Erbauer ERB052BTE User Manual

8” THICKNESS PLANER

ERB052BTE

WARRANTY

YEARS

BTP210F-M-070928.indd 1 2007-9-28 13:35:52

GUARANTEE

This

product carries a guarantee of 24 months. If your product develops a
fault within this period, you should in the first instance contact the retailer where the
item was purchased.

This guarantee specifically excludes losses caused due to:

- Fair wear and tear

- Misuse or abuse

- Lack of routine maintenance

- Failure of consumable items (such as batteries)

- Accidental damage

- Cosmetic damage

- Failure to follow manufacturer’s guidelines

- Loss of use of the goods

This guarantee does not affect your statutory rights. This guarantee is only valid in the UK.

For further technical advice, spare parts or repair service (outside of guarantee) please
contact the customer helpline number on 0845 607 6380

Congratulations on your purchase of a quality power tool from Erbauer (UK)
Ltd. This product should give you reliable service but for your peace of mind
this

power tool does carries a 24-month guarantee, the terms of

which are detailed below.

If this product develops a fault within the guarantee period contact your
retailer.

Please retain this handbook in case you need to refer to safety, care or guarantee
information in the future.

BTP210F-M-070928.indd 2 2007-9-28 13:35:52

8” THICKNESS PLANER

SAFETY INSTRUCTIONS

Warning! When using electric tool, the following basic safety precautions

should always be taken to reduce the risk of fire, electric shock and personal
injury. Read all these instructions before attempting to operate the product and save
these instructions for future reference.

SAVE THESE INSTRUCTIONS

1. Keep the work area clean.

Cluttered areas and benches invite injuries.

2. Consider work area environment.

Do not expose power tools to rain. Do not use power tools in damp or wet locations.
Keep the work area well lit. Do not use tools in the presence of flammable liquids or
gases.

3. Guard against electric shock.

Avoid body contact with earthed or grounded surfaces (e.g. pipes, radiators, ranges,
refrigerators).

4. Keep children away.

Do not let persons, especially children, not involved in the work touch the tool or the
extension cord and keep them away from the work area.

5. Store idle tools.

When not in use, tools should be stored in a dry, high or locked up place, out of reach
of children.

6. Do not force the tool.

It will do the job better and safer at the rate for which it was intended.

7. Use the right tool.

Do not force small tools to do the job of a heavy-duty tool. Do not use tools for purposes
not intended, for example, do not use circular saws to cut tree limbs or logs.

8. Dress properly.

Do not wear loose clothing or jewellery, they can be caught in moving parts. Non-skid
footwear are recommended when working outdoors. Wear protective hair covering to
contain long hair.

9. Use protective equipment.

Use safety glasses. Use face or dust mask if working operations create dust.

10. Connect dust extraction equipment.

If the tool is provided for the connection of dust extraction and collecting equipment,
ensure these are connected and properly used.

11. Do not abuse the cord.

Never yank the tool to disconnect it from the socket. Keep the cord away from heat, oil
and sharp edges.

12. Secure work.

Where possible use clamps or a vice to hold the work. It is safer than using your hand.

13. Do not overreach.

Keep proper footing and balance at all times.

14. Maintain tool with care.

Keep cutting tools sharp and clean for better and safer performance. Follow instructions
for lubrication and changing accessories. Inspect tool cord periodically and if damaged
have them replaced by an authorised service facility. Inspect extension cords periodically
and replace if damaged. Keep handles dry, clean and free of oil or grease.

BTP210F-M-070928.indd 3 2007-9-28 13:35:53

15. Disconnect tools.

When not in use, before servicing and when changing accessories such as blades, bits
and cutters, disconnect tools from the power supply.

16. Remove adjusting keys and wrenches.

From the habit of checking to see that keys and adjusting wrenches are removed from
the tool before turning it on.

17. Avoid unintentional starting.

Ensure switch is in the “off” when plugging in.

18. Use outdoor extension leads.

When tool is used outdoors, use only extension cords intended for outdoor use and so
marked.

19. Stay alert.

Watch what you are doing. Use common sense. Do not operate tool when you are
tired.

20. Check damaged parts.

Before further use of the tool, it should be carefully checked to determine that it will
operate properly and perform its intended function. Check for alignment of moving
parts, binding of moving parts, breakage of parts, mounting and any other conditions
that may affect its operation. A guard or other part that is damaged should be properly
repaired or replaced by an authorised service centre unless otherwise indicated in this
instruction manual. Have defective switches replaced by an authorised service facility.
Do not use the tool if the switch dose not turn it on and off.

