Erbauer ERB609MSW Original Instructions Manual

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

ERB609MSW

Original Instructions

Patent Pending 1008829.2

Read instructions fully before operating this tool

(SKU NO 85091 - J1X-KZ9-210J)

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

Congratulations on your purchase of a quality power tool from Erbauer Ltd.
This product should give you reliable service for your peace of mind this power
tool does carry a 24-month guarantee, the terms of which are detailed below.

If this product develops a fault within the guarantee period contact your retailer.

Please retain this handbook in case you need to refer to safety, care or guarantee
information in the future.

GUARANTEE

This product carries an Erbauer Ltd guarantee of 24 months. If your

product develops a fault within this period, you should, in the rst instance contact
your retailer. If the fault occurs within the rst 24 months, you may return the goods

for a full refund or we will repair or replace the goods if you prefer. When repair
is not practical or identical goods are not available, alternative goods of similar

specication and quality will usually be provided but, failing this, you will be oered

a partial or full refund depending on the time period since purchase.

This guarantee specically excludes losses caused due to:

-Fair wear and tear

-Misuse or abuse

-Lack of routine maintenance

-Failure of consumable items (such as batteries)

-Accidental damage

-Cosmetic damage

-Failure to follow manufacturer’s guidelines

-Loss of use of the goods

-Repairs attempted by anyone, unless authorised by Erbauer Ltd.

This guarantee does not aect your statutory rights. This guarantee is only valid in the UK.

For further technical advice and spare parts, please contact your retailer quoting
your Erbauer model number.

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

SAFETY INSTRUCTIONS

WARNING! Read all instructions. Failure to follow all instructions listed below

may result in electric shock, re and/or serious injury.

SAVE THESE INSTRUCTIONS

The term “power tool” in the warning refers to your mains-operated (corded) power
tool or battery-operated (cordless) power tool.

1. Work area
a. Keep work area clean and well lit. Cluttered and dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the presence

of ammable liquids, gases or dust. Power tools create sparks which may ignite
the dust or fumes.

c. Keep children and bystanders away while operating a power tool.

Distractions can cause you to lose control.

2. Electrical safety
a. Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools.

Unmodied plugs and matching outlets will reduce risk of electric shock.

b. Avoid body contact with earthed or grounded surfaces such as pipes, radiators,
ranges and refrigerators. There is an increased risk of electric shock if your body is

earthed or grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.

d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

e. When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply. Use of an RCD reduces the risk

of electric shock.

3. Personal safety
a. Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use a power tool while you are tired or under the inuence of

drugs, alcohol or medication. A moment of inattention while operating power tools

may result in serious personal injury.
b. Use safety equipment. Always wear eye protection. Safety equipment such

as dust mask, non-skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.

c. Avoid accidental starting. Ensure the switch is in the off-position before
plugging in. Carrying power tools with your nger on the switch or plugging in

power tools that have the switch on invites accidents.

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

d. Remove any adjusting key or spanner before turning the power tool on. A spanner

or a key left attached to a rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at all times. This enables

better control of the power tool in unexpected situations.

f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing
and gloves away from moving parts. Loose clothes, jewellery or long hair can be

caught in moving parts.

g. If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of these devices can

reduce dust related hazards.

4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application.

The correct power tool will do the job better and safer at the rate for which it was

designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power
tool that cannot be controlled with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source before making any adjustments,
changing accessories, or storing power tools. Such preventive safety measures

reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tools
operation. If damaged, have the power tool repaired before use. Many accidents

are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc., in accordance with these
instructions and in the manner intended for the particular type of power tool, taking
into account the working conditions and the work to be performed. Use of the

power tool for operations dierent from intended could result in a hazardous situation.

5. Service

Have your power tool serviced by a qualied repair person using only identical

replacement parts.

This will ensure that the safety of the power tool is maintained.

HEALTH ADVICE

WARNING! When drilling, sanding, sawing or grinding, dust particles will be
produced. In some instances, depending on the materials you are working
with, this dust can be particularly harmful to you (e.g. lead from old gloss paint).You
are advised to consider the risks associated with the materials you are working with
and to reduce the risk of exposure. You should:

-Work in a well-ventilated area.

-Work with approved safety equipment, such as dust masks that are specially

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

Safety instructions for all saws

a. DANGER: Keep hands away from cutting area and the blade. Keep your second
hand on the handle, or motor housing. If both hands are holding the saw, they

cannot be cut by the blade.
b. Do not reach underneath the workpiece. The guard cannot protect you from the
blade below the workpiece.
c. Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth
of the blade teeth should be visible below the workpiece.

d. Never hold piece being cut in your hands or across your leg. Secure the
workpiece to a stable platform. It is important to support the work properly to

minimize body exposure, blade binding, or loss of control.

e. Hold power tool by insulated gripping surfaces when performing an operation
where the cutting tool may contact hidden wiring or its own cord. Contact with a “live”

wire will also make exposed metal parts of the power tool “live” and shock the operator.

f. When ripping always use a rip fence or straight edge guide. This improves the
accuracy of cut and reduces the chance of blade binding.

g. Always use blades with correct size and shape (diamond versus round) of
arbor holes. Blades that do not match the mounting hardware of the saw will run

eccentrically, causing loss of control.
h. Never use damaged or incorrect blade washers or bolt. The blade washers and bolt
were specially designed for your saw, for optimum performance and safety of operation.

Further safety instructions for all saws

Causes and operator prevention of kickback:

− kickback is a sudden reaction to a pinched, bound or misaligned saw blade, causing

an uncontrolled saw to lift up and out of the workpiece toward the operator;

− when the blade is pinched or bound tightly by the kerf closing down, the blade stalls

and the motor reaction drives the unit rapidly back toward the operator;

− if the blade becomes twisted or misaligned in the cut, the teeth at the back edge of

the blade can dig into the top surface of the wood causing the blade to climb out of

the kerf and jump back toward the operator.
Kickback is the result of saw misuse and/or incorrect operating procedures or

conditions and can be avoided by taking proper precautions as given below.

a. Maintain a rm grip with both hands on the saw and position your arms to resist

kickback forces. Position your body to either side of the blade, but not in line with
the blade. Kickback could cause the saw to jump backwards, but kickback forces can

be controlled by the operator, if proper precautions are taken.

b. When blade is binding, or when interrupting a cut for any reason, release the
trigger and hold the saw motionless in the material until the blade comes to a
complete stop. Never attempt to remove the saw from the work or pull the saw
backward while the blade is in motion or kickback may occur. Investigate and take

corrective actions to eliminate the cause of blade binding.

c. When restarting a saw in the workpiece, centre the saw blade in the kerf and
check that saw teeth are not engaged into the material. If saw blade is binding,

it may walk up or kickback from the workpiece as the saw is restarted.

