Ergear EGSS2 Users guide

Monitor Desk Mount

Instruction Manual

V2.0

Model: EGSS2

Thank you for choosing this Ergear product! At Ergear we strive to
provide you with the best quality products and services in the
industry. Should you have any issues, please don't hesitate to
contact at [e-mail] (US/CA/DE/UK/FR/IT/ES/AU)

IMPORTANT SAFETY INFORMATION

Please carefully read all instructions before attempting installation. If you do not
understand the instructions or have any concerns or questions, please contact our
customer service at [e-mail].
CAUTION: Avoid potential personal injuries and property damage!

• Do not use this product for any purpose that is not explicitly specified in this manual. Do
not exceed weight capacity. We are not liable for damage or injury caused by improper
mounting, incorrect assembly or inappropriate use.

• This product contains a high pressure gas spring, fire and percussion prohibited. Also it
is strictly prohibited to dismantle without professionals. Please return to the manufacturer

or hand over to professional agencies if the product is abandoned.

• The desk must be capable of supporting three times the weight of the total load (the
mount, the monitor and all accessories weight). Don't use the product on particle board.

Weight Restrictions

WARNING

6.6-26.4 lbs.
(3-12 kg)

Your monitor (including
accessories) CANNOT EXCEED

6.6-26.4lbs (3-12 kg)

DO NOT exceed the maximum weight indicated.
This mounting system is intended for use only with
the maximum weights indicated. Use with products
heavier than the maximum weights indicated may
result in failure of the mount and its accessories,
causing possible damage and or injury.

If your monitor weighs more, this mount is NOT
compatible.

Check the VESA Pattern of Your Monitor before You Begin the Installation

MAX:100

mm/4 in.

mm/4 in.

MAX:100

MAX:100

If your Monitor VESA is greater than 100x100 mm/4x4 in. or less than
VESA 75x75mm/3x3in., this mount is NOT compatible.

If this desk mount is NOT compatible, please contact customer service

at [e-mail] to find a compatible product.

mm/4 in.

75 mm ≈ 3 in.
100 mm ≈ 4 in.

Minimum VESA pattern:

75mm/3 in.(W)x75mm/3 in.(H)

01

Product Features

C-Clamp Mounting

Grommet Mounting

02

TENSION ADJUSTMENT SHOULD BE DONE ONLY
AFTER MOUNT INSTALLATION

Do not adjust tension without monitor.

1. Ensure monitor has been attached to the mount.

2. Read your monitor box or manual to find out monitor net weight.

3. Ensure the net weight of monitor (including accessories) is between

6.6~26.4 Ibs (3-12 kg).

Adjustment Sign

Clockwise to reduce

tension(carry less weight)

Warning!

Counter-clockwise to increase

tension(carry more weight)

03

Parts and Hardware Included

Arm ExtenderArm

01 X1 02 X1

Base

03 X1

Decorative Cover

04 X1

X

Y

C-Clamp

05 X1

Monitor Plate

06 X1

USB Cable

07 X1

D

Butterfly

Nut

Grommet

Bolt

1/8 in.

(3mm)

1. Install the Base

A. For Clamp Mounting

1

Detach the C-clamp entirely

Y

E

(4mm)

A

M4x12mm

Bolt (x4)

E G

5/32 in.

(4mm)

Allen Key

13/64 in.

(5mm)

B-1

M4x16mm

Bolt (x4)

F

Locking

Plate

H

Pressure

Plate

B-2

5mm

Spacer (x4)

M8x38mm

Bolt

C

M6x12mm

Bolt (4pcs)

φ16xφ8.2x1.5mm

Washer

A-1 Install the USB Cable and C Clamp to the
Base

Install the USB cable [07] to

2

the base [03], then secure part [Y]
to the base [03]

07

X

Warning:

Ensure bolts are
secured firmly.

Y

E

(4mm)

03

C

Connect part [X] to part [Y] according to the thickness of the desktop

3

Y

OR

X

04

X

Y

A-2 Secure the Base to the Desktop

1

B. For Grommet Mounting

1

07

H

E

5/32in.

(4mm)

2

B-1 Install USB Cable and the Grommet
Bolt to Base

2

03

Warning:

Ensure bolts are
secured firmly.

D

B-2 Secure the Base to Desktop Using Locking Plate and Butterfly Nut

1 2

Ensure bolts are

secured firmly

F

D

05

2. Install the Arms

1 2

02

03

M

3 4

01

M

3. Install the Monitor Plate

E

G

Do not over-tighten the set
screw [M] in order not to

affect the rotation of the arm.

13/64 in.

(5mm)

M

E

1/8 in.

(3mm)

M

E

1/8 in.

(3mm)

01

06

Attach the monitor plate [06] from the sides
of the top end of arm [01], then secure the
monitor plate using bolt and washer [G]

06

4. Attach Monitors to the Arms

4-1 Choose Proper Bolts 4-2 Install Monitors to the Arms

Flat back monitor

0.1-0.2in.(3-5mm) spacing left

1

100x100mm

75x75mm

A

Curved back monitor

100x100mm

75x75mm

75 mm ≈ 3 in.
100 mm ≈ 4 in.

B-2

B-1

5. Adjust Gas Spring Tension

Screwdriver

[Not Included]

The tension is preset at

8.8-11 LBS(4-5kg). After
hanging the monitor to
the mount, please release
the monitor slowly to
prevent it from falling
suddenly.

Be sure to keep the arm in
horizontal position during
adjustment. Or else, it would

be difficult to adjust the

mount or damage the mount.

1. If the monitor can stay at the desired height
by itself, no adjustment needed.

2. If the monitor rises up, press the arm to keep
it in horizontal position and then use the 13/64
in.(5mm) Alley key (E) to turn the bolt
clockwise(“-” direction) to reduce tension of
the arm only until the monitor can stay at the
desired height by itself.

3. If the monitor falls down, lift the arm to keep
it in horizontal position and then use the 13/64
in.(5mm) Alley key (E) to turn the bolt
counter-clockwise(“+” direction) to increase
tension of the arm only until the monitor can
stay at the desired height by itself.

07

E

13/64 in.

(5mm)

6. Rotation Restriction

E

13/64 in.

(5mm)

(1 rotation ≈ 1 lb)

Non-proper usage directions

Proper usage directions

08

7. Tilt Adjustment

4. Route Cables along the Arm

Adjust monitor to proper tilt angle, using Allen key (E) to tighten the bolt and fix tilt angle

8. Route Cables along the Arms

8-1 Route cables along the arm [01]

01

8-2 Route cables along the arm extender [02]

02

5

13/64 in.

E

(5mm）

31 2

6 4

b

Pull down the groove part along the
arm to detach the cover from the arm

Pinch the both sides of the top end of
the cover to make it attach to the arm

09

Attach the Decorative Cover to C-Clamp

Warm Tips: The decorative cover [04]
can only be used for the C-Clamp.

04

10

Ensure screws are

secured firmly.

Thank you again for

choosing this Ergear product!

All of us at Ergear do appreciate your product purchase. We hope that
you are as happy with your product as we are designing and
manufacturing it for you. We strive to provide you with the best quality
products and services in the industry. Should you have any issues,
please don't hesitate to contact us at
[e-mail] (US/CA/DE/UK/FR/IT/ES/AU)