Page 1
710W 115mm ANGLE GRINDER
ERB386GRD
Page 2
710W 115mm ANGLE GRINDER
Original Instructions
(Version 1.0)
Page 3
710W 115mm ANGLE GRINDER
710W 115mm ANGLE GRINDER
GUARANTEE
This product carries a 2 year guarantee. If your product develops a fault within this
period, you should in the first instance contact the retailer where the item was purchased.
This guarantee specifically excludes losses caused due to:
- Fair wear and tear
- Misuse or abuse
- Lack of routine maintenance
- Failure of consumable items (such as batteries)
- Accidental damage
- Cosmetic damage
- Failure to follow manufacturer’s guidelines
- Loss of use of the goods
This guarantee does not affect your statutory rights. This guarantee is only valid in the UK.
For further technical advice, spare parts or repair service (outside of guarantee) please contact
the customer helpline number on 0845 607 6380.
Congratulations on your purchase of a quality power tool from Erbauer (UK) Ltd. This
product should give you reliable service but for your peace of mind this
power tool does carry a 2 year guarantee, the terms of which are detailed below.
If this product develops a fault within the guarantee period contact your retailer.
Please retain this handbook in case you need to refer to safety, care or guarantee
information in the future.
Page 4
710W 115mm ANGLE GRINDER
GENERAL POWER TOOL SAFETY WARNINGS
Warning: Read all safety warnings and all instructions. Failure to follow the warnings
and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your electric (corded) power tool or batteryoperated (cordless) power tool.
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b. Do not operate power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a power tool. Distractions
can cause you to lose control.
2. Electrical safety
a. Power tool plugs must match the outlet. Never modify the plug in any way. Do
not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric shock if your
body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a power tool
will increase the risk of electric shock.
d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock.
e. When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is unavoidable, use a residual current
device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
3. Personal safety
a. Stay alert, watch what you are doing and use common sense when operating
a power tool. Do not use a power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention while operating power tools
may result in serious personal injury.
b. Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energising power tools that have
the switch on invites accidents.
d. Remove any adjusting key or wrench before turning the power tool on.
A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
Page 5
710W 115mm ANGLE GRINDER
710W 115mm ANGLE GRINDER
f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
g. If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of dust collection can
reduce dust-related hazards.
4. Power tool use and care
a. Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it on and off. Any power
tool that cannot be controlled with the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the battery pack from the
power tool before making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk of starting the power tool
accidentally.
d. Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended could
result in a hazardous situation.
5. Service
a. Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
b. If the replacement of the supply cord is necessary, this has to be done by the
manufacturer or his agent in order to avoid a safety hazard.
ADDITIONAL SAFETY INSTRUCTIONS FOR YOUR ANGLE GRINDER
Safety Warnings Common for Grinding or Abrasive Cutting-Off Operations:
1. This power tool is intended to function as a grinder, or cut-off tool. Read all safety
warnings, instructions, illustrations and specifications provided with this power
tool. Failure to follow all instructions listed below may result in electric shock, fire and/or
serious injury.
2. ALWAYS check the blade is correct fitted ,the disc outer flange is fully secured
the correct guard is fitted and correctly secured BEFORE EVERY use, operations
such as sanding, wire brushing, polishing are not recommended to be performed
with this power tool. Operations for which the power tool was not designed may create a
hazard and cause personal injury.
Page 6
710W 115mm ANGLE GRINDER
3. Do not use accessories which are not specifically designed and recommended by
the tool manufacturer. Just because the accessory can be attached to your power tool, it
does not assure safe operation.
4. The rated speed of the accessory must be at least equal to the maximum speed
marked on the power tool. Accessories running faster than their rated speed can break
and fly apart.
5. The outside diameter and the thickness of your accessory must be within the
capacity rating of your power tool. Incorrectly sized accessories cannot be adequately
guarded or controlled.