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

d. Support large panels to minimise the risk of blade pinching and kickback. Large

panels tend to sag under their own weight. Supports must be placed under the panel
on both sides, near the line of cut and near the edge of the panel.
e. Do not use dull or damaged blades. Unsharpened or improperly set blades

produce narrow kerf causing excessive friction, blade binding and kickback.

f. Blade depth and bevel adjusting locking levers must be tight and secure before
making cut. If blade adjustment shifts while cutting, it may cause binding and kickback.
g. Use extra caution when making a “plunge cut” into existing walls or other blind
areas. The protruding blade may cut objects that can cause kickback.

Safety instructions for saws

a. Check the lower guard for proper closing before each use. Do not operate the
saw if the lower guard does not move freely and close instantly. Never clamp or
tie the lower guard into the open position. If saw is accidentally dropped, the lower

guard may be bent. Raise the lower guard with the retracting handle and make sure it
moves freely and does not touch the blade or any other part, in all angles and depths
of cut.

b. Check the operation of the lower guard spring. If the guard and the spring are not
operating properly, they must be serviced before use. The lower guard may operate

sluggishly due to damaged parts, gummy deposits, or a build-up of debris.

c. Lower guard may be retracted manually only for special cuts such as “plunge
cuts” and “compound cuts.” Raise the lower guard by retracting handle and as
soon as blade enters the material, the lower guard must be released. For all other

sawing, the lower guard should operate automatically.

d. Always observe that the lower guard is covering the blade before placing saw

down on bench or oor. An unprotected, coasting blade will cause the saw to walk
backwards, cutting whatever is in its path. Be aware of the time it takes for the blade
to stop after switch is released.

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

ADDITIONAL SAFETY INSTRUCTIONS FOR YOUR MITRE SAW

WARNING! Be sure to read and understand all instructions. Failure to

follow all instructions listed below may result in electric shock, re and/

or serious personal injury.

1. Know your power tool. Read operator’s manual carefully. Learn the applications
and limitations, as well as the specic potential hazards related to this tool.

2. Always wear safety glasses or eye shields when using this mitre saw. Everyday
eyeglasses have only impact-resistant lenses; they are not safety glasses.

3. Always protect your lungs. Wear a face mask or dust mask if the operation is dusty.
Always use dust extraction equipment to minimise dust.

4. Always protect your hearing. Wear hearing protection during extended periods
of operation.

5. Always inspect the tool cords periodically and if damaged have them repaired.
Always be aware of the cord location.

6. Always check for damaged parts. Before further use of the tool, a guard or
other part that is damaged should be carefully checked to determine if it will
operate properly and perform its intended function. Check for misalignment or
binding of moving parts, breakage of parts, and any other condition that may
affect the tool’s operation. A guard or other part that is damaged should be
properly repaired or replaced at a qualied service centre.

7. Do not abuse the cord. Never use the cord to carry the tools or pull the plug from
the outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace
damaged cords immediately. Damaged cords increase the risk of electric shock.

8. Always make sure that your extension cord is in good condition. When using
an extension cord be sure to use one that is heavy enough to carry the current
that your tool will draw. An undersized cord will cause a drop in line voltage,
resulting in loss of power and overheating.

9. Always inspect and remove all nails from lumber before sawing.

10. Do not use the tool while tired or under the inuence of drugs, alcohol or any

medication. Following this rule will reduce the risk of electric shock, re or serious
personal injury.

11. Save these instructions. Refer to them frequently and use them to instruct
others who may use this tool. If someone borrows this tool, make sure they have
these instructions also.

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

12. When the correct blade to cut the material has been tted, this saw is

recommended for cutting wood, non-ferrous metal and plastic only.

13. Do not use saw blades with High Speed Steel (HSS) or damaged or deformed
blades.

14. Replace the table insert when worn.

15. Use only saw blades recommended by the manufacturer and which have the
exact bore and diameter required for this machine.

16. Connect your mitre saw to a dust collecting device (I. D.Ø32mm) when sawing.

17. Select saw blades in relation to the material to be cut.

18. Check the maximum depth of cut.

19. When sawing long work pieces, always use extra support to provide better
support, and use clamps or other clamping devices.

20. The operator is adequately trained in the use, adjustment and operation and
operation of the machine.

21. Provide for adequate room lighting at your workplace or for adequate lighting
of the immediate work area.

22. When tted with laser no exchange with different type of laser is permitted.

Repairs shall only be carried out by the laser manufacturer or an authorised agent.

23. Refrain from removing any cut-offs or other parts of the workpiece from the
cutting area whilst the machine is running and the saw head is not the rest position.

24. Never stand on this tool. Serious injuries could occur when this tool tips over
or when coming in contact with the saw blade.

WARNING! the operation of any mitre saw can result in foreign objects being

thrown into your eyes, which can result in severe eye damage. Before
beginning power tool operation, always wear safety goggles or safety glasses with
side shield and a full face shield when needed.
WARNING! If any parts are missing, do not operate your mitre saw until the
missing parts are replaced. Failure to follow this rule could result in serious
personal injury.

Caution: Do not let familiarity with your mitre saw make you careless. Remember
that a careless fraction of a second is sucient to cause severe injury.

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

Double insulation:

The tool is double insulated. This means that all the external metal parts are

electrically insulated from the mains power supply. This is done by placing insulation
barriers between the electrical and mechanical components making it unnecessary
for the tool to be earthed.

Important note
Be sure the supply is the same as the voltage given on the rating plate. The tool is

tted with a two-core cable and plug. Remove the mains plug from socket before
carrying out any adjustment or servicing.

SPECIFIC SAFETY RULES & SYMBOLS

WARNING!

