Page 1
User's Guide
Auto Retractable Keyboard Assembly
for use with Ergotron products:
25-022
60-593
CAUTION:
Product is shipped with a stop screw that MUST be removed before use.
DO NOT REMOVE STOP SCREW BEFORE ATTACHING KEYBOARD TRAY.
Failure too follow these instructions will cause equipment damage.
www.ergotron.com |
888-97-057-W-00 rev. C • 08/19
USA: 1-800-888-8458
|
Europe: +31 (0)33-45 45 600
|
China: 400-120-3051
|
Japan: japansupport@ergotron.com
1 of 7
Page 2
Max Weight Capacity
A
2.5 lbs
(1.14 kg)
Minimizing Vertical Lift Storage Profile
For keyboard to fit under the monitor when in storage position, follow these guidelines:
Dimension “A” must be no greater than 7-7/8" (200 mm).
NOTE: Keyboard needs to attach to the lowest set of holes as shown in Step 3
Centerline of Four-Hole
VESA FDMI Pattern
Rear of Monitor
Max Keyboard Depth
(178 mm)
<7"
ABCDE
1x
1
1x
1x
4x
M4 x 12mm
1x
3/32"
1x
2x 2x2x
2
1x
1x
Depending on the design of your VL, you may need any one or combination
of these 4 tools to remove your keyboard tray and pivot.
3/16"
3/32"
3x
2.5mm
8-32 x 1/4"
3/8"
2 of 7
888-97-057-W-00 rev. C • 08/19
Page 3
1
2
a
b
Depending on the design
of your VL, you may need
any one or combination of
these 4 tools to remove your
keyboard tray and pivot.
3/32"
3/8"
c
2.5mm
Save these
screws for
use in steps
3a and 3c.
3
a
c
b
Attach pivot screws to
middle set of holes (third
up from the bottom
set) so pivot attaches at
lowest position.
d
888-97-057-W-00 rev. C • 08/19
Tighten all 4 screws
3 of 7
Page 4
4
a
REMOVE STOP SCREW BEFORE USE.
b
Product is shipped with a stop screw
4x
M4 x 12mm
CAUTION:
that MUST be removed before use.
DO NOT REMOVE STOP SCREW BEFORE
ATTACHING KEYBOARD TRAY.
Failure too follow these instructions will
cause equipment damage.
4 of 7
c
888-97-057-W-00 rev. C • 08/19
Page 5
5
a
Top tray must be
removed for pivot to
function properly.
Remove and discard.
3/32"
b
2x
8-32 x 1/4"
6
7
Attach the loop (soft) side of the velcro to the
bottom of the mouse tray to eliminate rattle
when the tray is stowed upright.
a
3/32"
a
d
e
b
1x
c
3/32"
bc
f
g
Auto-rise Tension
a
8
888-97-057-W-00 rev. C • 08/19
2x
Follow these
instructions to tighten
or loosen tension.
1. Mount all Equipment
(keyboard, wrist rest,
mouse pad, mouse, ect.).
2. Tighten screw slowly
(turn clockwise) until tray
auto rises to full up position.
Screw may require several turns
h
i
Route mouse cable as shown.
5 of 7
Page 6
Remove Auto-rise
NOTE: If you would like to remove the auto-rise feature:
1. Mount all Equipment
(keyboard, wrist rest, mouse pad, mouse, ect.).
2. Loosen screw to decrease the tension
(turn counter clockwise) until the tray
no longer auto-rises.
Minimum Weight Capacity
> 0.75 lbs
(0.34 kg)
The equipment mounted to the
tray must equal 0.75 lbs (0.34 kg)
or greater for the tray to stay down
with no auto rise.
Tilt
b
Tighten both screws for less keyboard tilt.
Loosen both screws for more keyboard tilt.
NOTE: Adjust both screws equally.
You may need to adjust lift tension after equipment has been added or removed.
c
It is important that you adjust this product according to the weight of the mounted equipment as described in the following steps. Any time equipment is
added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and
optimum operation.
Adjustments should move smoothly and easily through the full range of motion and stay where you set it. If adjustments are di cult and do not stay in the
desired position, follow the instructions to loosen or tighten the tension to create a smooth, easy adjustment motion. Depending on your product and the
adjustment, it may take several turns to notice a di erence.
Lift – Up and down
Follow these instructions to tighten or loosen tension.
3/16"
12 3
6 of 7
888-97-057-W-00 rev. C • 08/19
Page 7
For the latest User Installation Guide please visit: www.ergotron.com
For Warranty visit: www.ergotron.com/warranty
For Service visit: www.ergotron.com
For local customer care phone numbers visit: http://contact.ergotron.com
www.ergotron.com |
© 2011 Ergotron, Inc. All rights reserved.
USA: 1-800-888-8458
|
Europe: +31 (0)33-45 45 600
|
China: 400-120-3051
|
Japan: japansupport@ergotron.com
888-97-057-W-00 rev. C • 08/19
7 of 7
Loading...