ASSEMBLY INSTRUCTIONS
LX Sit-Stand Wall Mount LCD Arm
25 lbs
(11.3 kg)
180°
180°
360°
20"
(508 mm)
Maximum Screen
Size* = 42”
*Limited to 25 lbs
maximum
70°
ENGLISH
5°
0° or 360°
For the latest User Installation Guide please visit: www.ergotron.com
User's Guide - English
Guía del usuario - Español
Manuel de l’utilisateur - Français
Gebruikersgids - Deutsch
Benutzerhandbuch - Nederlands
Guida per l’utente - Italiano
Användarhandbok - svenska
ユーザーガイド:日本語
用户指南 : 汉语
888-45-275-W-01 rev.J • 02/17
1 of 20
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly
installed on the product before attempting adjustments. This product should move smoothly and easily through the
full range of motion and stay where you set it. If movements are too easy or diffi cult or if product does not stay in
desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your
product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed
from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps
to ensure safe and optimum operation.
Tools Needed
Concrete Wall Mounting
Ø 3/8” (10mm)
ENGLISH
2
1
13 mm
Stud Finder
Wood Stud Mounting
Ø 3/16" (5mm)
2 of 20
888-45-275-W-01 rev.J • 02/17
Components
ABCD
1x
4x
1x
1
4x
M5 x 7mm
1x
4x
1x
2
1x
10-24 x 1/2"
2x
3
4x
M4 x 10mm
4x
ENGLISH
2x
M4 x 10mm
2x
1x
4
2x
5
1/8"
M3 x 6mm
2x
M8
M8 x 80mm
1x
4mm
1x
5mm
2x
M6 x 45mm
M8 M5 Kit
4x
M5x20mm
M6
4x 4x 4x
4x
6
M8-M5
2x
M4x12mm M5x12mm M6x12mm
Reducer
888-45-275-W-01 rev.J • 02/17
3 of 20
Mounting Height for Ergonomic Workstation
1
This mounting height is a recommendation for an ergonomic workstation that accommodates user heights of 5’4”-5’9”
(163-175cm).
If user heights are di erent than this, you should change mounting height to accommodate user heights. (Change mounting height one inch for every one inch di erence in user heights).
Mounting height assumes there is a 6” (152 mm) distance between the center of your monitor mounting holes and the top of the screen. If your distance is smaller, you should increase mounting height
6”
(152 mm)
accordingly, if your distance is larger, you should decrease your mounting height accordingly.
ENGLISH
37.5”
(953mm)
Determine mounting location:
Front view with arm pushed back against the wall.
20”
(516mm)
5’4” - 5’9”
(163-175cm)
5’4” - 5’9”
(163-175cm)
41”
(1041mm)
Top view showing range of motion when pulled out from the wall.
4 of 20
22”
(562mm)
0.2”
(5mm)
(32mm)
27.6”
(701mm)
1.3”
10.2”
(259mm)
4.2”
(106mm)
888-45-275-W-01 rev.J • 02/17
2
1.34"
(34mm)
6.5"
(165mm)
3.15"
(80mm)
1.57"
(40mm)
5.1"
(129mm)
1.14"
(29mm)
7.1"
(180mm)
WARNING: Ensure that the wall structure is capable
of supporting four times the total weight of mounted
equipment. Mounting to wall surfaces that do not meet
this criteria may result in an unstable, unsafe condition
which could lead to personal injury and/or property
damage. Consult a construction professional if you
have any doubt about what this means in regard to
your particular application.
CAUTION: Make sure the wall mount bracket is level,
ush and snug to the wall surface. DO NOT OVERTIGHT-
EN THE BOLTS.
Ergotron product
6
Wood
Concrete
ENGLISH
7 8
888-45-275-W-01 rev.J • 02/17
5 of 20
4x
10-24 x 5/8"
NOTE: Wall Track and Brackets sold separately.
NOTE: Fasteners may unwind due to vibration caused by movement of mounting solution over time. Inspect mounting solution
for loose fasteners on a routine basis. If desired, apply a light duty
thread locking adhesive to fasteners before installation to prevent
back-out.