Do not operate machine if warning and / or instruction labels are missing or damaged.

Symbol Description

V Volts

A Amperes

Hz Hertz

Min

-1

Speed

~ Alternating Current

No No Load Speed

Double Insulated

Wear Safety Goggles

Wear Ear Protection

Wear Dust Mask

Read Instruction Manual

Laser Warning Symbol

Conforms to relevant

safety standards

General Warning

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

KNOW YOUR SLIDING MITRE SAW

Fig 1

1. DUST BAG

2. UPPER BLADE GUARD

3. CUTTING HANDLE

4. LOWER BLADE GUARD

5. BLADE

6. TABLE INSERT

7. MITRE HANDLE

8. BEVEL LOCK HANDLE

9. BASE

10. TURNTABLE

11. LEFT EXTENSION TABLE

12. FENCE

13. HOLD-DOWN CLAMP

14. SLIDE CARRIAGE LOCK KNOB

6

1

3

12

10

14

2

4

7

8

9

11

5

13

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

15. CARRYING HANDLE

16. SLIDE CARRIAGE

17. LASER GUIDE

18. RIGHT EXTENSION TABLE

19. MOTOR

20. POSITIVE STOP LOCKING LEVER

21. LOWER BLADE GUARD LOCK LEVER

22. LASER ON/OFF SWITCH

23. ADJUSTABLE CUTTING STOP

Fig 2

17

15

18

20

21

22

23

16

19

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

TECHNICAL DATA

Volts: 230V~50Hz

Power input: 1400W

No-load speed: 4500min-1

Double insulation: Class 2

Net weight: 14.05kg

Blade: Ø210 mm ; Ø30 mm Bore

Minimum Blade thickness 1.8mm Kerf 3.0mm

Turntable Ø295 mm

Mitre stops 0°,15°, 22.5°, 31.6°, 45° Left & Right

Mitre angle range 45° Left & Right

Bevel angle range 0° to 45° Left

Maximum capacity

Cross cut (0° Bevel x 0° Table) 63mm x 233mm

Mitre cut (0° Bevel x 45° Table) 63mm x 117m

Bevel cut (45° Bevel x 0° Table) 46mm x 233mm

Compound cut (45° Bevel x 45° Table) 46mm x 117mm

NOISE AND VIBRATION DATA

Sound pressure level LPA: 94 dB(A) (K=3dB(A))

Sound power level LWA: 107 dB(A) (K=3dB(A))

Vibration level: 3.384m/s2 (K=2.5m/s2)

- The declared vibration total value has been measured in accordance with a
standard test method and may be used for comparing one tool with another.

- The declared vibration total value may also be used in a preliminary assessment of

exposure.

WARNING! The vibration emission during actual use of the power tool can dier

from the declared total value depending on the ways in which the tool is used; and
of the need to identify safety measures to protect the operator that are based on an

estimation of exposure in the actual conditions of use (taking account of all parts of
the operating cycle such as the times when the tool is switched o and when it is

running idle in addition to the trigger time).

ACCESSORIES

Allen Key 1 pc, Dust Bag 1 pc, Hold-Down Clamp 1 pc & Mitre Handle 1 pc

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

VIBRATION

The European Physical Agents (Vibration) Directive has been brought in to help

reduce hand arm vibration syndrome injuries to power tool users. The directive

requires power tool manufacturers and suppliers to provide indicative vibration test

results to enable users to make informed decisions as to the period of time a power

tool can be used safely on a daily basis and the choice of tool.Further Advice can be

found at www.hse.gov.uk

Vibration total values (triax vector sum) determined according to EN 61029

Test specication; Standard = EN61029-1 2009.
Test prodcure GS mark.

Vibration emission value ah = 3.384m/s²

Uncertainty K = 2.5m/s²

The declared vibration emission value should be used as a minimum level should be used with
the current guidance on vibration.

Calculating the actual period of the actual period o use can be dicult and the HSE website

has further information.

The declared vibration emission been measured in accordance with a standardised test stated
above and may be used to compare one tool with another.

The declared vibration emission value may also be used in a preliminary assessment of exposure.
WARNING! The vibration emission value during actual use of the power tool can dier

from the declared value depending on the ways in which the tool is used

dependant on the following examples and other variations on how the tool is used:-

How the tool is used and the materials being cut or drilled.
The tool being in good condition and well maintained
The use the correct accessory for the tool and ensuring it is sharp and in good condition.
And the tool is being used as intended by its design and these instructions.

This tool may cause hand-arm vibration syndrome
if its use is not adequately managed

WARNING! identify safety measures to protect the operator that are based on an

estimation of exposure in the actual conditions of use (taking account of all parts
of the operating cycle such as the times when the tool is switched o and when it is

running idle in addition to the trigger time).Note The use of other tools will reduce the

users’ total working period on this tool. Helping to minimise your vibration exposure risk.

ALWAYS use sharp chisels, drills and blades. Maintain this tool in accordance with these
instructions and keep well lubricated (where appropriate)
Avoid using tools in temperatures of 10C or less
Plan your work schedule to spread any high vibration tool use across a number of days.

Health Surveillance

All employees should be part of an employer’s health surveillance scheme to help identity
any vibration related diseases at an early stage, prevent disease progression and
help employees stay in work.

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

ASSEMBLY INSTRUCTIONS

WARNING! To avoid injury, do not connect

this mitre saw to the power source until it is

completely assembled and adjusted and you have

read and understood this Operator’s Manual.

1. Installing the mitre handle

1) Thread the mitre handle (1) into the hole

located at the front of the mitre table. (See g. 3)

2. Unlocking the slide carriage

After removing the saw from the carton,
loosen the slide carriage lock knob (1). When
transporting or storing the mitre saw, the slide
carriage should always be locked in position.
The slide carriage lock knob (1) is located on the

side of the slide carriage. (See g. 4)

3. Raising the Cutting Head

1) Push down slightly on the switch handle (1)
and the lock lever (2).

2) Pull out the stop latch knob (3).

3) Allow the cutting head to rise to the up
position. (See g. 5)

WARNING! To avoid injury and damage

to the saw, transport and store the
mitre saw with the cutting head locked in the
down position. Never use the stop latch to hold
the cutting head in a down position for cutting
operations.