6. The arbour size of wheels, flanges, backing pads or any other accessory must
properly fit the spindle of the power tool. Accessories with arbour holes that do not
match the mounting hardware of the power tool will run out of balance, vibrate excessively
and may cause loss of control.
7. Do not use a damaged accessory. Before each use inspect the accessory such
as abrasive wheels for chips and cracks, backing pad for cracks, tear or excess
wear. If power tool or accessory is dropped, inspect for damage or install an
undamaged accessory. After inspecting and installing an accessory, position
yourself and bystanders away from the plane of the rotating accessory and run
the power tool at maximum no-load speed for one minute. Damaged accessories will
normally break apart during this test time.
8. Wear personal protective equipment. Depending on application, use face shield,
safety goggles or safety glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of stopping small abrasive or
workpiece fragments. The eye protection must be capable of stopping flying debris
generated by various operations . The dust mask or respirator must be capable of filtrating
particles generated by your operation. Prolonged exposure to high intensity noise may
cause hearing loss.
9. Keep bystanders a safe distance away from work area. Anyone entering the work
area must wear personal protective equipment. Fragments of workpiece or of a
broken accessory may fly away and cause injury beyond immediate area of operation.
10. Hold power tool by insulated gripping surfaces only, when performing an
operation where the cutting accessory may contact hidden wiring or its own cord.
Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool
“live” and shock the operator.
11. Position the cord clear of the spinning accessory. If you lose control, the cord may be
cut or snagged and your hand or arm may be pulled into the spinning accessory.
12. Never lay the power tool down until the accessory has come to a complete stop.
The spinning accessory may grab the surface and pull the power tool out of your control.
13. Do not run the power tool while carrying it at your side. Accidental contact with the
spinning accessory could snag your clothing, pulling the accessory into your body.
14. Regularly clean the power tool’s air vents. The motor’s fan will draw the dust inside the
housing and excessive accumulation of powdered metal may cause electrical hazards.
15. Do not operate the power tool near flammable materials. Sparks could ignite
these materials.
16. Do not use accessories that require liquid coolants. Using water or other liquid
coolants may result in electrocution or shock.
17. Your hand must hold on the handle when you are working. Always use the auxiliary handles
supplied with the tool. Loss of control can cause personal injury.
Page 7
710W 115mm ANGLE GRINDER
710W 115mm ANGLE GRINDER
Further safety instructions for all operations
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush
or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory
which in turn causes the uncontrolled power tool to be forced in the direction opposite of the
accessory’s rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the
wheel that is entering into the pinch point can dig into the surface of the material causing the
wheel to climb out or kick out. The wheel may either jump toward or away from the operator,
depending on direction of the wheel’s movement at the point of pinching. Abrasive wheels may
also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions
and can be avoided by taking proper precautions as given below.
1. Maintain a firm grip on the power tool and position your body and arm to allow
you to resist kickback forces. Always use auxiliary handle, if provided, for
maximum control over kickback or torque reaction during start-up. The operator
can control torque reactions or kickback forces, if proper precautions are taken.
2. Never place your hand near the rotating accessory. Accessory may kickback over
your hand.
3. Do not position your body in the area where power tool will move if kickback
occurs. Kickback will propel the tool in direction opposite to the wheel’s movement at the
point of snagging.
4. Use special care when working corners, sharp edges etc. Avoid bouncing and
snagging the accessory. Corners, sharp edges or bouncing have a tendency to snag the
rotating accessory and cause loss of control or kickback.
5. Do not attach a saw chain woodcarving blade or toothed saw blade. Such blades
create frequent kickback and loss of control.
Additional safety instructions for grinding and cutting-off operations
Safety Warnings Specific for Grinding and Abrasive Cutting-Off Operations:
1. Use only wheel types that are recommended for your power tool and the specific
guard designed for the selected wheel. Wheels for which the power tool was not
designed cannot be adequately guarded and are unsafe.