4x
10-24 x 1/2"
1/8"
10
ENGLISH
1/8"
When attaching to Pole Clamps, use 10-24 x 5/8”
screws included with pole brackets, Do NOT use
10-24 x 1/2” screws
10
4x
1/8"
10-24 x 1/2"
6 of 20
10
888-45-275-W-01 rev.J • 02/17
Wood Stud Mounting
2
d
a b c
Stud Finder
Optional locking feature
(customer supplied lock)
2.75”
ENGLISH
3
b
2x
M8 x 80mm
Ø 3/16" (5mm)
c
13 mm
CAUTION: Make sure the wall mount
bracket is level, ush and snug to the
wall surface.
DO NOT OVERTIGHTEN
THE BOLTS.
4
10
888-45-275-W-01 rev.J • 02/17
7 of 20
Concrete Wall Mounting
2
a b c
3-1/8"
(80 mm)
Ø 3/8” (10mm)
WARNING:
Mounting holes must be at least 3-1/8” (80mm) deep and must be located within solid concrete, not mortar or covering material.
If you drill into an area of concrete that is not solid, reposition mounting holes until both anchors can be fully inserted into solid
concrete!
ENGLISH
WARNING:
Anchors that are not fully set in solid concrete will not support the applied load resulting in an unstable, unsafe condition which
could lead to personal injury and/or property damage. Consult a construction professional if you have any doubt about what this
means in regard to your particular situation.
8 of 20
888-45-275-W-01 rev.J • 02/17
1
2
Concrete Wall Mounting
3
a
2x
Optional locking feature
(customer supplied lock)
b
M8 x 80mm
2x
ENGLISH
c
888-45-275-W-01 rev.J • 02/17
13 mm
CAUTION: Make sure the wall mount
bracket is level, ush and snug to the
wall surface.
DO NOT OVERTIGHTEN
THE BOLTS.
4
10
9 of 20
4
Mount extension and arm to wall bracket.
CONTAINS GREASE.
Use bag to protect hands
from getting greasy.
824-369-00
c
ENGLISH
a
NOTE: when
sliding sleeve
on to bracket,
align slot over
rotation stop.
b
Do Not
Overtighten
Cap Screw!
M6 x 45mm
4mm
Top View
M6
M6
M6 x 45mm
4mm
+=
10 of 20
Do Not
Overtighten
Cap Screw!
Rotation Stop
on Bracket
Slot
in Sleeve
888-45-275-W-01 rev.J • 02/17
Sleeve on
Bracket
5
Portrait / Landscape Options
OPTION i If you want full portrait/landscape rotation, skip to step 8 on the next page.
OPTION ii If you do not want your TV/Monitor to rotate all all, you can stop rotation by inseting
the set screw.
iii
0˚
ENGLISH
M3 x 6mm
888-45-275-W-01 rev.J • 02/17
6
12
11 of 20
6
Check size of
TV/Monitor hole
pattern
TV/Monitor Hole
Pattern Sizes
VESA Adapter
Con gurations
100mm (3-15/16”)
75mm (2-15/16”)
100mm (3-15/16”)
75mm (2-15/16”)
ENGLISH
A
B
75x75mm
100x100mm
100mm (3-15/16”)
13
200mm (7-7/8”)
100x200mm
14
200mm (7-7/8”)
C
D
200x200mm
14
200x100mm
14
200mm (7-7/8”)
200mm (7-7/8”)
100mm (3-15/16”)
12 of 20
888-45-275-W-01 rev.J • 02/17
7
Mount Type A TV/Monitor to Arm
A
75x75mm
100x100mm
4x
M4 x 10mm
100mm (3-15/16”)
75mm (2-15/16”)
100mm (3-15/16”)
75mm (2-15/16”)
M4 x 10mm
ENGLISH
888-45-275-W-01 rev.J • 02/17
OR
M4 x 10mm
16
8
13 of 20
7
Mount VESA Adapters to Arm based on TV/Monitor hole
pattern size (B, C, or D) .
