ERICO CADDY ROD LOCK Beam Clamp User Manual
INSTRUCTION SHEET
CADDY
Part
Number
CRLB37EG
CRLB37EG
CRLBM8EG
CRLBM8EG
CRLBM10EG
CRLBM10EG
Part
Number
CRLB37EG*
CRLBM8EG**
CRLBM10EG*
CADDY ROD LOCK beam clamp not for use with hot dip galvanized threaded rod.
*CRLB37EG and CRLBM10EG Beam Clamps are FM® Approved when installed in method #1 & #2 orientations.
*CRLB37EG and CRLBM10EG Beam Clamps are listed per UL® 2239 and UL 203 in method #1 & #2 orientations.
**CRLBM8EG is listed per UL 2239 only in method #1 & #2 orientations.
**CRLBM8EG and CRLBM10EG Beam Clamps are VdS approved when installed in method #1 and #2 orientations (VdS Approval Number G412036).
-Beam
I
tapered
flanges
®
Article
Number
N/A
N/A
390001
390001
390002
390002
&
**
Method #1
ROD LOCK Beam Clamp
Article
Number
N/A
390001
390002
Description
3/8" CADDY® ROD LOCK Beam Clamp
3/8" CADDY ROD LOCK Beam Clamp
M8 CADDY ROD LOCK Beam Clamp
M8 CADDY ROD LOCK Beam Clamp
M10 CADDY ROD LOCK Beam Clamp
M10 CADDY ROD LOCK Beam Clamp
Description
3/8" CADDY ROD LOCK Beam Clamp
M8 CADDY ROD LOCK Beam Clamp
M10 CADDY ROD LOCK Beam Clamp
-Beam
I
non-tapered
flanges
RS
3/8"
3/8"
M8
M8
M10
M10
RS
3/8"
M8
M10
Method #1
T
1/8" - 3/16"
1/4" - 3/8"
3mm - 5mm
6mm - 10mm
3mm - 5mm
6mm - 10mm
F
250 lbs
500 lbs
1,100 N
1,400 N
1,100 N
2,200 N
Max. Pipe diameter
supported by clamp &
threaded rod
4"/DN100
DN50
4"/DN100
RS
T
F
Method #1
Bar Joist
Method #2
Method #2
Method #2
Method #2
Method #1
WARNING:
ERICO products shall be installed and used only as indicated in ERICO product instruction sheets and training materials. Instruction sheets are available at
1.
www.erico.com
ERICO products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.
2.
All instructions must be
3.
Improper installation, misuse, misapplication or other failure to completely follow ERICO's instructions and warnings may cause product malfunction, property
4.
damage, serious bodily injury and death.
Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment.
5.
All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any
6.
other purpose.
NOTE: All load ratings are for static conditions and do not account for dynamic loading such as wind, water or seismic loads, unless otherwise noted.
The customer is responsible for:
a. Conformance to all governing codes.
b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified engineer.
c. Using appropriate industry standard hardware as noted above.
SAFETY INSTRUCTIONS:
All governing codes and regulations and those required by the job site must be observed.
Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.
FM is a registered certification mark of FM Approvals LLC, LTD
UL is a registered trademark of UL LLC.
VdS is a registered trademark of VdS Schadenverhütung GmbH.
CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
TECHNICAL SUPPORT:
www.erico.com
and from your ERICO customer service representative.
completely
followed to ensure proper and safe installation and performance.
CFS410_R
1 OF 2
© 2009, 2010, 2011, 2012 ERICO International Corporation
Method #2
Method #1
INSTRUCTION SHEET
CADDY
Method #1
* Arrows on CADDY
1
As shipped
4
®
ROD LOCK Beam Clamp
®
ROD LOCK Beam Clamps must always point up.
Rotate counter clockwise
2
2 full turns to insert rod
Push rod
5
into beam clamp.
3
Hand tighten top
6
locknut.
Tighten the set screw with
60 in-lb(6.8 N-m). Tighten the
jam nut.
Method #2
* Arrows on CADDY
1
®
ROD LOCK Beam Clamps must always point up.
Rotate counter clockwise
2
2 full turns to insert rod
Top of rod must be
positioned at or above
top of locknut
Rod adjustment
7
possible after
locknut tightened.
4
3
Tighten the set screw with
60 in-lb(6.8 N-m). Tighten
the jam nut.
As shipped
TECHNICAL SUPPORT:
www.erico.com
CFS410_R
2 OF 2
Follow installation steps 5-7
from method #1.
© 2009, 2010, 2011, 2012 ERICO International Corporation
Loading...