21. Warning.

The using of any accessory or attachment other than those recommended in this
instruction manual may present a risk of personal injury.

22. Have your tools repaired by qualified person.

This electrical tool complies with the relevant safety requirements. Repairs should only
be carried out by qualified persons using original spare parts, otherwise this may result
in considerable danger to the user.

BTP210F-M-070928.indd 4 2007-9-28 13:35:53

8” THICKNESS PLANER

HEALTH ADVICE

Warning! When drilling, sanding, sawing or grinding, dust particles will be

produced. In some instances, depending on the materials you are working with,
this dust can be particularly harmful to you (e.g. lead from old gloss paint).
You are advised to consider the risks associated with the materials you are working
with and to reduce the risk of exposure. You should:

- Work in a well-ventilated area.

- Work with approved safety equipment, such as those dust masks that are specially
designed to filter microscopic particles.

SPECIFIC SAFETY INSTRUCTIONS

Caution! If used incorrectly, woodworking machines can be dangerous, for this

reason always comply with the safety instructions mentioned in this manual.

1. Never work without the protective equipment prescribed for the relevant operation

and do not make any modifications to the machine that could undermine safety.

2. Children and young persons must not operate this machine. This rule does not apply

to young persons over the age of 16 being trained and supervised by an expert.

3. Prior to all work, make sure that the safety and operating equipment is securely

attached. Any parts, if damaged must be repaired correctly or replaced.

4. Set up the machine on a firm flat surface so that the table is horizontal and the

machine cannot tip over.

5. Never work with pieces which are too big or too small for the machine’s capacity.

6. Before planing, examine the workpiece for metal objects and stones and remove

them if necessary.

7. When planing, make sure that the portion of the cutter head not being used is

covered by the cutter guard.

8. When planing thin pieces of timber, suitable devices must be used to ensure that

these small pieces are properly positioned and guided.

9. The anti-kickback device of the planer must be checked regularly to ensure that it

remains in proper working condition. All pawls of this device must move freely and
must drop down by their own weight when lifted. The point of these pawls must be
kept sharp.

10. Do not begin planing until the cutter head has reached full speed.

11. When planing, take up a working position so that you are always on one side of the

machine away from the area directly in front of or behind the cutter head.

12. Always keep your hands well away from the cutter head or the chip ejection area

while the machine is running.

13. A uniform feed rate when planing increases the life of the cutting blades and reduces

the risk of accidents.

14. The planing blades must be sharpened or replaced in good time as blunt knives do

not only increase the risk of kickback, but also impose an unnecessary load on the
motor.

15. The sawdust created by planing can make it difficult to see as clearly as necessary

and can impair the operator’s health in certain circumstances.

16. If not working outdoors or in a well ventilated area, the machine should ideally be

connected to an extractor unit with an air velocity of at least 20 m/s (65.6 ft/sec.).

17. The sound pressure level at the workplace generally exceeds 85 dB (A), Users should

BTP210F-M-070928.indd 5 2007-9-28 13:35:53

therefore wear ear protectors.

18. Any repairs to the planer thicknesser must be carried out only by a suitably qualified

person.

19. Only original spare parts and accessories must be used, Otherwise the manufacturer

does not offer any warranty and does not accept any liability for personal injury.

20. Regular cleaning of the machine is an important safety factor, before beginning this

task always ensure the planer is turned off and that the plug is removed from the
mains supply.

ADDITIONAL SAFETY INSTRUCTIONS FOR PLANER
THICKNESSERS

Warning! Before connecting the tool to the mains supply be sure that the voltage

supply is the same as that specified on the nameplate of the tool. A power source
with a voltage greater or lower than that specified for the tool can result in serious
injury to the user, as well as damage to the tool. If in doubt, do not plug the tool into the
mains supply. Always turn the machine off and remove the plug from the mains socket
before making any adjustments or maintenance, including changing the blades.

1. When an extension cable is required, you must ensure that it has the right ampere

rating and a large enough cross section for the planer thicknesser, it should also
be checked to make sure that no damage is present and it is in safe electrical
condition.

2. Ensure that you have removed foreign objects such as nails and screws front the

work before commencing.

3. Rags, cloths, cord, string and anything that could get “dragged” into the cutter block

should be removed from the work area prior to use.

4. Damaged or contaminated work pieces may cause unwanted hazards. Metal parts

penetrated into the workpiece can be very dangerous, and should be removed
before operation starts.