BCD
ENGLISH
4x
M5 x 7mm
14 of 20
888-45-275-W-01 rev.J • 02/17
7
Mount Type B, C, or D TV/Monitor to Arm
B
100mm (3-15/16”)
200mm (7-7/8”)
C
200mm (7-7/8”)
200mm (7-7/8”)
M4x12mm
D
200mm (7-7/8”)
M5x12mm
M6x12mm
100mm (3-15/16”)
ENGLISH
NOTE: To reduce M8
holes for use with M5
screws, or if you have a
model with Samsung
holder rings, follow the
M8M5 KIT instructions
on the next page.
888-45-275-W-01 rev.J • 02/17
16
M4x12mm
M5x12mm
OR
M6x12mm
OR
16
8
15 of 20
M8M5 KIT Instructions
NOTE: follow this step only if your TV/monitor has M8 holes which need to be reduced
to M5 or for Samsung models using the holder ring.
Install M8M5 reducer bushing to TV/Monitor and use M5 x 20 mm
monitor screws to secure when using the Samsung holder ring.
TV/Monitor Mounting
M8 size hole
Attach top
8
and bottom
ENGLISH
bracket
covers
M5 x 20mm
Monitor Screw
M8M5 Reducer Bushing
Holder Ring
(Not included *Samsung Only)
To remove covers:
a) Wedge the blade of a at screwdriver into the gap between the wall mount bracket and the cover.
Rotate the blade upward to pry the cover away.
b) Repeat on the opposite side of the wall mount bracket.
c) Once the cover is free on both sides, lift it o .
Top Cover
Bottom Cover
16 of 20
aa
bb
cc
888-45-275-W-01 rev.J • 02/17
9
a
Organize and route cables
1x
1x
b
ENGLISH
c
888-45-275-W-01 rev.J • 02/17
17 of 20
Adjustment Step
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is
properly installed on the product before attempting adjustments. This product should move smoothly and easily
through the full range of motion and stay where you set it. If movements are too easy or diffi cult or if product
does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements.
Depending on your product and the adjustment, it may take many turns to notice a difference. Any time
equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you
should repeat these adjustment steps to ensure safe and optimum operation.
10
ENGLISH
To adjust the arm lift:
5mm
CAUTION: DO NOT overtighten fasteners.
Overtightening may cause damage to your
equipment.
5mm
WARNING
WARNING! Stored Energy Hazard: The arm mechanism is under tension and will move up rapidly, on its own, as
soon as attached equipment is removed. For this reason, DO NOT remove equipment unless the arm has been
moved to the highest position! Failure to follow this instruction may result in serious personal injury and/or
equipment damage!
18 of 20
Increase Lift Strength
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or
this product does not stay down when
lowered, then you'll need to decrease
Lift Strength:
888-45-275-W-01 rev.J • 02/17
11
To adjust the TV/monitor tilt:
4mm
CAUTION: DO NOT remove screw. Removing
screw may cause damage to equipment.
4mm
ENGLISH
Increase Lift Strength
If the mounted weight is too heavy or
this product does not stay up when
raised, then you'll need to increase
Lift Strength:
Decrease Lift Strength
If the mounted weight is too light or
this product does not stay down when
lowered, then you'll need to decrease
Lift Strength:
888-45-275-W-01 rev.J • 02/17
19 of 20
Set Your Workstation to Work For YOU!
Learn more about ergonomic computer use at:
www.computingcomfort.org
Height Position top of screen slightly below eye level.
Position keyboard at about elbow height with wrists at.
Distance Position screen an arm's length from face—at least 20” (508mm).
Position keyboard close enough to create a 90˚ angle in elbow.
Angle Tilt screen to eliminate glare.
Tilt the keyboard back 10° so that your wrists remain at.
To Reduce Fatigue
Breathe - Breathe deeply through your nose.
Blink - Blink often to avoid dry eyes.
Break • 2 to 3 minutes every 20 minutes
• 15 to 20 minutes every 2 hours.
ENGLISH
For Warranty visit: www.ergotron.com/warranty
For Service visit: www.ergotron.com
For local customer care phone numbers visit: http://contact.ergotron.com
20 of 20
© 2015 Ergotron, Inc. All rights reserved.
888-45-275-W-01 rev.J • 02/17
Loading...