Ergotron 61-080-085 User Manual
www.ergotron.com
User's Guide - English
Guía del usuario - Español
Manuel de l’utilisateur - Français
Gebruikersgids - Nederlands
Benutzerhandbuch - Deutsch
Guida per l’utente - Italiano
Användarhandbok - svenska
ユーザーガイド : 日本語
用户指南 : 汉语
StyleView Sit-Stand VL
Patient Room
A
< 25 lbs
(11.34 kg)
B
< 5 lbs
(2.27 kg)
C
< 5 lbs
(2.27 kg)
A+B+C< 30lbs. (13.61 kg)
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is
properly installed on the product before attempting adjustments. This product should move smoothly and easily
through the full range of motion and stay where you set it. If movements are too easy or di cult or if product
does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements.
Depending on your product and the adjustment, it may take many turns to notice a di erence. Any time
equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you
should repeat these adjustment steps to ensure safe and optimum operation.
ENGLISH
Max weight 30 lbs (13.61 kg)
CAUTION: DO NOT EXCEED MAXIMUM LISTED
WEIGHT CAPACITY. SERIOUS INJURY OR
PROPERTY DAMAGE MAY OCCUR!
888-61-043-G-01 rev. E • 01/16
Reduce.Reuse.Recycle
1 of 13
Hazard Symbols Review
Symbol Signal Word Level of Hazard
These symbols alert users of a safety condition that
demands attention. All users should be able to
recognize and understand the signi cance of the following Safety Hazards if encountered on the product
or within the documentation. Children who are not
able to recognize and respond appropriately to Safety
Alerts should not use this product without adult
supervision!
NOTE
CAUTION
WARNING
ELECTRICAL
A NOTE indicates important information that helps you
make better use of this product.
A CAUTION indicates either potential damage to
hardware or loss of data and tells you how to avoid the
problem.
A WARNING indicates either potential for property damage, personal injury, or death.
An Electrical indicates an impending electrical hazard
which, if not avoided, may result in personal injury, re
and/or death.
Safety
WARNING: Because surfaces vary widely and the ultimate mounting method is out of Ergotron’s control, it is imperative that you consult
with appropriate engineering, architectural or construction professional to ensure that your Ergotron mounting solution is mounted
properly to handle applied loads.
ENGLISH
CAUTION: Make sure the wall mount bracket is level, ush and snug to the wall surface. DO NOT OVERTIGHTEN THE BOLTS.
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly
installed on the product before attempting adjustments. This product should move smoothly and easily through the full
range of motion and stay where you set it. If movements are too easy or di cult or if product does not stay in desired
positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the
adjustment, it may take many turns to notice a di erence. Any time equipment is added or removed from this product,
resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and
optimum operation.
2 of 13
888-61-043-G-01 rev. E • 01/16
Components
AB C D
1x
1
2
3
4
5
1x 2x
1x
1x
1x
1x1x
WALL MOUNTING TEMPLATE
4x
M8 x 80mm
4x
M8
4x
4x
2x
14x 4x
M4 x 10mm M4 x 14mm
ENGLISH
1x
6
10x
M3 x 5mm
1x
7
2x
8
Tools Needed
13mm
1/2"
4x
1/4-20 x 1.5”
4x
4x
1x
M4 x 10mm
HOLLOW WALL
Ø 1/2” (13 mm)
2
1
WOOD
Ø 7/32" (5.5 mm)
Ø 1/2" (13 mm)
Stud Finder
CONCRETE
Ø 3/8" (9.5 mm)
888-61-043-G-01 rev. E • 01/16
3 of 13
Mounting Height for Ergonomic Workstation
This mounting height is a recommendation for an ergonomic workstation that accommodates user heights of
5’10”-5’11” (178-180cm).
If user heights are di erent than this, you should change mounting height to accommodate user heights.
(Change mounting height one inch for every one inch di erence in user heights).
Mounting height assumes there is a 6” (152 mm) distance between the center of your monitor
mounting holes and the top of the screen. If your distance is smaller, you should increase mounting
6”
(152 mm)
height accordingly, if your distance is larger, you should decrease your mounting height accordingly.
ENGLISH
5’10” - 5’11”
(178-180cm)
42”
(1066mm)
4 of 13
888-61-043-G-01 rev. E • 01/16
Loading...