5. Use safety equipment including safety goggles or shield, ear protection, dust mask

and protective clothing.

6. Check to make sure that all fixing screws are tight before operating the tool.

7. Ensure that the dust extractor is in place before commencing operation.

8. Do not force the workpiece through the machine, let the machine apply the correct

automatic feed rate.

9. Keep the feed rollers free of wood chips and sawdust, if the movement becomes

clogged, kickback can occur.

10. The machine is designed for the planing of wood only. Never to cut recesses,

tennons or moulds.

11. Do not use the machine for planing wood with numerous knots or loose knots.

12. Do not stand directly in front of the machine during operation, stand to one side.

13. Check that the blades are fitted correctly before commencing operation.

14. Take care when handling blades and the cutter head. Wear work gloves The blades

are sharp and can easily cut bare hands.

15. Allow the machine to reach full speed before feeding in a workpiece.

16. Check that the cutters are securely fastened.

17. Check the amount of cut on the blade before feeding in a workpiece.

18. Check that the cutters are securely fastened.

BTP210F-M-070928.indd 6 2007-9-28 13:35:53

8” THICKNESS PLANER

SYMBOLS

Read the manual Warning Wear gloves

Wear dust mask,eye & ear protection

Conforms to relevant safety standards

19. Check the amount of cut on the blade before using the machine.

20. Never attempt a heavy cut in short stock.

21. Avoid cutting across the grain.

22. Use the push pads to keep your hands well away from the blades, particularly for

shorter stick planing. Do not attempt to feed work pieces that are shorter than the
minimum length specified in the technical data of the tool.

23. Advance the material to the cutting head for normal operation by sliding it along the

table, never by placing it directly on the cutting head.

24. Never leave the machine set to a heavy cut, always reduce it to a minimum cut.

25. Use cutting blades designed for this machine only.

26. Rectify the faults including guards and cutter block immediately as they are

discovered.

BTP210F-M-070928.indd 7 2007-9-28 13:35:54

1. ON/OFF (NVR) SWITCH

2. MOTOR OVERLOAD SWITCH

3. RUBBER (ANTI VIBRATION) FEET

4. THICKNESSER EXTENSION RAIL

5. CUT DEPTH CONTROL KNOB (PLANER MODE)

6. ADJUSTABLE (IN-FEED) TABLE (PLANER MODE)

7. CHIP EXTRACTION OUTLET

8. GUIDE FENCE

9. BLADE (CUTTER) GUARD

10. BLADE GUARD LOCKING KNOB

11. HEIGHT ADJUSTING HANDLE (THICKNESSING MODE)

12. BLADE GUARD ANGLE LOCKING KNOB

7

6

5

4

3

2

1

9

10

11

12

13

14

15

8

21

16

20

19

18

BTP210F-M-070928.indd 8 2007-9-28 13:35:54

8” THICKNESS PLANER

13. FIXED (OUT-FEED) TABLE (PLANER MODE)

14. BLADE GUARD ARM ASSEMBLY

15. SAFETY INTERLOCK SWITCH

16. 45° FENCE ANGLE STOP

17. ANGLE POINTER

18. 90° FENCE ANGLE STOP

19. ANGLE GUIDE

20. FENCE ANGLE LOCK HANDLE

21. CABLE CLIPS

TECHNICAL DATA

Volts: 230V~50Hz

Power: 1280W

No load speed: 8,500min

-1

Max. planing width: 204mm

Max. depth of cut (planer): 3mm

Max. depth to cut (thicknesser): 2mm

Planing height: 5-120mm (Thicknesser)

Feed speed: 8m/min (Thicknesser)

Table size: 740x210mm (Planer)

250x204mm (Thicknesser)

Machine weight: 27.5kg

NOISE AND VIBRATION DATA

Sound pressure level: 92.9dB

Sound power level: 105.9dB

BTP210F-M-070928.indd 9 2007-9-28 13:35:54

ACCESSORIES

Crank 1pc
Parallel guide 1set
Dust collector 1pc
Push block 2pcs
Blade setting gauge 1pc
Hex key 3pcs
Spanner 1pc
Subassembly stand cushion 1set
Safety guard plate 1pc

BTP210F-M-070928.indd 10 2007-9-28 13:35:54

8” THICKNESS PLANER

ASSEMBLY

1. Fitting the rubber (anti-vibration) feet
(See Fig 1):

1) Carefully turn the machine upside down, taking
care not to damage the in-feed / out-feed beds.