2. The guard must be securely attached to the power tool and positioned for
maximum safety, so the least amount of wheel is exposed towards the operator.
The guard helps to protect operator from broken wheel fragments and accidental contact
with wheel.
3. Wheels must be used only for recommended applications. For example: do not
grind with the side of cut-off wheel. Abrasive cut-off wheels are intended for peripheral
grinding, side forces applied to these wheels may cause them to shatter.
4. Always use undamaged wheel flanges that are of correct size and shape for your
selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of
wheel breakage. Flanges for cut-off wheels may be different from grinding wheel flanges.
5. Do not use worn down wheels from larger power tools. Wheel intended for larger
power tool is not suitable for the higher speed of a smaller tool and may burst.
Page 8
710W 115mm ANGLE GRINDER
Additional safety instructions for cutting-off operations
Additional Safety Warnings Specific for Abrasive Cutting-Off Operations:
1. Do not “jam” the cut-off wheel or apply excessive pressure. Do not attempt to
make an excessive depth of cut. Overstressing the wheel increases the loading and
susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback or
wheel breakage.
2. Do not position your body in line with and behind the rotating wheel. When the
wheel, at the point of operation, is moving away from your body, the possible kickback may
propel the spinning wheel and the power tool directly at you.
3. When wheel is binding or when interrupting a cut for any reason, switch off
the power tool and hold the power tool motionless until the wheel comes to a
complete stop. Never attempt to remove the cut-off wheel from the cut while the
wheel is in motion otherwise kickback may occur. Investigate and take corrective
action to eliminate the cause of wheel binding.
4. Do not restart the cutting operation in the workpiece. Let the wheel reach full
speed and carefully reenter the cut. The wheel may bind, walk up or kickback if the
power tool is restarted in the workpiece.
5. Support panels or any oversized workpiece to minimize the risk of wheel pinching
and kickback. Large workpieces tend to sag under their own weight. Supports must be
placed under the workpiece near the line of cut and near the edge of the workpiece on
both sides of the wheel.
6. Use extra caution when making a “pocket cut” into existing walls or other blind
areas. The protruding wheel may cut gas or water pipes, electrical wiring or objects that
can cause kickback.
Warning: Some dust particles created by power sanding, sawing, grinding, drill
and other construction jobs contain chemicals known to cause cancer, birth
defects or other reproductive harm. Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other masonry products.
• Arsenic and chromium from chemically treated timber.
Your risk from these exposures varies, depending upon how often you do this type of work. To
reduce your exposure to these chemicals:
• Work in a well-ventilated area.
• Work with approved safety equipment, such as those dust masks that are specially designed
to filter microscopic particles.
Page 9
710W 115mm ANGLE GRINDER
710W 115mm ANGLE GRINDER
VIBRATION
The European Physical Agents (Vibration) Directive has been brought in to help reduce
hand arm vibration syndrome injuries to power tool users. The directive requires power tool
manufacturers and suppliers to provide indicative vibration test results to enable users to
make informed decisions as to the period of time a power tool can be used safely on a daily
basis and the choice of tool.
Further Advice can be found at www.hse.gov.uk
Vibration total values (triax vector sum) determined according to EN 60745:
Grinding operation Vibration emission value a
h
= 7.08 m/s²
Uncertainty K = 1.5 m/s²
The declared vibration emission value should be used as a minimum level and should be
used with the current guidance on vibration.
Calculating the actual period of the actual period off use can be difficult and the HSE website
has further information.
The declared vibration emission been measured in accordance with a standardised test
stated above and may be used to compare one tool with another tool.
The declared vibration emission value may also be used in a preliminary assessment of
exposure.
Warning: The vibration emission value during actual use of the power tool can differ
from the declared value depending on the ways in which the tool is used dependant on
the following examples and other variations on how the tool is used:
How the tool is used and the materials being cut or drilled.
The tool being in good condition and well maintained
The use the correct accessory for the tool and ensuring it is sharp and in good condition.
