
Built with Anthro-DNA™
ASSEMBLY INSTRUCTIONS
Steve's Station Essential
Product Part#
Steve's Station Essential, 60w RAD260GV-xx
Steve's Station Essential, 72w RAD272GV-xx
NOTE: The Monitor Extensions, CPU Holders, displays, and hardware are not included.
300-5610-00 rev. D
• 09/18
1

WELCOME!
Thank you for purchasing Steve's Station Essential from Anthro!
PARTS LIST
Before beginning assembly of your Steve's Station Essential table, please review the parts list to verify that
your shipment is complete.
Product Quantity Part Number
26
22
08
02
14
34
10
33
04
05
16
19
01 Keyboard Surface 1 101-1147-03-00
02 Monitor Surface 1 101-1148-03-00
03 Side Surface X 1
60w table 101-1149-03-00
72w table 101-1159-03-00
04 Side Surface Y 1
60w table 101-1150-03-00
72w table 101-1160-03-00
05 Monitor Boom Tube 2 125-5404-03
06 Side Shelf Support X 1 500-1100-56
07 Side Shelf Support Y 1 500-1101-56
08 Cross Tube 1 500-1102-61
09 Cable Trough 1 500-1103-56
10 Adjusta Mechanism 36" 1 225-5546-00
11 Control Box (not shown) 1 400-0953-00
12 Power Cord (not shown) 1 400-5181-00
13 Leg Control Cables (not shown) 2 400-5182-00
14 Keypad 1 400-5357-00
15 Leg 2 575-5087-00
16 Monitor Easy Track Mast Y 1 835-5635-00
17 Monitor Easy Track Mast X 1 835-5636-00
18 Foot 2 835-5637-00
19 Wire Management Clip 5 175-5188-00
20 5/16-18x x 1 Socket Cap Screw 4 325-5136-00
21 M6x20mm Socket Hd Cap Screw 8 325-5272-00
22 #8 x 3/4" Phillips Flat Hd Screw 4 325-5370-00
23 M6x14 Flat Head Cap Screw 4 325-5435-00
24 M6x10mm Button Hd Cap Screw 8 325-5503-00
25 #10-9x3/4" Button Head PB Screw 90 325-5575-00
26 M8-1.25x10 Socket Hd Cap Screw 4 325-5542-00
27 1/4-20x5/8" Button Hd Cap Screw 6 325-5019-00
28 Keypad Slider (not shown) 1 400-5358-00
29 Brake Release Assembly 1 835-5638-03
30 Mount Release Arm X 1 225-4808-00
31 Mount Release Arm Y 1 225-4809-03
32 #8-32 UNF x 3/8 Hex Button Hd
Cap Screw w/Nylon Patch 8 325-5423-00
33 Monitor Bracket Assembly 1 RADKN-01
34 Monitor Track, 12" 1 225-4442-00
35 Block 1 225-4443-00
36 Knuckle Assembly, Standard 1 RADKNA-02
2
2
03
06
25
36
35
20
17
01
27
24
18
21
31
29
23
07
09
15
300-5610-00 rev. D
30
• 09/18

TOOLS
The following tools are provided for this assembly. If you choose to use a power drill, set the torque setting to midrange.
5/32" hex Anthro driver 3/16" hex looped T-handle 5mm hex key 6mm hex key
1/4" hex key 3/32" hex key 5/32" hex driver bit
STEP 1A
ASSEMBLE THE ADJUSTA MECHANISM
Your Adjusta mechanism comes unassembled and
is boxed separately inside the package. Locate the
small bag of hardware included with the Adjusta
Mechanism. It includes (1) Post, (1) Cotter Pin, (2)
Hex Nuts, (2) Wood Screws, and (2) Cable Mounts.
Begin to assemble the mechanism by rst locating
the Crossbar and Brake/Paddle assembly and
position them as shown at right. Depress the
Paddle once to free the Brake Shaft.
Place the Brake Shaft between the two center
Crossbar anges. Insert the Post through both
center Crossbar anges and the Brake Shaft.
Crossbar
Post
(included with
225-5548-00)
Brake Cable
Center Crossbar
Brake/Paddle Assembly
Flanges
Post
Brake
Shaft
Install the Cotter Pin through the single opening of
the post to secure it in place.
STEP 1B
ASSEMBLE ADJUSTA ARMS
Unpack the remaining Adjusta mechanism
components and arrange them as shown at right.
Place one Crossbar End onto the lower Crossbar
Button and Threaded Bolt located on each Arm
Mechanism. Secure the Crossbar to the Arm
Mechanism using one 5/16" Hex Nut onto the
Threaded Bolt.
Repeat for remaining Crossbar End and Arm
Mechanism.
Brake/Paddle
Arm Mechanism
(included with 225-5548-00)
Cotter Pin
Assembly
Crossbar
Cotter Pin
Arm Mechanism
Paddle
NOTE: it is very important that you attach the
Crossbar ONLY to the Lower Crossbar Button.
300-5610-00 rev. D
• 09/18
5
/16" Hex
Nut
Lower Crossbar
‘Button’
Threaded
Bolts
3

STEP 2
ATTACH ADJUSTA MECHANISM TO MONITOR SURFACE
Loosely attach each Mechanism Arm to the Monitor
Surface using a total of twelve 3/4" Button-hd PB
Screws (325-5575-00).
Align the Paddle Brake Assembly with the six holes
Mechanism Arm
on the Monitor Surface. It may be necessary to
depress the paddle in order to position the brake.
Secure the brake assembly with six more 3/4" Button-hd PB Screws.
3/4" Button Hd PB Screw
325-5575-00
STEP 3
ATTACH ADJUSTA MECHANISM TO KEYBOARD SURFACE
Slide the Keyboard Surface under the mechanism
arms. Align the three holes on each end of the
Keyboard surface with the three holes on each
mechanism arm. Secure the arms to the Keyboard
Surface with six 3/4" Button-hd PB Screws.
Position the Paddle on the Keyboard Surface so the four holes on the
Paddle align with the four holes on the Keyboard Surface and the brake
cable runs under the Adjusta Bar. Secure the Paddle to the Keyboard
Surface with four 3/4" Button-hd PB Screws.
Paddle Brake Assembly
Mechanism Arm
Install one cable clip into the pre-drilled hole next to the Brake Assembly
and route the brake paddle cord through it.
3/4" Button Hd PB Screw
325-5575-00
4
300-5610-00 rev. D
• 09/18