2) Fit the washers over the hex bolts and push
both through the holes in the rubber feet.

3) Fit the feet / bolts to the holes provided (1 on
each corner of the machine).

4) Secure using a 6 mm hex key.

2. Fitting the guide fence (8 )(See Fig 2-4):

1) Locate the 2 x guide fence mounting holes
situated on the side of the planning out-feed table
(13).
Then place the safety guard plate. (Fig 3)

2) Line up the 2 x mounting holes on the guide
fence (8) with those situated on the out-feed table
(13).

3) Fit the 2 x supplied hex head screws through
both sets of holes and tighten to secure.
Note: Do not over-tighten the screws as this will
cause un-wanted damage to the aluminium out­feed table. Rather just tighten until the fence is
secured.

Fig 2

Fig 1

Fig 3

Fig 4

BTP210F-M-070928.indd 11 2007-9-28 13:35:55

3. Fitting the blade (cutter) guard (9) (See
Fig 5-9):

1) Familiarise yourself with the blade guard
locating pivot pin (a), and the blade guard limiting
screw pole (b) situated on the side of the planer
out-feed table (13).

2) Remove the limiting screw.

3) Slide the guard arm assembly (14) over the
locating pivot pin.

4) Replace the limiting screw and tighten to
secure.

5) Fitting the cutter guard to the guard assembly
arm (14):

• Set out the parts as shown in Fig 9.

• Slide the arm into the guard.

• Ensure the holes on the guard and arm line up.

• Push the threaded spacer through the holes.

• Secure with the thumbscrew.

Fig 6

Fig 7

Fig 8 Fig 9

a b

Fig 5

BTP210F-M-070928.indd 12 2007-9-28 13:35:55

8” THICKNESS PLANER

OPERATION

Important: This planer-thicknesser is intended
specifically for planning and thicknessing
operations on solid timber. When being thickened,
the contact surface of the work piece must be flat.
If working with bigger or heavier work-pieces it
is necessary to clamp the machine firmly to its
supporting bench or table. The machine is not
suitable for operation outdoors when raining or
in any damp environment. Any other use beyond
this scope is considered as failing to comply with
the machines intended purpose. The manufacturer
is not liable for any damage or injuries caused
as a result of this; the risk is borne solely by the
user.
The ON / OFF (NVR) switch (1) of machine is
located on the left side below
the yellow cover.
To switch the machine on: Lift the yellow cover
and press the green button “1”.
To switch the machine off: Press the red button
“0” or firmly close the cover.
The switch can be locked to prevent the machine
from being inadvertently switched on by folding
down the yellow cover.
This machine is equipped with an overload
switch (2) for motor running protection. Once
the overload occurs, the machine will stop
automatically. After a while, the overload switch
can be reset.

Warning: Operation of any power tool can

result in foreign objects being thrown into
the eyes which can result in severe eye injury.
Always wear safety goggles, it is also advisable
to wear ear protection particularly if using the
planer for extended periods.
For your own safety, read all of the safety
instructions in this manual and adhere to all
precautions before and during operation of the
planer thicknesser.

Before each use:

• Make sure all moving parts are free from
interference.

• Make sure blades are aligned and correctly
attached to cutter-head (See maintenance section
of this manual).

• Do not plug in the planer thicknesser unless the

BTP210F-M-070928.indd 13 2007-9-28 13:35:55

switch is in “off’ position.

• After turning the switch on, allow the cutter
block to come to full speed before commencing
the operation.

• Keep hands clear of all moving parts.

• Do not force the cut. Slowing or stalling the
cutter will force the overload to cut in and will
greatly reduce the life of the motor.

• Use quality dry timber. Blades last longer and
cuts are smoother with good quality wood.

• Do not pull the workpiece back over the cutter
block towards the infeed table.

• Support the work-piece adequately at all times
during operation; maintain control of the work­piece.

• Take precautions against kickback, do not permit
anyone to stand or cross in the line of cutter­head’s rotation. Kickback or thrown debris will
travel in this direction.

• Replace or sharpen blades as they become
damaged or dull.

• Whenever possible always use the push blocks
supplied to feed work across the cutter head.

1. Planing mode:

1.1 Setting the guide fence (8). (See Fig 10-

11)

1) Turn the fence angle locking handle (20) anti­clockwise to loosen.

2) Use the angle guide (19) and the angle pointer
(17) to set the fence at the desired angle.