The tightness of the grip on the handles.
And the tool is being used as intended by its design and these instructions.
While working with this power tool, hand/arm vibrations occur. Adopt the correct
working practices in order to reduce the exposure to vibration.
This tool may cause hand-arm vibration syndrome if its use is not adequately
managed.
Warning: Identify safety measures to protect the operator that are based on an
estimation of exposure in the actual conditions of use (taking account of all parts of the
operating cycle such as the times when the tool is switched off and when it is running idle in
addition to the trigger time).Note The use of other tools will reduce the users’ total working
period on this tool.
Helping to minimise your vibration exposure risk.
ALWAYS use good quality accessories.
Maintain this tool in accordance with these instructions and keep well lubricated
(where appropriate)
Page 10
710W 115mm ANGLE GRINDER
Avoid using tools in temperatures of 10ºC or less.
Plan your work schedule to spread any high vibration tool use across a number of days.
Health Surveillance
All employees should be part of an employer’s health surveillance scheme to help identity any
vibration related diseases at an early stage, prevent disease progression and help employees
stay in work.
Double insulation
The tool is double insulated. This means that all the external metal parts are electrically
insulated from the mains power supply. This is done by placing insulation barriers between
the electrical and mechanical components making it unnecessary for the tool to be earthed.
Important note
Be sure the supply is the same as the voltage given on the rating plate. The tool is fitted with
a two-core cable and plug.
Remove the mains plug from socket before carrying out, any adjustment or servicing.
Page 11
710W 115mm ANGLE GRINDER
710W 115mm ANGLE GRINDER
SYmBOLS
To reduce the risk of injury, user must read instruction manual
Warning
Double insulation
Wear ear protection Wear eye protection Wear dust mask
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority
or retailer for recycling advice.
RyyWxx Manufacturing date code; Year of manufacturing (20yy) and week of manufacturing
(Wxx); “R”: Complies with Directive 2002/95/EC on the restriction of the use of certain
hazardous substances in electrical and electronic equipment.
Page 12
710W 115mm ANGLE GRINDER
8
1
7
12
4
2
3
9
5
6
10
11
13
Page 13
710W 115mm ANGLE GRINDER
710W 115mm ANGLE GRINDER
1. ON-OFF SWITCH
2. MAIN HAND AREA
3. AUXILIARY HANDLE
4. SPINDLE LOCK BUTTON
5. OUTER FLANGE
6. INNER FLANGE
7. SPINDLE
8. GRINDING DISC
9. SPANNER
10. PROTECTION GUARD FOR GRINDING
11. CLAMPING SCREW
12. CODED PROJECTION
13. PROTECTION GUARD FOR CUTTING
Page 14
710W 115mm ANGLE GRINDER
Rated voltage 230-240V~50Hz
Rated input power 710W
Rated speed 11000/min
Protection class /II
Spindle thread M14
Disc size 115mm
Disc bore
Machine weight
22.2mm
2.3 Kg
NOISE INFORmATION
A weighted sound pressure: LpA: 88 dB (A) KPA=3.0 dB (A)
A weighted sound power: LwA: 99 dB (A) KWA=3.0 dB (A)
Wear ear protection when sound pressure is over 80dB(A)
ACCESSORIES
Metal cutting disc 1pc
Auxiliary handle 1pc
Spanner 1pc
Metal grinding disc 1pc
Wheel guard for cutting 1pc
Wheel guard for grinding 1pc
TECHNICAL DATA
Page 15
710W 115mm ANGLE GRINDER
710W 115mm ANGLE GRINDER
OPERATING INSTRUCTIONS
Note: Before using the tool, read the instruction
book carefully.
Intended Use
The machine is intended for cutting, roughing and
brushing metal and stone materials without using
water. For cutting metal, a special protection guard
for cutting ( accessory) must be used.
