ERICO 429 User Manual
INSTRUCTION SHEET
INSTRUCTION SHEET
®
Finish:
Electro-galvanized Zinc
®
UL listed for use with CPVC pipe as a
hanger and surge restraint
Installation:
- Insert pipe
- Close pipe clamp by pressing
the clamp part upward
3/8
Threaded Rod
Part Number
4290050EG
4290075EG
!
4290100EG
!
4290125EG
!
4290150EG
!
4290200EG
!
4290250EG
4290300EG
4290350EG
4290400EG
*
4290500EG
*
=FM Approved
!
Threaded Rod
Part Number
!
!
!
!
!
®
*
CPVC Non-Insulated Pipe Clamp
M10
595052
595053
595054
595056
595057
595059
595061 596060
595062 596062
M12
Threaded Rod
Part Number
*
*
595063 596063
595066
*
=Not UL Listed
*
Nominal
Pipe Size
Inches
1/2
3/4
1
1-1/4
1-1/2
2
2-1/2
3
3-1/2
4
5
Outside Dia.
Of Pipe
(Inches)
/ mm
(0.84) / 21.3
(1.05) / 26.7
(1.32) / 33.4
(1.67) / 42.2
(1.90) / 48.3
(2.37) / 60.3
(2.87) / 73
(3.50) / 88.9
(4.00) / 101.6
(4.50) / 114.3
(5.56) / 141.3
- Let screw head lock
in the tabs
- Use a screwdriver to
tighten the two screws
- Tighten pipe clamp
until tabs are parallel
Bottom Beam Installation
WARNING:
ERICO products shall be installed and used only as indicated in ERICO product instruction sheets and training materials. Instruction sheets are available at
1.
www.erico.com and from your ERICO customer service representative.
ERICO products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.
2.
All instructions must be completely followed to ensure proper and safe installation and performance.
3.
Improper installation, misuse, misapplication or other failure to completely follow ERICO's instructions and warnings may cause product malfunction, property
4.
damage, serious bodily injury and death.
Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment.
5.
All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any
6.
other purpose.
NOTE: All load ratings are for static conditions and do not account for dynamic loading such as wind, water or seismic loads, unless otherwise noted.
The customer is responsible for:
a. Conformance to all governing codes.
b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified engineer.
c. Using appropriate industry standard hardware as noted above.
SAFETY INSTRUCTIONS:
All governing codes and regulations and those required by the job site must be observed.
Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.
All rights reserved. CADDY, CADWELD, CRITEC, ERICO, ERIFLEX, ERITECH, and LENTON are registered trademarks of ERICO International Corporation.
FM is a registered certification mark of FM Approvals LLC, LTD
UL is a registered trademark of Underwriters Laboratories, Inc.
TECHNICAL SUPPORT:
www.erico.com
Top Beam Installation
CFS397_H
1 OF 1
4.52 Nm
40 inch-lbs
To comply with UL203 Listing in the top beam installation the hex
nut of the pipe hanger must be inserted onto a threaded rod and
rest directly on the structural member.
© 2009, 2010, 2011 ERICO International Corporation
Loading...