Locking

When transporting or storing the mitre saw,
the cutting head should always be locked in
the down position.

1) Push the lock lever (2) and cutting head down
to its lowest position.

2) Push the stop latch knob (3) into the locking hole.

IMPORTANT

To avoid damage, never carry the mitre saw by
the cutting arm or the mitre handle. ALWAYS use
both designated carrying handles together.

Fig 5

1

2

3

Fig 4

1

Fig 3

1

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

4. Installing the dust bag

1) Squeeze the metal collar wings (2) of the

dust bag (1).

2) Place the dust bag neck opening around the

exhaust port (3), and release the metal collar
wings. (See g. 6)

5. Installing the hold-down clamp

1) Loosen the lock knob (1) from the rear side

of the saw base (2). (See g. 7)

2) Place the hold-down clamp assembly (3) in
one of the mounting holes (4). (See g. 8)

3) Tighten the lock knob (1). (See g. 7)

WARNING! Always check clamp
position does not interfere with any
saw operation. Before switching on, lower the
saw head to ensure the clamp clears the guard
and saw head assembly.

Fig 6

1

3

2

Fig 8

4 4

Fig 7

3

2

1

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

6. Mounting the mitre saw

WARNING! To avoid injury from

unexpected saw movement:

• Disconnect the power cord from the outlet,

and lock the cutting head in the lower position
using the stop latch.

• Lock the slide carriage in place by tightening

the slide carriage lock knob.

• To avoid back injury, lift the saw by using the

designated carrying handles located on the
top of the machine. When lifting, bend at your
knees, not from your back.

• Never carry the mitre saw by the power cord

or by the switch handle. Carrying the tool by
the power cord could cause damage to the
insulation or the wire connections resulting in

electric shock or re.

• To avoid injury from ying debris, do not allow

visitors to stand near the saw during any cutting
operation.

• Support the saw on a level work surface.

• Bolt or clamp the saw to its support.

Mounting instructions

1) For stationary use, place the saw in the
desired location, directly on a workbench where
there is room for handling and proper support
of the workpiece. The base of the saw has four
mounting holes. Bolt the base of the mitre saw
(1) to the work surface (5),using the fastening
method as shown in Fig 9.

2) For portable use, place the saw on a

20mm(approx) thick piece of plywood. Bolt the

base of the mitre saw securely to the plywood
using the mounting holes on the base. Use
G-clamps to clamp this mounting board to a

stable work surface at the worksite. (See g. 10)

Note: Mounting hardware is not included with
this tool. Bolts, nuts, washers and screws must
be purchased separately.

Fig 9

Fig 10

1) Hex headed bolt

2) Flat washer

3) Rubber washer

4) Mitre saw base

5) Workbench

6) Flat washer

7) Lock washer

8) Hex nut

9) Lock nut

1

2

3

4

5

6

7

8

9

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

7. Removing and installing the blade

WARNING!

• Do not use a blade larger than 210mm in

diameter or less than 1.8mm thick.

• To avoid injury from an accidental start, make

sure the switch is in the OFF position and the
plug is not connected to the power source outlet.

• For clarity the operators hands are shown
in gs13 and 14. We recommend that the

operator considers wearing protective gloves
when handling or installing the blade.

Removing blade

1) Unplug the saw from the outlet.

2) The slide carriage should be locked in
position by tightening the slide carriage lock

knob (1). (See g. 11)

3) Allow the cutting head to rise to the upright
position. (See g. 11)

4) Release the lower blade guard by operating
the blade guard handle, and rotate the guard
into its upper position.

5) Locate the arbor lock (1). (See g. 12)

6) Hold the guard in position with your thumb
and press the arbor lock gently with a nger.
(See g. 13)Rotate the blade using the correct
sized hex key inserted into the arbor bolt (See
g. 14) until positive location is felt.

7) Keeping the arbor lock rmly pressed undo
the arbor bolt with the hex key by turning it in a

clockwise direction.

8) Remove the bolt and outer blade collar from
the machine.

9) With the arbor bolt and out blade collar
removed, gently ease the blade from the arbor
and remove downwards and away from the
cutting head.
Note: Pay attention to the pieces removed,
noting their position and direction they face.
Wipe the blade collars clean of any sawdust
before installing a new blade.

Fig 11

Fig 12

Fig 13

Fig 14

1

1

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

8. Installing Blade

Unplug the mitre saw before changing/installing

the blade.

Note: Ensure that the saw blade bore is exactly

the correct size for this machine and the

diameter does not exceed 210 mm.

1) Rotate and hold lower blade guard in its
upper position as already described.

2) Install a 210 mm blade with 30 mm arbor,

making sure the rotation arrow on the blade
matches the clockwise rotation arrow on the
upper guard and the blade teeth are pointing
downward.

3) Place the outer blade collar against the blade

and on the arbor. Thread the arbor bolt onto the

arbor in a counterclockwise direction. (See g. 15)

IMPORTANT

Make sure the ats of the blade collars are
engaged with the ats on the arbor shaft.

4) Place the hex key into the arbor bolt.

5) Press the arbor lock, holding gently while
turning the blade counterclockwise. When arbor

lock engages, continue to press it in rmly while
tightening the arbor bolt securely. (See g. 14)

Note: Do not press arbor lock when blade
is moving.

WARNING! Be sure that the arbor lock
is released so that the blade turns
freely. Lower the blade into the lower table and
check for any contact with the base or the mitre
table by spinning the blade manually. Make sure
the collars are clean and properly arranged.
Check that the lower blade guard is functioning
correctly and does not bind or stick.

Fig 15

Blade

Inner
Blade
Collar

Outer
Blade
Collar

Arbor
Bolt

Spacer

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

9. Aligning the laser beam

WARNING! For your own safety,

never connect the plug to power

source outlet until all the adjustment steps

are complete and you have read and
understood the safety and operational
instructions. The laser beam must always
be correctly aligned with the blade to
ensure straight, even cutting.

Your tool is equipped with the Laser guide

cutting guide using a Class II laser beam.
The laser beam will enable the operator to
preview the saw blade path on the stock
to be cut before starting the saw. This
laser guide is powered by the transformed
alternating current supply directly through the
power lead. The saw must be connected to

the power source and the laser on/o switch

must be turned on for the laser line to show.