3) Re-tighten the locking handle (20) to secure the
fence guide (8).
Note: There are positive stops at 45° and 90°
this is to make it easier to set the fence at these 2
popular angles.

1.2 Fitting the extraction port. (See Fig 12-

17)

The dust extraction port (F) is also one of the
safety devices of the planer thicknesser. Once
fitted correctly, the extraction port covers the
underside of the cutter-block and engages one
of the safety interlock switches, which allows the
machine to run safely.

1) Fit the height adjusting handle (11) over its
shaft.

2) Turn the crank anti-clockwise, this will lower the
thicknesing table.

Fig 11

Fig 12

Fig 13

Fig 10

BTP210F-M-070928.indd 14 2007-9-28 13:35:56

8” THICKNESS PLANER

a

3) Continue turning the handle until the thicknesser
table reaches its lowest point.

4) On the bottom of the thicknesser table there
are 3 holes, these are the locating holes for the
corresponding locating points on the extraction
port assembly.

5) Make note of “tab a” as this is the point that
engages the interlock switch and allows the
planer thicknesser to run safely.

6) Take care to ensure that this “tab” is located
correctly whilst fitting the dust extraction port.

7) Hold the dust extraction port assembly at
approximately 45° and slide it into place onto the
thicknesser bed.

8) Ensure that the 3 locating points line up with
the corresponding holes on the thicknesser bed
and set the port flat against the bed.

9) Secure the extraction port by fitting and
tightening the supplied nut onto the middle
(threaded) locating point.

10) Turn the height adjusting handle (11) clockwise
to raise the thicknesser bed. This will secure the
extraction port in place as well as engaging the
safety interlock switch.
Caution: Do not secure the extraction port too
tightly If too much force is applied to the height
adjusting handle the extraction port will go
beyond its optimum position, the safety interlock
switch will disengage and the motor will not run.

11) Once fitted correctly, the extraction port should
look as in Fig 16.

12) Finally, fit the extraction port adapter (E) by
simply sliding it over the extraction port as in
Fig17.

Fig 15

Fig 14

Fig 16

Fig 17

BTP210F-M-070928.indd 15 2007-9-28 13:35:56













1.3 Setting the blade guard (9). (See Fig 18-

19)

1) Loosen the blade guard locking knob (10).

2) Pull back the blade guard (9).

3) Set the workpiece against the guide fence (8).

4) Slide the blade guard (8) towards the workpiece
(leaving a small gap of a few millimetres).

5) Re-tighten the blade guard locking knob (10) to
secure.
Caution: When the machine is not in use the
plug should be removed from the mains socket
and the blade guard (9) should be set so that it
covers the whole of the cutter assembly so as to
reduce the risk of injury.

1.4 Setting the depth of cut. (See Fig 20)

The depth of cut is the amount of material
removed from the workpiece with a single pass
over the cutter-block. It is set by the in-feed table
moving up / down in relation to the out-feed table
(this is fixed).
Note: The maximum cut of 3mm should only be
utilized on softer woods. The planer thicknesser
will give a much better quality finish on harder
woods such as oak if less material is removed on
each pass.

1) Turn the cut depth control knob (5) clockwise
to reduce the depth of cut and anti-clockwise to
increase the depth of cut.

2) The scale to the left of the in-feed table shows
the amount of material that will be removed per
pass.

3) 1 relates to approximately 1mm, 2 relates to
approximately 2mm etc.

1.5. Planing mode: Making a pass with the
workpiece. (See Fig 21)

Once everything is set as needed the planer
thicknesser can now be safely operated.

1) Ensure that the cutter block is free from foreign
objects (including the workpiece to be planed).

2) Connect the planer thicknesser to the mains
supply.

3) Turn the planer on with the green “1” button
(1).

4) Allow the planer to reach its maximum speed.

5) Place the workpiece onto the in-feed table and
ensure that the workpiece stays parallel with the
in-feed table for the whole pass.

6) Slowly push the workpiece forward (over the

Fig 19

Fig 18

Fig 20

Fig 21

BTP210F-M-070928.indd 16 2007-9-28 13:35:57

8” THICKNESS PLANER







cutter-block).
Caution: It is much safer (particularly when using
a thin / small workpiece)
to use the supplied push blocks.

7) Repeat these steps until the correct amount of
material has been removed.
Note: Keep firm and even pressure on the
workpiece as it passes over the in-feed table and
continue pushing forward until the back of the
workpiece passes the cutter-block.

