angle Brackets
Beam Clamp
Fig. 1
1) Position CATHPAB onto joist,
wall or concrete
2) Secure with appropriate fastener
Figure 2
Figure 3
1) Place on beam and tighten screw securely
(Approximately 20 in. lbs. torque)
2) Place cables in J-hook
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
TECHNICAL SUPPORT:
www.erico.com
CFS462_F
2 OF 6
© 2011, 2012, 2013, 2014 ERICO
International Corporation.

INSTRUCTION SHEET
High Performance CADDY® CAT HP
J-Hook Assemblies
Flange Mount Clip
Figure 4
1) With hammer, tap
clip onto flange
Figure 9
2) Place cables in J-hook
Drop Wires, Rods and Flanges
Figure 5
1) Squeeze fastener
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
TECHNICAL SUPPORT:
www.erico.com
CFS462_F
2) Connect top edge over wire
3) Twist into place
4) Release
3 OF 6
© 2011, 2012, 2013, 2014 ERICO
International Corporation.
5) Place cables in
J-hook

INSTRUCTION SHEET
INSTRUCTION SHEET
High Performance CADDY® CAT HP
J-Hook Assemblies
Floor Pedestal Support
Figure 6
1) Position clip on pedestal
2) Tighten screw through clip
with 75 in-lb torque.
3) Place cables in J-hook
Figure 7
1) Place on beam and
Figure 8
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
TECHNICAL SUPPORT:
www.erico.com
tighten screw securely
(Approximately
20 in. lbs. torque)
2) Place cables in J-hook
CFS462_F
4 OF 6
© 2011, 2012, 2013, 2014 ERICO
International Corporation.

INSTRUCTION SHEET
High Performance CADDY® CAT HP
J-Hook Assemblies
Figure 10
Purlin
Figure 11
1) With hammer, tap clip onto flange
2) Place cables in J-hook
Strut
Fig. 12
1) Hand push clip onto flange
2) Place cables in J-hook
Position clip onto strut.
1.
Rotate downwards until secure on strut.
2.
Fig. 13
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
TECHNICAL SUPPORT:
www.erico.com
CFS462_F
5 OF 6
© 2011, 2012, 2013, 2014 ERICO
International Corporation.

INSTRUCTION SHEET
High Performance CADDY® CAT HP
J-Hook Assemblies
Fig. 14
Place on beam and tighten screw securely
1.
(Approximately 40 in. lbs. torque)
Place cables in J-hook
2.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
TECHNICAL SUPPORT:
www.erico.com
CFS462_F
6 OF 6
© 2011, 2012, 2013, 2014 ERICO
International Corporation.