ASSEMBLY AND ADJUSTMENT
MOUNTING THE PROTECTIVE DEVICES
1. AUXILIARY HANDLE
For all work with the machine, the auxiliary
handle (3) must be mounted.
Screw the auxiliary handle (3) on the right or left of the
machine head depending on the working method.
(See Fig.1)
Do not make any alterations to the auxiliary
handle.
Do not continue to use an auxiliary handle if it
is damaged.
MOUNTING THE GRINDING TOOLS
Before any work on the machine itself, pull the
mains plug.
Grinding and cutting discs become very hot
while working; do not touch until they have
cooled.
1. SPINDLE LOCK BUTTON
Clean the grinder spindle and all parts to be mounted.
For clamping and loosening the grinding tools, lock
the grinder spindle (7) with the spindle lock button
(4).
Actuate the spindle lock button (4) only when
the grinder spindle is at a standstill!
2. GRINDING/CUTTING DISC
Pay attention to the dimensions of the grinding
disc. The mounting hole diameter must fit the
inner flange (6) without play. Do not use reducers
or adapters.
Mounting disc (See Fig. 2)
Screw on the outer flange (5) and tighten with the
two-pin spanner (9).
Fig. 1
Fig. 2
Page 16
710W 115mm ANGLE GRINDER
3. ADJUSTABLE OUTER FLANGE CLAMPING
The outer flange (5) should be adjusted to suit different
disc thickness. For thinner cutting discs the raised
part of the outer flange is fitted facing away from
the disc (See Fig.3-1). For thicker grinding discs the
raised part of the outer flange is fitted facing towards
the disc to provide improved support for the disc hole
(See Fig.3-2). Always ensure your disc is securely
clamped.
ADJUSTING THE PROTECTION GUARD
Before any work on the machine itself, pull the
mains plug.
For work with grinding or cutting discs, the
protection guard must be mounted.
The coded projection (12) on the protection guard
(10/13) ensures that only a guard that fits the machine
type can be mounted.
Loosen the clamping screw (11), if necessary.
Place the protection guard (10/13) with coded
projection (12) into the coded groove on the spindle
collar of the machine head and rotate to the required
position (working position).
The closed side of the protection guard (10/13)
must always point to the operator.
Tighten clamping screw (11).
OPERATION
STARTING OPERATION
To start the power tool, push the on/off switch (1)
forward.
To lock the on/off switch (1), press the on/off switch
(1) down at the front until it engages.
To switch off the power tool, release the on/off switch
(1) or, if it is locked, briefly push down the back of the
on/off switch (1) and then release it. (See Fig. 4)
OPERATING INSTRUCTIONS
• Clamp the workpiece if it does not remain stationary
due to its own weight.
• Do not strain the machine so heavily that it comes
to a standstill.
• Grinding and cutting discs become very hot while
working; do not touch until they have cooled.
• Pull the plug from the socket-outlet when not
using the machine. With the plug inserted and
mains voltage existing, the power tool still has low
power consumption even when it switched off.
Fig. 3-1
Fig. 3-2
Fig. 4
1
Page 17
710W 115mm ANGLE GRINDER
710W 115mm ANGLE GRINDER
Fig. 5
1. HAND GRIP AREAS
Always hold your angle grinder firmly with both hands
when operating (See Fig.5).
2. ROUGH GRINDING
The best roughing results are achieved when setting
the machine at an angle of 30° to 40°. Move the
machine back and forth with moderate pressure. In
this manner, the workpiece will not become too hot,
does not discolour and no grooves are formed.
Warning! Never use a cutting disc for
roughing.
3. CUTTING
Warning: For cutting metal, always work with
the wheel guard for cutting.
When cutting, do not press, tilt or oscillate the
machine. Work with moderate feed, adapted to the
material being cut.
Do not reduce the speed of running down cutting
discs by applying sideward pressure.
The direction in which the cutting is performed is
important.