2. Thicknesser mode:

2.1 Setting the blade guard (9). (See Fig 22-

23)

1) Loosen the blade guard locking knob (10) (turn
clockwise).

2) Slide the blade guard (9) out as far as it will
go.

2.2 Thicknesser mode: Fitting the extraction
port. (See Fig 24-26)

There are 2 holes on the out-feed table of the
planer, 1 x un-threaded hole (a) for locating the
extraction port, and 1 x threaded hole (b) for
securing the extraction port as shown in Fig 24.
These holes work in conjunction with the fixings
on the extraction port.

1) Insert the locating pin (a) on the extractor port
into the locating pin hole (a) on the out-feed
table.

2) Tighten the securing screw (b) on the extraction
port into the securing pin hole (b) on the out-feed
table.

3) Ensure tab (c) sits over the machines 2nd
interlock safety switch. You will hear the switch
click as the securing screw is tightened.

4) Slide the extraction port adapter (7) over the
extractor port.

Fig 23

Fig 23

Fig 24

Fig 25

a

b

BTP210F-M-070928.indd 17 2007-9-28 13:35:58









2.3 Thicknesser mode: Setting the depth of
cut. (See Fig 27)

The depth of cut is set by how high / low the
thicknessing bed is in relation to the cutter-block.

1) Measure the workpiece.

2) Set the bed to just over this measurement,
using the scale to the left of the in-feed table.

3) Turn the height adjusting handle (11) anti­clockwise to lower the thicknessing bed, clockwise
to raise it.

4) Ensure that the cutter block is free from
foreign objects (including the workpiece to be
thickened).

5) Connect the planer thicknesser to the mains
supply.

6) Turn the thicknesser on with the green “1”
button (1).

7) Allow the planer to reach its maximum speed.

8) Place the workpiece onto the in-feed table.

9) Turn the height adjustment handle (11) half a
turn clockwise to raise the bed.

10) Continue this process until the workpiece
comes into contact with the thicknesser drive
rollers.

11) Once the workpiece comes into contact with
the rollers they will automatically “pull” it through
the machine and over the cutterblock.

12) Continue this process until the workpiece is at
the desired thickness.
Note: A longer workpiece should be supported
after it leaves the machine to ensure a good even
finish.

MAINTENANCE

Caution: Always ensure that the machine

is turned off and that the plug is removed
from the mains supply before carrying out any
repairs or maintenance.

1. Before each use.

• Check for damaged parts and repair or replace
them as necessary.

• Ensure all nuts and bolts etc are secure.

• Ensure that all moving parts move freely and are
not binding prior to starting the machine.

• Remove adjusting keys and wrenches and check
to see that keys and adjusting wrenches are

Fig 27

Fig 26

BTP210F-M-070928.indd 18 2007-9-28 13:35:59

8” THICKNESS PLANER

removed from the tool before turning it on.

2. During use.

• Constantly check for abnormalities. Stop the
operation immediately if something does not look
or sound right and have the machine checked by
a suitably qualified person.

• Remove any buildup of chippings and pay
particular attention around the base of the planer
thicknesser, as build up there will prevent the
cooling air from reaching the motor.

3. After each use.

• Remove the extraction port and clean out all
chippings etc. Dry air would be good for this
operation but a soft brush would also work.
Caution: Always wear a dust mask and eye
protection when using dry air.

• Remove all chippings etc from the planer
thicknesser.

• Remove all chippings etc from around the air
inlets of the motor. If these become blocked the
motor will become too hot and its service life will
be greatly reduce.

• Wrap the mains lead carefully around the cable
clips (21). This will reduce the risk of tripping and
/ or damage to the cable.

4. After 10 hours running. (See Fig 28)

• Lubricate the bush bearings.

• Treat the threaded spindles for height adjustment
of the thicknessing table with dry lubricant.

5. Periodically. (See Fig 29)

Over time resin or other contaminates may build
up on the planer in-feed and out-feed tables, as
well as the thicknesser table and the in-feed and
out-feed rollers.

• To ensure easy steady feeding the beds and the
rollers will need to be cleaned periodically.

• Periodically check that the anti-kickback fingers
move freely (they should fall back under their
own weight).

• Check that the points of the anti-kickback fingers
are not rounded.









Fig 28

Fig 29

BTP210F-M-070928.indd 19 2007-9-28 13:36:00





































6. Setting the positive stops on the guide
fence:(See Fig 30-32)

The positive stops at 90° and 45° are set at the
factory to ensure accuracy, however over time
they may need to be reset.

