Ergomat ErgoPerfect NS100W User Manual And Assembly Instructions

NS100W

User Manual/Assembly Instructions

User manual – ErgoPerfect® NS100W height adjustable table

Congratulations! You are now the owner of the new ErgoPerfect® NS100W height adjustable table!

This new, modern, electrically-controlled, height adjustable table, is designed for use in office or industrial assembly
environments. The table is intended for use as a height adjustable work station. The height adjustment function makes it
possible to vary working posture, bringing ergonomic improvements to the workplace.

We recommend that you read the user manual carefully before using the table. Please note: Prohibitions, warnings and
good advice on ergonomics! The user manual should be kept with the table!

How the table works

The height adjustment function works by means of an electric spindle motor. The spindle is activated by a control box,
which is connected to a service panel. The control box has an overload protection device that ensures that the up/down
function is cut off if the table is overloaded.

Instructions for use

The height adjustment function can only be activated from the control panel that is fitted to the underside of the table
top. The panel has two buttons. The table will move as long as pressure is applied to one of the buttons.

The table has no on/off switch and can only be switched off at the mains contact.

Take care when adjusting table height (danger of crushing).

In case of malfunction or similar, see the Troubleshooting Guide in this manual.

Maintenance

The table is in principle maintenance-free. If necessary, all parts may be wiped with a slightly damp cloth and mild soapy
water. Internal parts may not be cleaned. Never use cleaning products on electrical parts. Never spray/apply oil to the
table lifting columns as this will damage the mechanism.

Assembly

The table must be fitted to a plane and strong wall (concrete/brick).

For safety reasons, we recommend the following:

Regular checks that the wall bracket is correctly fixed to the wall. •

After fitting, the wall-mounted table lifting columns must be reset by adjusting the table to its lowest position.
(To reset: push both buttons simultaneously. The columns lower the table to its lowest position.) Then raise the table to
make space for attaching the cable tray. The table is now ready for use.

Make sure that the table has been reset before fitting the cable tray. If, subsequently, the table has to be
reset, please note that the cable tray must be removed before resetting the table.

Ergonomics

Once the table is installed, check that it can easily be raised and lowered, that there are no hindrances to stepless •
movement over the entire range of movement.
Remember: change working posture at regular intervals. Try raising or lowering the table just a couple of •
centimetres at regular intervals. Varying posture is key to minimising the risk of strain and injury.
Vary sitting posture from a seated position with thighs horizontal to a higher seat height with a slanted chair •
seat, sloping thighs and open hip position.
Recommendation: use a chair with a sliding seat angle, which encourages you to tip the chair, reducing the risk •
of developing a slipped disc.
Remember: standing puts less strain on the back than sitting.•

2

Prohibitions, warnings and good advice

Failure to comply with or observe all assembly, safety and operation instructions and warnings regarding the use of this
height adjustable table may result in serious physical injury!

The height adjustable table is not intended for lifting people.•
The height adjustable table may not be installed on a slant or in an otherwise unstable position. If the floor is not •
plane, the table can be levelled using the levelling screws on the table feet.
Do not damage or crush the supply cable!•
The table is designed for maximum 2 minutes’ continuous activation, or maximum 6 minutes activation per •
hour.
Please note: Height adjustment function presents a danger of crushing! This applies in particular to the area •
under the table (cross-bar and any furniture on castors) and the immediate area around the table top (e.g.
shelving, window sills and neighbouring tables).
The entire table top must be free standing, at least 25 mm from shelving, window sills, other tables and •
obstructions.
Check that cables of connected products are long enough. Carefully adjust the table to highest and lowest •
positions.
To reduce electricity consumption, switch off at the mains (e.g. at night).•

Repairs

Repairs should be carried out by an authorised technician. None of the table parts may be repaired by the consumer!
For repairs: Please contact Ergomat A/S.

Warranty

All products in the ErgoPerfect® NS-table series are guaranteed 2-years against defects in manufacture and materials
that are a result of the normal use of the height adjustable table. The right of return does not apply in the case of defects,
damage, or wear and tear that is either directly or indirectly caused by incorrect assembly, incorrect use or other actions
that are not described in the user manual.

Disposal

The table must be disposed of as follows:

Table top must be sent for incineration.­The metal table frame must be deposited as recyclable metal.­Electronic parts must be deposited as electrical scrap.-

Technical specifications

Dimensions: 130 x 61 x 70 cm
Weight: 33.2 kg (without table top)
Electrical connection: 230 V 50 Hz
Output consumption: Max. load: 2 x 140 watts
Electrical consumption (standby): 2.5 W
Load: Maximum lifting capacity 100 kg, evenly distributed on table top and table frame.
Height range: 20 cm
Speed: 50 mm per second, not loaded
Operation: Connected to mains supply 230 V 50 Hz.

The table may be activated max. 2 minutes continuously, or max. 6 minutes in one hour.

Troubleshooting Guide for height-adjustable table

The table does not work:

Check the mains plug – is it switched on?­Check the supply cable: is it connected to the control box?­Check the control box: are the cables connected?­Check the control panel: are the cables connected?-

3