Page 1
1 of 8
300-5577-00 rev. J • 10/16
Product Part#
Elevate II 48w 29d MVBD48SS/xx
Elevate II 60w 29d MVBD60SS/xx
Built with Anthro-DNA™
For the latest User Installation Guide please visit: www.ergotron.com
ASSEMBLY INSTRUCTIONS
Elevate™ II
Single Surface Table
Page 2
2 of 8
300-5577-00 rev. J • 10/16
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical furnishing, basic precautions should always be followed, including the
following. Read all instructions before using Elevate II.
DANGER
To reduce the risk of electric shock, always unplug this furnishing from the electrical outlet
before cleaning.
WARNING
To reduce the risk of burns, re, electric shock, or injury to persons:
1. Unplug from outlet before putting on or taking of parts.
2. Close supervision is necessary when this furnishing is used by or near children, invalids, or disabled persons.
3. Use this furnishing only for its intended use as a described in these instructions. Do not use attachments not
recommended by the manufacturer.
4. Never operate this furnishing if it has a damaged cord or plug, if it is not working properly, if it has been dropped or
damaged, or dropped into water. Any damage to the electrical system must be examined & repaired by a qualified
electrician.
5. Keep the cord away from heated surfaces.
6. Do not use outdoors.
7. Do not operate where aerosol (spray) products are being used or where oxygen is being administered.
8. To disconnect, remove plug from outlet.
9. The control box and legs have no user-serviceable parts and must be replaced by components from Anthro.
10. Power cord moves up and down with the table. Make sure power cord moves freely through all positions
of the desk.
11. Protect the power cord from damage when moving the desk.
12. Maximum load is 150 lbs.
SAVE THESE INSTRUCTIONS
CONSIGNES DE SÉCURITÉ IMPORTANTES
En cas d’utilisation de mobilier alimenté électriquement, il est important de respecter certaines
précautions de base, notamment celles décrites ci-dessous. Lire intégralement les consignes avant
d'utiliser ce mobilier.
DANGER
Pour limiter le risque de choc électrique, toujours débrancher le mobilier avant de nettoyer.
AVERTISSEMENT
Pour limiter les risques de brûlure, d’incendie, de choc électrique ou de blessure aux personnes :
1. Débrancher avant d'installer ou de retirer des pièces.
2. Une surveillance étroite est nécessaire lorsque ce mobilier est utilisé par ou à proximité des enfants, des personnes invalides
ou handicapées.
3. Utiliser ce mobilier uniquement pour l’usage auquel il est destiné, tel que détaillé dans ces consignes. Ne pas utiliser
d’accessoires non recommandés par le fabricant.
4. Ne jamais utiliser ce mobilier si un cordon ou une prise électrique est endommagé, ou s’il ne fonctionne pas correctement,
s’il a été échappé ou endommagé ou s’il est tombé dans l'eau. Tout dispositif électrique endommagé doit être évalué et
réparé par un électricien qualifié.
5. Maintenir le cordon électrique à l’écart de toute source de chaleur.
6. Ne pas utiliser à l’extérieur.
7. Ne pas utiliser où des produits aérosols (pulvérisateurs) sont utilisés ou lorsque de l’oxygène est administré.
8. Mettre le mobilier hors tension en débranchant de la prise.
9. Le boîtier de commande et les pieds ne comportent aucun élément réparable par l’utilisateur et doivent être exclusivement
remplacés par des composants Anthro.
10. Le cordon d'alimentation monte et descend avec la table. Veuillez vous assurer que le cordon d'alimentation soit libre de se
déplacer quelle que soit la position du bureau.
11. Protéger le cordon d'alimentation contre tout dommage lors du changement de position du bureau.
12. La charge maximale est de 68 kg.
CONSERVEZ CES CONSIGNES
Page 3
3 of 8
300-5577-00 rev. J • 10/16
01
03
04
05
06
07
08
10 11
12
13
19
# Component Quantity Part Number
01 Worksurface 1
48w 29d 101-1108-03-00
60w 29d 101-1107-03-00
02 Gusset X (not shown) 1 225-4611-00
03 Gusset Y 1 225-4612-00
04 Electric Leg 2 575-5085-00
05 Motor Housing 2 225-4613-00
06 Cross Pan 1
48w 225-4619-00
60w 225-4615-00
07 Cable Tray 1
48w 29d 225-4625-00
60w 29d 225-4624-00
08 Control Box 1 400-5506-00
09 Power Cord (not shown) 1 400-5181-00
10 Key Pad 1 400-5357-00
11 Key Pad Slider 1 400-5358-00
12 Foot 2 835-5556-00
13 3/4" Button-head MDF Screw 31 325-5575-00
14 M6-10 Button-head Screw 8 325-5503-00
15 M6x14 Flat-head Screw 4 325-5435-00
16 3/4" Phillips SMS Zinc Screw 4 325-5370-00
17 1/2" Button-hd Screw 3 325-5193-00
18 10-24 Nylock Nut 3 325-5186-00
19 M6-20 Cap Screw 8 325-5272-00
20 Control Box Cable (not shown) 2 400-5182-00
21 1.75" Phillips SMS Pan-hd Screw 2 325-5772-00
(not shown)
WELCOME
Thank you for purchasing Anthro's Elevate
II electric lift table!
