EMPRO-WM175B
Flat Panel Swing Out Arm
Congratulations on purchasing the EMPRO-WM175B
Mount. This is shipped with all proper installation
hardware and components. Please verify that none
of these parts are missing and/or damaged before
assembly. If any parts are missing/damaged please stop
assembly and contact ErgoMounts 01252 333326
Parts List
Swingout Arm (Qty 1)
Universal Mounting Brackets
(Qty 2)
Extension Adaptors (Qty 4)
5/16” x 3” Lag Bolts (Qty 6)
5/16” Flat Washers (Qty 6)
Griplate™ (Qty 6)
Thread Depth Indicator (Qty 1)
Universal Spacers (Qty 24)
Channel Covers (Qty 6)
M8 Nylon Nut (Qty 4)
5/16” Flat Washers (Qty 4)
Installation Tools
Phillips Screwdriver
1/4” Drill Bit
Electronic Stud Finder
Drill
Level
1/2” Socket and Socket Wrench
Tape Measure
M4 x 30mm (Qty 6)
M4 x 25mm (Qty 6)
M4 x 16mm (Qty 6)
M5 x 30mm (Qty 6)
M5 x 25mm (Qty 6)
M5 x 16mm (Qty 6)
M6 x 45mm (Qty 6)
M6 x 30mm (Qty 6)
M6 x 25mm (Qty 6)
M6 x 16mm (Qty 6)
M8 x 70mm (Qty 4)
M8 x 45mm (Qty 6)
M8 x 30mm (Qty 6)
M8 x 25mm (Qty 6)
M8 x 16mm (Qty 6)
2
Installation
The following steps must be performed by two
people.
Determine the desired viewing location. Use a stud
nder to locate two studs closest to the viewing
location.
Once the studs have been located, use a pencil to
mark the centre of each stud.
NB. A minimum of two (2) wall studs must be used in
the installation of this product.
When determining viewing height, the centre of
the TV should be at eye level while sitting in an
upright position. When using the at panel as room
decoration, raise it to the point where the bottom of
the screen is at eye level while sitting and the top is
eye level when standing.
Drill a pilot hole at the marked location using a
power drill and 1/4” drill bit.
NB. Only use 1/4” drill bit when drilling the pilot
holes.
Two people must perform the installation. One
person must hold the mount whilst the other person
levels the mount. The mount must remain in place
while the mounting hardware is tightened .
Level the mount.
Align the mounting slot with the drilled hole.
Insert and tighten one 5/16” x 3” lag bolt and at
washer. Tighten using a 1/2” socket wrench. Do not
completely tighten the lag bolt at this time.
NB. Do not overtighten lag bolts when attaching the
mount to the wall. Improper installation may result
in personal injury or damage to property.
1
2
3
Wood Stud Installation
1
2
3
Electronic Stud
Finder
Wall Stud
4
5
6
1/2” Socket Wrench
5/16” Lag Bolt
Flat Washer
Mounting Slot
Upper Mounting Channel
Wall Stud
1/4” Drill Bit
3
Installation
NB. Before drilling the second mounting hole, relevel the mount.
Drill a pilot hole at the marked location using a
power drill and a 1/4” drill bit.
Align the mounting slot with the drilled hole.
Insert and tighten one 5/16” x 3” lag bolt and at
washer. Tighten using a 1/2” socket wrench. Do not
completely tighten the lag bolt at this time.
Re-level the EMPRO-WM175B.
Using a 1/2” socket wrench completely tighten the two
upper lag bolts.
DO NOT over-tighten lag bolts when attaching the
mount to the wall. Improper installation may result in
personal injusry or damage to property.
NB. A minimum of two wall studs must be used in the
installation of this product.
Repeat these steps to secure the lower mounting
channel to the wall.
NB. There will be a total of four mounting points (2
for the upper mounting channel and 2 for the lower
mounting channel).
If the studs are 12” apart, use three 3” lag bolts for the
upper mouting channel and three 3” lag bolts for the
lower mounting channel. If the studs are 16”, 18” or
24” apart, use two 3” lag bolts for the upper mounting
channel and two 3” lag bolts for the lower mounting
channel.
137
9
Mounting slot
Flat Washer
Upper Mounting Channel
5/16” Lag Bolt
1/2” Socket Wrench
17
38
10
11
4
Loading...