(See g.16)

WARNING!
AVOID DIRECT EYE CONTACT
Laser radiated when laser guide is turned
on. Avoid direct eye contact. Always unplug
the mitre saw from power source before

making any adjustments.
Laser Warning Label: Max output <1mW
Wavelength: 630-670nm EN 60825-1/
A1:2007. Laser radiation do not stare into

beam Class 2 Laser Product Puissance.

Note: All the adjustments for the operation

of this machine have been completed at the
factory. Due to normal wear and use, some

occasional readjustments may be necessary.

A. Check Laser Beam Alignment

1) Mark a 90° straight line across a board
to serve as a “pattern line” to test laser
alignment. Lay the board on the mitre table.

2) Plug saw into outlet and turn on the laser
beam and line it up with the pattern line.

3) Lower saw blade to pattern line and
if blade is not ush with the pattern line,
adjustment may be necessary.

Fig 16

Laser ON/OFF Switch

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

Three laser module mounting/adjustment

screws are provided. Two (1,2) are positioned
on the LH side of the laser housing, and one

(3) on the RH side of the laser housing. These

screws gently hold the laser module in place
and on alignment by bearing on the laser
modules casing. It is important that during any

adjustment the pressure on the laser module

casing is maintained as closely as possible
to the factory setting. Do not over tighten any
one screw – damage to the laser casing could

result. (See g. 17&18)

B Adjusting the Angle of the Laser Guide

1) Loosen the single screw on the RH side of
the laser housing ½ a turn.

2)Turn the laser element in the desired direction

to adjust the laser angle.

3)Retighten the adjustment screw.

C Aligning the Laser Beam

1)Use the two adjusting screws on the LH side

of the laser housing.

2)Adjust both screws until laser alignment is

achieved.

WARNING! Use only the correct sized

hex key when adjusting these screws.

Turn one screw at a time and only ¼ turn in
either direction before checking laser alignment.
Maintain as far as possible the original factory

pressure setting that these screws exert on the

laser module.

Fig 18

Fig 17

1

3

2

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

ADJUSTMENT INSTRUCTIONS

1. Bevel stop adjustment
WARNING! To avoid injury from an

accidental start, make sure the
switch is in the OFF position and the plug is not
connected to the power source outlet.

2. 90° (0°) Bevel adjustment

1) Loosen bevel lock handle (1) and rotate the
cutting arm completely to the right until it stops
against the vertical stop. Tighten the bevel lock
handle.

2) Place a combination square (2) on the mitre

table with the ruler against the table and the

heel of the square against the saw blade.

3) If the blade is not 90° (0°) square with the mitre

table (5), loosen the bevel lock handle (1), tilt the
cutting head to the left, loosen the locknut (4) on the

bevel angle adjustment bolt (3) and use an hex key
to adjust the socket headed stop bolt (3) depth in or

out to increase or decrease the bevel angle.

4) Tilt the cutting arm to back to the right at 90°
(0°) bevel and recheck for alignment.

5) Repeat steps 1 through 4 if further adjustment

is needed.

6) Tighten bevel lock handle (1) and locknut (4)

when alignment is achieved. (See g. 19)

Fig 19

2

5

4

3

1

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

3. Bevel pointer adjustment

1) When the blade is exactly 90° (0°) to the
table, loosen the bevel indicator screw (1) using
a # 2 Phillips screwdriver.

2) Adjust bevel indicator (2) to the “0°” mark on
the bevel scale and retighten the screw.

(See g. 20)

4. Bevel adjustment 45°

1) Loosen the bevel lock handle (1) and tilt the
cutting head completely to the left.

2) Using a combination square, check to see if

the blade angle is 45° to the table.

3) If the blade is not at 45° to the mitre table, tilt
the cutting arm to the right, loosen the locknut

(2) on the bevel angle adjustment bolt (3) and
use an hex key to adjust the stop bolt (3) depth

in or out to increase or decrease the bevel angle.

4) Tilt the cutting arm to the left to 45° bevel
and recheck for alignment.

5) Repeat steps 1 through 4 until the blade is at
45° to the mitre table.

6) Tighten bevel lock handle (1) and locknut (2)
when alignment is achieved. (See g. 21)

5. Bevel Setting for Crown Moulding
The cutting arm can also be set at 33.9°

for

cutting crown mouldings.

1) Twist and deploy sprung-loaded crown
moulding pin (2).

2) Loosen the bevel lock handle (1) and rotate

the cutting head in the required direction until
it indexes with the moulding pin (2). Tighten the
bevel lock. (See g. 22)

Fig 20

Fig 21

Fig 22

1

2

1

2

3

2

3

1

2

3

4

3

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

6. Bevel adjustment 33.9

o

If necessary the 33.9° settings can be checked
and adjusted. A vernier angle gauge will be
required and this must be accurately set to 33.9°

1) Set the cutting head to 33.9° by deploying

the crown moulding pin. Check the angle of
the blade against the machine table using the

vernier angle gauge. (See g. 23)

2) If adjustment is required loosen the locknut (3)
to the relevant socket headed stop screw. Adjust

the screw in or out until the correct bevel angle
is achieved. Retighten the locknut. (See g. 22)

7. Mitre angle adjustment

The sliding compound mitre saw scale can be
easily read, showing mitre angles from 0° to
45° to the left, and 0° to 45° to the right. The
mitre saw table has nine of the most common
angle settings with positive stops at 0°, 15°,

22.5°, 31.6°, and 45°. These positive stops
position the blade at the desired angle quickly

and accurately. Follow the process below for

quickest and most accurate adjustments.

1) Unlock the mitre table by turning the mitre
handle (1) counterclockwise.

2) Move the turntable while lifting up on
the positive stop locking lever (2) to align

the indicator (3) to the desired degree

measurement.

3) If the desired angle is one of the nine positive

stops, release the positive stop locking lever,
making sure the lever snaps into position, and
then secure by tightening the mitre handle.

4) If the mitre angle desired is not one of the
nine positive stops, simply lock the mitre table
into position by turning the mitre handle in the

clockwise direction. (See g. 24)

8. Mitre scale indicator adjustment

1) Move the table to the 0° positive stop.