If you have any questions or if we can
help you in any way, please contact us at
800.325.3841.
TOOLS
Your Elevate II comes with these tools:
• 5/32" hex Anthro driver
• 5/32" hex driver bit
• 5mm hex key
• 1/8" hex key
• 3-way wrench
PARTS LIST
Before beginning assembly of your table, please review
the parts list to verify that your shipment is complete.
Page 4
4 of 8
300-5577-00 rev. J • 10/16
3/4" Button Hd PB Screw
325-5575-00
A
B
M6-10 Button-head Screw
325-5503-00
C
D
M6x14 Flat Hd Screw
325-5435-00
3/4" Button Hd PB Screw
325-5575-00
E
STEP 1 - ATTACH GUSSETS TO TOP
Lay the worksurface upside down on a cushioned, non-marring surface.
Locate the front edge of the table. On Plus tables, the front of the table
has a sloping waterfall edge. On the Basic tables, the back edge of the
table has the seam where the edgebanding meets.
Align the Leg Gussets with the holes on the top so the upright ange faces
the outside of the table and the tapering end points to the front of the
table.
Attach each gusset to the worksurface with six 3/4" Button Hd PB Screws
(325-5575-00) using the Anthro driver.
STEP 2 - INSTALL LEGS
Align one Leg with one Leg Gusset so the cord feeds out of the
Leg toward the center of the table. The Leg will rest on top of the
Gusset's button-head screws, so it may feel a little wobbly. [A]
Slide a Leg Housing over the Leg and down until it covers the Leg
Motor and the six screw holes on the housing line up with the six
pre-drilled holes on the shelf. [B]
Move to the front of the table and attach the front of the Housing
to the Leg with two M6-10MM Button Hd Screws (325-5503-00)
using the Anthro driver. Tilt the leg slightly to align the holes. [C]
Loosely attach the Housing to the shelf with six 3/4" Button Hd PB
Screws (325-5575-00). [D]
Attach the side of the Leg to the Leg Gusset with two M6-14 Flat-
head Screws (325-5435-00). [E]
Repeat for the other Leg and Housing.
Page 5
5 of 8
300-5577-00 rev. J • 10/16
M6-10 Button-head Screw
325-5503-00
3/4" Button Hd PB Screw
325-5575-00
3/4” Phillips Screw
325-5370-00
3/4" Button Hd PB Screw
325-5575-00
1.75” Phillips Screw
325-5772-00
Step 4 - INSTALL CONTROL BOX AND KEYPAD
Align the Control Box with the four pre-drilled holes on the
worksurface behind the cross pan so you can see the ports on
the Control Box through the openings on the cross pan. On 48"
wide tables, the Control Box is installed at the center of the pan.
On 60" wide tables (shown), the Control Box is installed either
left or
right of center.
Attach the Control Box to the shelf with two 1.75" Phillips SMS
Pan-hd Screws (325-5772-00) using a Phillips screwdriver.
The keypad is installed at the front of the table, either at the left
edge or the right edge. Choose a location, just remember that
the table's upside down now, so when you ip the table over, the
keypad will be on the opposite side.
Align the keypad and its slider housing with the four pre-drilled
holes at the front of the keyboard surface so the buttons are
face-down at the front edge of the keyboard surface and the at
side of the housing is against the shelf. The keypad can also be
installed directly to the worksurface without the slider housing,
either so it extends in front of the table or so it's set back a bit.
Using four Phillips Head Screws (325-5370-00), attach the keypad
and its housing (if desired) to the front of the worksurface.
Install these screws by hand. Too much torque can damage the
plastic.
Go to Step 5.
STEP 3 - INSTALL THE CROSS PAN
Align the Cross Pan with the Leg Assemblies so the pair of anges
on the pan line up with the pre-drilled holes on the table. Attach
the back of the pan to the top with four 3/4" Button Hd PB Screws
(325-5575-00)
Attach the front of the pan to the top with
three more 3/4" Button Hd PB Screws (325-5575-00).
Attach the pan to each Leg Housing with two M6-10MM Button Hd Screws
(325-5503-00) using the Anthro driver.
Tighten all fasteners.
Keypad and Housing
Attaching the Control Box to the worksur-
face of a 60" wide table.
Page 6
6 of 8
300-5577-00 rev. J • 10/16
M6-20 Cap Screw
325-5272-00
Nylock Nuts
325-5186-00
1/2”Button-hd Screw
325-5193-00
48w Table
Shown without Control Box for easier view.
Side View
Step 5 - INSTALL CABLE TRAY
Align the Cable Tray with the back of the table so the holes on the threaded posts on the cross pan line up with
the holes on the cable tray. Attach the tray to the pan with three Nylock Nuts using your own 3/8" socket or the
3-way wrench provided. (The plastic end of the nut faces up.)