• Loosen the fence angle lock handle (20).

• Sit a 90° square firmly on the planer table.

• Set the guide fence against the square, this will
give an angle of 90° between the bed and the
fence.

• Loosen the lock nut (a).

• Tighten / loosen the angle locking bolt until it sits
against the angle stop on the angle guide (19),
whilst ensuring that the 90° angle is kept.

• Re-tighten the lock nut to hold the bolt securely
in place.

• Loosen the angle pointer screw (c) and set the
angle pointer so that it reads 90°.

• To set the 45° positive stop, set the guide fence
so that the angle pointer is at 45° .

• Loosen the 45° lock nut (b).

• Tighten / loosen the angle locking bolt until it sits
against the 45° stop on the angle guide.

• Re-tighten the locking nut to secure.

Fig 31

Fig 30

Fig 32

BTP210F-M-070928.indd 20 2007-9-28 13:36:01

8” THICKNESS PLANER







7. Replacing the cutter blades:

1) Removing the blades. (See Fig 33-35)

Caution: Not to touch the tips of the blades

as it would cause hurts to you.

• Remove the guide fence (8).

• Loosen the blade guard locking screw (10) and
slide the blade guard (9) away from the cutter­block as far as it will go.

• Turn the cutter-block so that one of the blades is
exposed in the gap between the in-feed (6) and
out-feed (13) tables.

• Turn the five blade tensioning screws (anti­clockwise) to loosen.

• Once all five screws have been loosened, the
blade complete with the blade clamping device
can be easily removed.
Note: Remember the correct orientation of the
blade to ensure that the new one can be fitted
correctly.

Caution: Take care not to lose the blade
tensioning springs from the cutter-block

after the blade assembly has been removed.

• Whilst removed, all parts (including the cutter­block) should be thoroughly cleaned.

Fig 34

Fig 33

Fig 35

BTP210F-M-070928.indd 21 2007-9-28 13:36:02

2) Fitting the blades: (See Fig 36-38)

• Fit the blade correctly into the clamping device.

• Slide both components into the cutter-block,
taking care that they are fitted in the correct
direction etc.

• Centre the blade assembly laterally.

• Set the blade setting block (C) over the cutter­block.

• Pull the setting block back so that it sits firmly
against the front edge of the planing out-feed
table (13).

• Put firm downward pressure on the setting
block whilst keeping it firmly against the edge of
the out-feed table. This will push the blade into
place.

• Keep firm pressure on the setting block and
tighten the 5 blade tensioning screws.

• Once complete, turn the cutter-block to expose
the 2nd blade and repeat the process to replace

that blade.
Note: Once this operation is complete, ensure
that the cutter-block turns freely by hand before
re-connecting the machine to the mains supply.
Replace all safety guards immediately after
completing this operation.

Fig 37

Fig 36

Fig 38

BTP210F-M-070928.indd 22 2007-9-28 13:36:03

8” THICKNESS PLANER

8. Replacing the motor brushes: (See Fig
39-41)

Caution: This operation should only be

carried out by a suitably qualified person.

• Carefully turn the planer thicknesser onto its
side.

• This will expose the motor of the machine.

• Take a slotted screwdriver (not supplied) and
locate it in the slot on the motor brush cap.

• Turn the screwdriver anti-clockwise until the cap
can be removed and take care when removing
the cap as there is a spring under compression
holding the brush in place.

• Remove the brush and check the length; If the
brush needs changing fit the new brush and
tighten the cap to retain it.
If the brush is not worn but is sticking inside the
holder there may be carbon buildup that needs to
be removed. The best way to remove the carbon
is by blowing dry air into the holder, but a small
stiff brush or pipe cleaner could be used to do
the same job. The brush will also need cleaning
as some of the buildup may be stuck to it.

Caution: When removing or cleaning the

brushes eye protection and a dust mask
should be worn; particularly if using dry air. Clean
or change the brushes in a well ventilated area
and ensure everyone in that area also wear the
appropriate protection.

Fig 40

Fig 39

Fig 41

BTP210F-M-070928.indd 23 2007-9-28 13:36:03

TROUBLESHOOTING

Caution: Troubleshooting could lead to an increased risk to the operator due

to the fact that safety guards / covers may have to be removed. It is therefore
particularly important that all the measures necessary for safe working are taken.

Fault Possible causes Possible solutions

Machine will not run No mains voltage. Check the supply.

Fuse blown. Check the fuse and replace

if necessary.

Overload switch has cut
in.