2) Loosen the screw (4) that holds the indicator
with a Phillips screwdriver.

3) Adjust the indicator (3) to the 0° mark and
retighten screw. (See g. 24)

Fig 24

Fig 23

1

2

4

3

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

9. Adjusting fence squareness

1) Loosen the four fence locking bolts (1).

2) Lower the cutting arm and lock in position.

3) Using a square (3), lay the heel of the square

against the blade and the ruler against the
fence(2) as shown.

4) Adjust the fence 90° to the blade and tighten
the four fence locking bolts. (See g. 26)

Caution: If the saw has not been used recently,

recheck blade squareness to the fence and
readjust if needed.

5) After fence has been aligned, using a scrap piece

of wood, make a cut and check ‘squareness’ of
the cut in the piece. Readjust if necessary.

10. Setting cutting depth

The depth of cut can be preset for even and
repetitive shallow cuts.

1) Adjust the cutting head down (See CUTTING

HEAD section) until the teeth of the blade are at
the desired depth.

2) While holding the upper arm in that position,
turn the stop knob (1) until it touches the stop
plate (2).

3) Recheck the blade depth by moving the

cutting head front to back through the full
motion of a typical cut along the control arm.

(See g. 26)

11. Adjusting cutting depth

The maximum depth travel of the cutting head

was set at the factory. Check to see that the

blade does not extend more than 6.35 mm below

the table insert, and does not touch the control
arm throat or any part of the base or table. If the

maximum depth needs readjusting:

1) Loosen the depth control screw locknut (3).

2) Pull the cutting head down until it indexes with

the depth control screw.

3) Adjust the depth control screw until the blade
extends 6.35mm below the table insert.

4) Recheck the blade depth by moving the
cutting head front to back through the full
motion of a cut along the control arm. If the
blade touches the inside of the control arm,

readjust the setting. Tighten the locknut when
the correct setting is achieved.(See g. 26)

Fig 25

Fig 26

1

3

2

1

2

3

1

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

OPERATION INSTRUCTIONS

WARNING! Before using your mitre
saw be sure to read the instruction
manual carefully.

Operating instructions

1. Know your mitre saw

Read and understand the Operator’s Manual

and labels axed to the tool. Learn its

application and limitations as well as the

potential hazards specic to this tool. To avoid
injury from accidental contact with moving

parts, do not lay out, assemble or set up work
on the mitre saw.

2. Electrical connection

Your mitre saw has a precision-built electric
motor and it should only be connected to a
240 V. 50Hz. Power supply (normal household
current). Do not operate on direct current
(DC). This large voltage drop will cause a loss
of power that will overheat the motor. If your
mitre saw does not operate when plugged
into an outlet, have a professional electrician
check the power supply.
WARNING! Avoid accidental starting.
Make sure the switch is in the OFF
position before plugging the mitre saw into a
power outlet.

3. Body and Hand position
WARNING! Never place hands near the

cutting area. Proper positioning of your
body and hands when operating the mitre saw
will make cutting easier and safer. Keep children
away. Keep all visitors at a safe distance from the
mitre saw. Make sure bystanders are clear of the
saw and workpiece. Don’t force the saw. It will

do the job better and safer at its designed rate.

Starting a cut:

• Place hands at least 190.5 mm away from

the blade – out of the “no-hands zone” (1).

(See Fig 27)

• Clamp workpiece rmly against the fence to

prevent movement toward the blade.

• With the power switch OFF, bring the saw

Fig 27

No-Hands Zone

1

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

blade down to the workpiece to see the cutting
path of the blade

• Squeeze trigger switch to start saw.

• Lower blade into workpiece with a rm

downward motion.

Finishing a cut:

• Hold the cutting arm in the down position.

• Release trigger switch and wait for all moving

parts to stop before moving your hands and
raising the cutting arm.

Before releasing jammed material:

• Release trigger switch.

• Wait for all moving parts to stop.

• Unplug the mitre saw.

4. Basic saw operations
Warning! For your convenience, your

saw has a blade brake. The brake is not
a safety device. Never rely on it to replace the
proper use of the guard on your saw. If the blade

doesn’t stop within approximately 8 seconds,

wait for the blade to stop, unplug the saw and
contact customer service.
To turn saw on

Push down the lock lever (1) and squeeze the

trigger switch (2) to turn the mitre saw ON.
Release the trigger switch to turn the saw OFF.

(See g. 28)

5. Sliding carriage system

1) For chop cutting operations on small
workpieces, slide the cutting head assembly
completely toward the rear of the unit and
tighten the carriage lock knob (1).

2) To cut wide boards up to 233 mm, the

carriage lock knob must be loosened to allow

the cutting head to slide freely. (See g. 29)

Before leaving the saw

• Never leave tool running unattended. Turn

power OFF. Wait for all moving parts to stop.

• Make workshop childproof. Lock the shop.

Disconnect master switches. Store tool away

from children and other unqualied users.

Fig 28

Fig 29

1

1

2

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

WARNING! To avoid injury from

materials being thrown, always
unplug the saw to avoid accidental starting,
and remove small pieces of material from the
table cavity.

6. Mitre cut

1) When a mitre cut is required, unlock the

mitre table by turning the mitre handle (1)
counterclockwise.

2) While holding the mitre handle, lift up on the
positive stop locking lever (2).

3) Rotate the mitre table to the right or left

with the mitre handle.

4) When the table is in the desired position,

as shown on the mitre scale (3), release the

positive stop locking lever and tighten the
mitre handle. The table is now locked at the
desired angle. Positive stops are provided at

0°, 15°, 22.5°, 31.6° and 45°. (See g. 30)

IMPORTANT

Always tighten the mitre table lock handle
before performing every cutting operation.

7. Bevel cut

1) When a bevel cut is required, loosen the

bevel lock handle (1) by turning it clockwise.

2) Tilt the cutting head to the desired angle,
as shown on the bevel scale (2)

3) The blade can be positioned at any angle,

from a 90° straight cut (0° on the scale) to a
45° left bevel. Tighten the bevel lock handle
(1) to lock the cutting head in position.
Positive stops are provided at 0°, 33.9° and
45°. (See g. 31)
Note: When cutting at 45 degrees, ensure
guard does not catch on work or machine
base plate.

