ERICO 561177 Instruction Sheet
INSTRUCTION SHEET
INSTRUCTION SHEET
SBF4C1600AL
SBF4C1600AL
561177
561177
TOP
IEC 60947-7-1
1000 VAC / 1500 VDC
Uimp = 12kV; Ipk = 105 kA
Icw kA rms 1s = 96
110.9mm
4.36in
1800 A
UL 1953
1680 A
1000 V AC/DC
SCCR up to 100kA*
AL or CU Conductor
IP20
95% Fill Ratio
Halogen Free
UL 94 V-0
BOTTOM
5mm
.2in
No. Terminals
1
2 (TOP)
2 (BOTTOM)
No. Terminals
176.0mm
6.93in
164.7mm
6.48in
Conductor
ERIFLEX FLEXIBAR**
Conductor
IEC 60947-7-1
Size
6X50X1 to
10X80X1
35 mm² to
300 mm²
UL 1953
Size
DIA
23.5 mm
DIA
39.2mm
1.54in
39.2mm
1.54in
Torque
42.4 N-m
Torque
99.1mm
3.90in
For voltage
measurement only.
6-32 UNC-2B
9 in-lbs [1.0 N-m]
4 mm² /12 AWG max
Strip Length
50 mm
38 mm
70 mm
Strip Length
Hex
10 mm
Hex
63 - 80 mm wide FLEXIBAR
1
2 (TOP)
2 (BOTTOM)
NOTE:
*Refer to UL file E497276.
1.
**Includes ERIFLEX FLEXIBAR Advanced
2.
For multiple phase assemblies, join blocks together before installing onto DIN profile and use one conduit per phase for both line and load. For a higher SCCR rating,
3.
fasten and support conductors within 8 inches of the blocks.
When mounted on DIN profile, end stops should be used on both ends of gangable blocks.
4.
For IEC, the cable must be secured within 15 cm of the terminal.
5.
WARNING:
nVent products shall be installed and used only as indicated in nVent product instruction sheets and training materials. Instruction sheets are available at
1.
www.nVent.com
nVent products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.
2.
All instructions must be
3.
Improper installation, misuse, misapplication or other failure to completely follow nVent's instructions and warnings may cause product malfunction, property
4.
damage, serious bodily injury and/or death, and void your warranty.
SAFETY INSTRUCTIONS:
All governing codes and regulations and those required by the job site must be observed.
Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.
nVent, CADDY, ERICO CADWELD, ERICO CRITEC, ERICO, ERIFLEX, and LENTON are owned by nVent or its global affiliates. All other
trademarks are the property of their respective owners. nVent reserves the right to change specifications without prior notice.
TECHNICAL SUPPORT
www.nVent.com
ERIFLEX FLEXIBAR**
and from your nVent customer service representative.
completely
6X50X1 to
10X80X1
2/0 AWG to
600 kcmil
followed to ensure proper and safe installation and performance.
IP8394_A
0.92 in
375 in-lbs
1 OF 1
2.0 in
1.5 in
2.75 in
© 2018 nVent All Rights Reserved
3/8 in
50 - 63 mm wide FLEXIBAR
Loading...