Allow the machine to cool
and reset the switch.

Faulty NVR switch. Check and replace if

necessary.

Carbon brushes worn. Check and replace if

necessary.

Faulty motor. Check and replace if

necessary.

Damaged mains lead. Check and replace if

necessary.

Safety interlock switch is
not correctly engaged

Check that the extraction
port is correctly seated.

Speed drops whilst the
machine is under load.

Cutting depth is too great. Reduce the cutting depth.

Feed rate is too fast. Reduce the feed rate.

Dull cutter blades. Replace / sharpen the

cutter blades.

The motor cuts out whilst
under no load.

Mains failure. Check the supply.

Motor has exceeded its
duty cycle.

Allow the motor to cool
and reset the overload.

Faulty motor. Check and replace if

necessary.

Faulty NVR switch. Check and replace if

necessary.

BTP210F-M-070928.indd 24 2007-9-28 13:36:04

8” THICKNESS PLANER

The motor cuts out whilst
under load.

Motor has exceeded
its duty cycle and the
overload has cut in.

Allow the motor to cool
and reset the overload.

Cutting depth is too great
so the overload has cut in.

Allow the motor to cool
and reset the overload.
Reduce the cutting depth.

Feed rate is too fast so the
overload has cut in.

Allow the motor to cool
and reset the overload.
Reduce the feed rate.

Dull cutter blades so the
overload has cut in.

Replace or sharpen the
blades, allow the motor
to cool and reset the
overload.

Poor finish on workpiece. Dull or damaged blades. Replace or sharpen the

blades.

Uneven feed rate. Ensure constant pressure

on the wor piece whilst
planing.

Feed rate too fast. Reduce the speed of feed.

Extraction port becomes
blocked whilst thicknessing
(without external
extraction).

Cutting depth too great. Reduce the cutting depth.

Wood is too damp. Allow the wood to dry.

Extraction port becomes
blocked whilst planing
(without external
extraction)

Cutting depth too great. Reduce the cutting depth.

Feed rate too fast. Reduce the feed rate.

Wood is too damp. Allow the wood to dry.

BTP210F-M-070928.indd 25 2007-9-28 13:36:04

ENVIRONMENTAL PROTECTION

Waste electrical products should not be
disposed of with household waste. Please
recycle where facilities exist. For further

information visit www.recycle-more.co.uk

PLUG REPLACEMENT

If you need to replace the fitted plug then follow
the instructions below.

Important

The wires in the mains lead are coloured in
accordance with the following code:

Green & yellow - Earth
Blue - Neutral
Brown - Live

As the colours of the wires in the mains lead
of this appliance may not correspond with the
coloured markings identifying the terminals in
your plug, proceed as follows. The wire which is
coloured green & yellow must be connected to
the terminal which is marked with E or .
The wire which is coloured blue must be
connected to the terminal which is marked with
N. The wire, which is coloured brown, must be
connected to the terminal, which is marked with
the letter L.
Warning: Never connect live or netutral wires
to the earth terminal of the plug. Only fit an
approved 13 Amp BS1363/A plug and the correct
rated fuse.

Note: If a moulded plug is fitted and has to be
removed take great care in disposing of the
plug and severed cable, it must be destroyed to
prevent engaging into a socket.
If the supply cord is damaged it must be replaced
by a service agent or a similarly qualified person
in order to avoid hazard.

BTP210F-M-070928.indd 26 2007-9-28 13:36:06

8” THICKNESS PLANER

Declaration of Conformity

We, Importer

Erbauer (UK) LTD BA22 8RT

Declare that the product

8” THICKNESS PLANER

ERB052BTE

Complies with the essential health and safety requirements of the following directive:

2004/108/EC. –EMC Directive.

73/23 EEC, 93/68 EEC. –Low Voltage Directive.

98/37 EC. –Machinery Directive.

2002/95/EC Restrictions of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment

Standards and technical specifications referred to:

EN 61029-1: 2000/+A11: 2003+A12: 2003

prEN 61029-2-3:2004

EN 55014-1:2000/+A1: 2001+A2: 2002

EN 55014-2: 1997/+A1: 2001
EN 61000-3-2:2000+A2:2005

EN 61000-3-11: 2000

2007

Authorised Signatory

Date: 01/01/07

Signature:

Name: Peter Harries
Erbauer (UK) Ltd
Quality Manager

BTP210F-M-070928.indd 27 2007-9-28 13:36:06

BTP210F-M-070928.indd 28 2007-9-28 13:36:06