The machine must always work in an up-grinding
motion. Therefore, never move the machine in the
other direction! Otherwise, the danger exists of it
being pushed uncontrolled out of the cut.
1
Page 18
710W 115mm ANGLE GRINDER
WORKING HINTS FOR YOUR ANGLE
GRINDER
If your power tool becomes too hot, run no load for
2-3 minutes to cool the motor.
Never start your angle grinder with the disc/ accessory
in contact with the workpiece.
Always start at no load to achieve maximum speed
then start working.
Do not force the disc to work faster, reducing the
Disc’s moving speed means longer working time.
When grinding, always work with a 30° to 40° angle
between disc and workpiece. Larger angles will cut
ridges into the workpiece and affect the surface
finish. Move the angle grinder across and back and
forth over the workpiece.
When using a cutting disc, never change the cutting
angle otherwise you will stall the disc and angle
grinder motor or break the disc.
When cutting, only cut in the opposite direction to
the disc rotation. If you cut in the same direction as
the disc rotation the disc may push itself out of the
cut slot.
Always ensure the workpiece is firmly held or clamped
to prevent movement.
Page 19
710W 115mm ANGLE GRINDER
710W 115mm ANGLE GRINDER
mAINTENANCE
Remove the plug from the socket before carrying
out any adjustment, servicing or maintenance.
Your power tool requires no additional lubrication or
maintenance.
There are no user serviceable parts in your power
tool. Never use water or chemical cleaners to clean
your power tool. Wipe clean with a dry cloth. Always
store your power tool in a dry place. Keep the motor
ventilation slots clean. Keep all working controls free
of dust. Occasionally you may see sparks through the
ventilation slots. This is normal and will not damage
your power tool.
If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
ENVIRONmENTAL PROTECTION
Waste electrical products should not be disposed
of with household waste. Please recycle where
facilities exist. Check with your Local Authority
or retailer for recycling advice. For further information
visit www.recycle-more.co.uk.
Page 20
PLUG REPLACEmENT
(UK & IRELAND ONLY)
If you need to replace the fitted plug then follow the
instructions below.
IMPORTANT
The wires in the mains lead are colored in accordance
with the following code:
BLUE =NEUTRAL
Brown = Live
As the colors of the wires in the mains lead of this
appliance may not correspond with the colored
markings identifying the terminals in your plug,
proceed as follows. The wire which is colored blue
must be connected to the terminal which is marked
with N. The wire which is colored brown must be
connected to the terminal which is marked with L.
Warning:
Never connect live or neutral wires to the earth
terminal of the plug. Only fit an approved 13AMP
BS1363/A plug and the correct rated fuse.
Note: If a moulded plug is fitted and has to be
removed take great care in disposing of the plug
and severed cable, it must be destroyed to prevent
engaging into a socket.
13 Amp fuse approved
to BS1362
Connect
Blue to N
(neutral)
Outer sleeve
rmly clamped
Brown L(live)
Cable grip
Page 21
710W 115mm ANGLE GRINDER
DECLARATION OF CONFORmITY
We, Importer
Erbauer (UK) Ltd BA22 8RT
Declare that the product
Description: 710W 115mm Angle grinder
Model: ERB386GRD
Complies with the following Directives,
EC Machinery Directive 2006/42/EC
EC Low Voltage Directive 2006/95/EC
EC Electromagnetic Compatibility Directive 2004/108/EC
Restrictions of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment 2002/95/EC
Waste Electrical and Electronic Equipment (WEEE) 2002/96/EC and 2003/108/EC
Standards conform to:
EN 55014-1
EN 55014-2
EN 61000-3-2
EN 61000-3-3
EN 60745-1
EN 60745-2-3
Authorised Signatory and technical file holder
Date: 07/04/11
Signature:
Name / title: Peter Harries / Quality Manager
Erbauer (UK) Ltd. Trade House, Mead Avenue, BA22 8RT
Page 22
Page 23
Page 24
Loading...