Fig 30

Fig 31

3

1

2

1

2

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

8. Compound cut

A compound cut is the combination of a mitre
and a bevel cut simultaneously.

1) Loosen the bevel lock handle (1) and position
the cutting head at the desired bevel position.
Lock the bevel lock handle.

2) Loosen the mitre handle (2). Press down the

positive stop locking lever (3) and position the

table at the desired angle. Release the positive
stop locking lever and lock the mitre handle.

(See g. 32)

IMPORTANT

When cutting a maximum RH or LH compound
cut (mitre at 45˚ bevel at 45˚) move the RH
or LH fence extension by rst loosening the

locking screw (A) and secondly pulling the

locking pin (B) and sliding the extension away
from the cutting area (C). (See g. 32)

9. Slide cutting wide boards up to 233 mm wide

WARNING!
To avoid injury:

• Never pull the cutting head assembly and

spinning blade toward you during the cut. The
blade may try to climb up on the top of the
workpiece, causing the cutting assembly and
spinning blade to kick back, forcefully. The
cutting head assembly should be drawn back
completely then pushed forward when sawing.

• Let the blade reach full speed before cutting.

This will help reduce the risk of a thrown
workpiece.

To slide cut wide boards

1) Unlock the carriage lock handle (1) and allow
the cutting head assembly to move freely.

2) Set both the desired bevel angle and/or the

mitre angle and lock into position.

3) Use a hold down clamp to secure the

workpiece.

4) Grasp the switch handle (2) and pull the

carriage (3) forward until the centre of the saw

blade is over the front of the workpiece (4).

5) Engage the trigger to turn the saw on.

Fig 32

1

2

3

B

A

C

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

6) When the saw reaches full speed, push the

switch handle down, slowly, cutting through
the leading edge of the workpiece.

7) Slowly move the switch handle toward the

fence, completing the cut.

8) Release the trigger and allow the blade to
stop spinning before allowing the cutting head

to raise to its upper position. (See g. 33)

10. Cutting bowed material

A bowed workpiece must be positioned
against the fence and secured with a clamping
devise before cutting as shown.

WARNING! Do not position workpiece
incorrectly or try to cut the workpiece

without the support of the fence. (See g. 34)

This will cause the blade to bind and could

result in personal injury.

11. Satellite workpiece support

Incorporated into the LH side of the machine
base is a removable satellite stand. Use this
stand to help support long pieces of material.
To remove the satellite stand, press the release
button on the top, and slide the stand from the
machine base. Position where convenient to

adequately support long workpieces.

To replace, simply slide the satellite stand back
into the machine base until the release button

provides positive location. (See g. 35)

Fig 34

Fig 35

Fig 33

1

3

4

2

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

12. Adjustable stop plate

A stop plate designed for use during repetitive

cutting is incorporated into the extension arm

on the RH side of the machine base. The stop
plate can be deployed in two positions, inboard
and outboard.
The inboard position enables repetitive cuts of
shorter lengths by positioning the stop plate
close to the blade. The outboard position is
used for the repetitive cutting of longer lengths

by positioning the stop at its maximum distance

from the blade.

To deploy the stop:

1) Slide the release lock forwards.

2) Pull the stop(1) from its stored position
upwards and to the left. The stop will deploy.

3) Slide the release lock (2) backwards to lock

the stop into position.

4) To stow away, reverse the above steps. (See

g. 36)

To deploy the stop outboard:

1) Slide the sprung-loaded lock (2) forwards.

2) Whilst holding the release lock, pull the stop (1)
from its stored position upwards and to the right.
The stop will deploy to the outboard position.

3) Slide the release lock (2) backwards to lock

the stop position.

4) To stow away, reverse the above steps. (See

g. 37)

Adjusting the stop plate

Deploy the stop plate as outlined above.

1) Push the release button (1) on the front of the
machine base below the stop plate.

2) Slide the extension arm (2) from the machine

base, and release the button (1) when at the

approximate required distance.
The extension arm has a micro adjustment
facility for nal positioning.
Turn the adjustment knob (3) clockwise or
counter clockwise as required for nal exact
positioning of the stop plate. (See g. 38)

13. Extension Arm

With the stop plate in its stored position the

extension arm can be used to support long
workpieces. (See g. 38)

Fig 38

1

2

3

Fig 37

1

2

Fig 36

1

2

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

14. Cutting base moulding

Base mouldings and many other mouldings can
be cut on a compound mitre saw. The setup of
the saw depends on moulding characteristics
and applications, as shown. Perform practice

cuts on scrap material. To achieve best results:

1) Always make sure mouldings rest rmly

against fence and table. Use hold-down or
G-clamps, whenever possible, and place tape
on the area being clamped to avoid marks.

2) Reduce splintering by taping the cut area prior
to making cut. Mark cut line directly on the tape.

3) Splintering typically happens due to wrong

blade application and thinness of the material.
Note: Always perform a dry run cut so you can
determine if the operation being attempted is
possible before power is applied to the saw.

15. Cutting crown moulding

Your compound mitre saw is suited for the dicult
task of cutting crown moulding. To t properly,

crown moulding must be compound mitred with

extreme accuracy. The two surfaces on a piece
of crown moulding that t at against the ceiling

and wall are at angles that, when added together,
equal exactly 90°. (See g. 39&40)

Most crown moulding has a top rear angle (the

section that ts at against the ceiling) of 52°
and a bottom rear angle (the section that ts at
against the wall) of 38°.

In order to accurately cut crown moulding for a 90°
inside or outside corner, lay the moulding with its

broad back surface at on the saw table.

When setting the bevel and mitre angles for
compound mitres, remember that the settings
are interdependent – changing one changes the

other, as well. (See g. 41&42)

Fig 39

Fig 40

Fig 41

F
e
n
c
e

Mitre at 45o, bevel at 0

o

F
e
n
c
e

Mitre saw table

F
e
n
c
e

Mitre saw table

Mitre saw table

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

Bevel/Mitre Settings

Settings for standard crown moulding lying

at on compound mitre saw table

Note: The chart below references a
compound cut for crown moulding ONLY
WHEN THE ANGLE BETWEEN THE WALLS
EQUALS 90

o

.