Connect a 1-meter Control Box Cable to each leg cable, then plug each into a port on the Control Box through
the opening in the support pan. Feed extra cable length through an opening in the support pan so it's organized
in the Cable Tray.
Route the Keypad's cable back to the Cross Pan and plug it into the Control
Box. Feed extra cable length through an opening in the support pan so
it's organized in the Cable Tray.
Plug the Power Cord into the Control Box.
Use the provided cable clips to route and organize cords. Install one cable
clip next to the Leg Gusset for the Keypad Cord. Install the other clip next
to the Cross Pan for the Control Box Cables.
Step 6 - INSTALL FEET AND HOME THE LEGS
Align one foot with each leg so the wheels are at the back. Attach the foot
to the leg with four M6x20 Socket-head Screws using the Anthro driver.
Repeat for the other foot.
With the help of another person, carefully rotate the table onto its feet. Plug
in the table and use the keypad to move the table all the way down.
Release the button and press it again to home the legs so they move in
unison.
Add your equipment and route cords into the cable tray. Carefully move the
table through its entire range of motion to be sure that your power and
data cables are long enough.
CONGRATULATIONS! YOUR ELEVATE II ASSEMBLY IS COMPLETE!
Page 7
7 of 8
300-5577-00 rev. J • 10/16
RATINGS
Electrical Rating
Voltage rating: 120Vac, 60 Hz. When desk is moving with rated load: 400W. When desk is not moving: less than
100mW.
Temperature Ratings
Ambient temperature: 41 degrees F to 140 degrees F. Storage temperature: -4 degrees F to 158 degrees F.
Acclimate table to ambient temperature before use.
Load Rating
Elevate II has a weight capacity of 150 lbs of distributed load.
Duty Cycle
Elevate II has a 10% duty cycle. This provides 6 minutes of movement per hour or two minutes of continuous
use at full load. Once the table reaches its duty cycle, the table shuts down to cool; this usually takes about 20
minutes. Duty cycle is reduced when the load exceeds approved weight limit or temperature is outside the stated
range.
SAFETY CHECK
Plug in the table and home the legs. To home the legs, move the table to its lowest position, release the DOWN
button, then press and hold the DOWN button for 5 seconds. The table will bump a few times, then rest.
Raise the table to its highest position. Watch all the cords and cables as the table moves to verify that cords aren't
wrapped around anything and that nothing interferes with the movement of the table.
Every time you add equipment onto the table, route cords into the cable tray. Carefully move the table through
its entire range of motion to be sure that your power and data cables are long enough. Check the area around
your table for obstructions below, beside, and above the table to be sure there are no collisions.
Verify that the load is distributed evenly across the table.
Moving the table
Keep your equipment safe: remove equipment from the table before you move it.
Before moving the table, lower the table all the way down.
To move the table, lift the surface enough to get the front feet o the ground, and roll it into place.
Lift (don't roll) the table over thresholds, transitions, or bumps.
Page 8
8 of 8
300-5577-00 rev. J • 10/16
© 2016 Ergotron, Inc. All rights reserved.
All trademarks are the property of their respective companies. Anthro is a registered trademark and brand of Ergotron Inc.
Anthro-DNA is a trademark of Ergotron Inc.
For local customer care phone numbers visit: http://contact.ergotron.com
For Service visit: www.ergotron.com
For Warranty visit: www.ergotron.com/warranty
TROUBLESHOOTING GUIDE
Is the table giving you trouble? Try these steps rst. Still need help? Contact Anthro at 800.325.3841.
Table won't go up, but it will go down.
Inspect the leg cables, control box cable, and power cable to be sure they are connected properly and not
damaged. Need replacements? Contact Anthro at 800.325.3841.
Lower the table to its lowest position, release the button, the press the DOWN button again for 5 seconds to
home the legs. The table will bump a few times, then rest.
Table won't move at all: no up, no down.
Has the table exceeded its duty cycle, moving more than 6 minutes per hour or 2 minutes continuously? If so,
rest the table for 20 minutes and try again.
Inspect the leg cables, control box cable, and power cable to be sure they are connected properly and not
damaged. Contact Anthro for replacements.
Test the cables:
• Unplug the Leg Cable that is plugged into Port 1 of the control box.
• Push the DOWN button for 3 seconds and then the UP button for 3 seconds.
• Unplug the Power Cord from the Control Box.
• Plug the Leg Cable back into Port 1.
• Plug the Power Cord back into the Control Box.
• Push the DOWN button and hold until the table reaches its lowest position and stops, then release.
• Push the DOWN button again and hold for 5 seconds.
• Push the UP button to verify the that the table goes up.
Desk will only go up a few inches...then stop...then up another few inches...then stop again.
Verify that the load on the table does not exceed its 150 lbs lift capacity.
Cleaning instructions?
Clean the table with a mild detergent and a soft cloth.
Loading...