KEY BEVEL

SETTING

MITRE

SETTING

TYPE OF CUT

Inside Corner-Left side

IL 33.9

0

31.60 Right

1)Position top of moulding against fence

2)Mitre table set at Right 31.6

0

3)Left side is nished piece

Inside Corner-Right side

IR 33.9

0

31.60 Left

1)Position bottom of moulding against
fence.

2)Mitre table set LEFT 31.6

0

Outside Corner-Left side

OL 33.9

0

31.60 Left

1)Position bottom of moulding against
fence.

2)Mitre table set at Left 31.6

0

3)RIGHT side is nished piece.

Outside Corner-Right side

OR 33.9

0

31.60 Right

1)Position top of moulding against fence.

2)Mitre table set at RIGHT 31.6

0

3)RIGHT side is nished piece.

Fig 42

IL

IR

OL

OR

Inside Corner

Outside Corner

Compound Cut Crown Mouldings

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

MAINTENANCE

Danger: To avoid injury, never put

lubricants on the blade while it
is spinning.

WARNING! To avoid re or toxic

reaction, never use petrol, naphtha,

acetone, lacquer thinner or similar highly

volatile solvents to clean the mitre saw.
WARNING! For your safety, this saw
is double-insulated. To avoid

electrical shock, re or injury, use only parts
identical to those identied in the parts list.
Reassemble exactly as the original assembly

to avoid electrical shock.

Replacing carbon brushes

Replace both carbon brushes when either has

less than 6 mm length of carbon remaining,

or if the spring or wire is damaged or burned.

To inspect or replace brushes, rst unplug

the saw. Then remove the black plastic cap
(1) on the side of the motor (2). Remove the
cap cautiously, because it is spring loaded.
Then pull out the brush and replace. Replace
for the other side. To reassemble reverse the
procedure. The ears on the metal end of the
assembly go in the same hole the carbon part

ts into. Tighten the cap snugly, but do not
overtighten. (See g. 43)
Note: To reinstall the same brushes, rst

make sure the brushes go back in the way
they came out. This will avoid serviceable
brushes undergoing a second ‘bedding
in’ process that could reduce motor
performance and increases wear.

Lower blade guard

Do not use the saw without the lower blade
guard. The lower blade guard is attached to
the saw for your protection. Should the lower
guard become damaged, do not use the saw
until the damaged guard has been replaced.
Develop a regular check to make sure the
lower guard is working properly. Clean the
lower guard of any dust or buildup with a
damp cloth.

Fig 43

1

2

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

WARNING! Do not use solvents on the

guard. They could make the plastic
“cloudy” and brittle.

WARNING! When cleaning the lower
guard, unplug the saw from the power

source to avoid unexpected startup.

Sawdust
Periodically, sawdust will accumulate under the work

table and base. This could cause diculty in the

movement of the worktable when setting up a mitre

cut. Frequently blow out or vacuum up the sawdust.

WARNING! If blowing sawdust, wear
proper eye protection to keep debris
from blowing into eyes.

Lubrication
All the motor bearings in this tool are lubricated

with a sucient amount of high grade lubricant

for the life of the unit under normal operating
conditions; therefore, no further bearing

lubrication is required. Lubricate the following as
necessary: Chop pivot: Apply light machine oil.
Central pivot of plastic guard: Use light household

oil (sewing machine oil ) on metal-to-metal or

metal-to-plastic guard contact areas as required
for smooth, quiet operation. Avoid excessive oil,
to which sawdust will cling. Guard arm: (which

actuates the lower guard movement) may be oiled
at the rear pivot, greased at ball bearing contact,
and oiled where the guard arm actuates the
acetyl roller of the lower guard, if the down chop
motion is hard.

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

ENVIRONMENTAL PROTECTION

Waste electrical products should not be
disposed of with household waste. Please

recycle where facilities exist. Check with your

Local Authority or retailer for recycling advice.

UK PLUG REPLACEMENT

The fuse in the main plug of your power tool should
always be replaced with one of identical rating.

Check the voltage given on your power tool
matches the supply voltage.

The power tool is supplied with a tted plug,
however if you should need to t a new plug

follows the instruction below.

IMPORTANT

The wire in the mains lead are coloured in

accordance with the following code:

Blue ---Neutral
Brown ---Live

The wire that is coloured blue must be connected
to the terminal that is marked with the letter N. The
wire that is coloured brown must be connected
to the terminal that is marked with the letter L. A

13AMP (BS1363 or BS1363/A) plug must be used
and a 13AMP fuse must be tted.

13AMP

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

Declaration of Conformity

We, Importer

Erbauer (UK) Ltd.

BA22 8RT

Declare that the product:

Designation: 1400W 210mm Single Bevel Sliding Mitre Saw

Model: ERB609MSW

Complies with the essential health and safety

requirements of the following directives:

2004/108/EC – EMC Directive

2006/95/EC – Low Voltage Directive

2006/42/EC – Machinery Directive

2011/65/EU – Restrictions of the Use of Certain Hazardous

Substances in electrical and electronic equipment

2002/96/EC and 2003/108/EC Waste Electrical and Electronic Equipment (WEEE)

Standards and technical specications referred to:

EN55014-1

EN55014-2/A2

EN61000-3-2

EN61000-3-11

EN61029-1

EN61029-2-9

EN60825-1

Authorised Signatory

Date: 25/06/2010
Signature:

$ECLARATIONOF#ONFORMITY

7E)MPORTER

3CREWlX$IRECT,TD

-EAD!VENUE

(OUNDSTONE"USINESS0ARK

9EOVIL

"!24

$ECLARETHATTHEPRODUCT

-)42%3!7
3&

#OMPLIESWITHTHEESSENTIALHEALTHANDSAFETYREQUIREMENTSOFTHEFOLLOWINGDIRECTIVES

%%#%%#n%-#$IRECTIVE

%%#%%#n,OW6OLTAGE$IRECTIVE

%#n-ACHINERY$IRECTIVE

3TANDARDSANDTECHNICALSPECIlCATIONSREFERREDTO

%.!!

%.

%.!!

%.!

%.

%.

Name: Peter Harries
Erbauer (UK) Ltd
Quality Manager

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW

ERBAUER 210MM (8-1/4”) SLIDING COMPOUND MITRE SAW