Page 1
MNL_EHP18-Li_V01_180608
EAN. 3663602799689
EHP18-Li
ORIGINAL INSTRUCTIONS
Page 2
Safety instructions
Product description
Assembly
Use
Care & maintenance
Guarantee
x1
WARNING!
that they are fully understood before handling the tool.
Please read all safety warnings carefully and be sure
Declaration of Conformity
2
3
Page 3
PRODUCT DESCRIPTION
1
2
1
19
12 13
11
24 23
4
5 6
A1
7 8
A2
2
3
9
B1 B2
22
C D
15
16
10
26
17
18
21a
25
14
21b
4
21
20
E F
5
Page 4
22
23
15
25
+
G H
I J
K
O1
15
P
O2
26
-
Q
L
45°
M N
6
b
a
7
Page 5
SAFETY INSTRUCTIONS
GENERAL POWER TOOL SAFETY WARNINGS
WARNING! Read all safety warnings, instructions,
illustrations and specications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, re and/or serious injury.
Save all warnings and instructions for future
reference. The term “power tool” in the warnings refers
to your mains-operated (corded) power tool or battery
operated (cordless) power tool.”
WORK AREA SAFETY
a. K
eep work area clean and well lit. Cluttered or dark areas
invite accidents.
b. D
o not operate power tools in explosive atmospheres,
such as in the presence of ammable liquids, gases or dust.
Power tools create sparks which may ignite the dust or fumes.
c. K
eep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
a. Pow
b. Av
er tool plugs must match the outlet. Never modify the
plug in any way. Do not use any adapter plugs with earthed
(grounded) power tools. Unmodied plugs and matching
outlets will reduce risk of electric shock.
oid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators. There
is an increased risk of electric shock if your body is earthed or
grounded.
c. Do n
ot expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electric shock.
d. Do
not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
e. W
hen operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If
operating a power tool in a damp location is unavoidable,
use a residual current device (RCD) protected supply. Use
of an RCD reduces the risk of electric shock.
PERSONAL SAFETY
a. St
ay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power tool
while you are tired or under the inuence of drugs, alcohol
or medication. A moment of inattention while operating power
tools may result in serious personal injury.
b. Use
personal protective equipment. Always wear eye
protection. Protective equipment such as a dust mask, non-
skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
c. Pr
event unintentional starting. Ensure the switch is in
the off- position before connecting to power source and/
or remove battery pack, picking up or carrying the tool.
Carrying power tools with your nger on the switch or energising
power tools that have the switch on invites accidents.
d. Re
move any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating
part of the power tool may result in personal injury.
e. Do
not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
8
9
Page 6
f. Dre
ss properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing away from moving parts. Loose
clothes, jewellery or longhair can be caught in moving parts.
g. If
devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
h. D
o not let familiarity gained from frequent use of tools
allow you to become complacent and ignore tool safety
principles. A careless action can cause severe injury within a
fraction of a second.
POWER TOOL USE AND CARE
a. D
o not force the power tool. Use the correct power tool for
your application. The correct power tool will do the job better
and safer at the rate for which it was designed.
b. D
o not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c. Di
sconnect the plug from the power source and/or romove
the battery pack, if detachable, from the power tool before
making any adjustments, changing accessories, or storing
power tools. Such preventive safety measures reduce the risk
of starting the power tool accidentally.
d. S
tore idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate
the power tool.
Power tools are
dangerous in the hands of untrained users.
e. M
aintain power tools and accessories. Check for
misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the power
tools operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly maintained
power tools.
10
f. K
eep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind and
are easier to control
g. Us
e the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into account
the working conditions and the work to be performed. Use
of the power tool for operations different from those intended
could result in a hazardous situation.
h. K
eep handles and grasping surfaces dry, clean and free
from oil and grease. Slippery handles and grasping surfaces
do not allow for safe handling and control of the tool in
unexpected situations.
BATTERY TOOL USE AND CARE
a. R
echarge only with the charger specied by the
manufacturer. A charger that is suitable for one type of battery
pack may create a risk of re when used with another battery
pack.
b. U
se power tools only with specically designated battery
packs. Use of any other battery packs may create a risk of
injury and re.
c. When
battery pack is not in use, keep it away from other
metal objects, like paper clips, coins, keys, nails, screws
or other small metal objects, that can make a connection
from one terminal to another. Shorting the battery terminals
together may cause burns or a re.
d. Unde
r abusive conditions, liquid may be ejected from the
battery; avoid contact. If contact accidentally occurs,
ush with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause
irritation or burns.
e. Do
not use battery pack or tool that is damaged or
modied. Damaged or modied batteries may exhibit
unpredictable behaviour resulting in re, explosion or risk of
injury.
11
Page 7
f. Do
not expose a battery pack or tool to re or excessive
temperature. Exposure to re or temperature above 130 °C
may cause explosion.
g. Fo
llow all charging instructions and do not charge the
battery pack or tool outside the temperature range
specied in the instructions. Charging improperly or at
temperatures outside the specied range may damage the
battery and increase the risk of re.
SERVICE
a. Ha
ve your power tool serviced by a qualied repair person
using only identical replacement parts. This will ensure that
the safety of the power tool is maintained.
b. N
ever service damaged battery packs. Service of battery
packs should only be performed by the manufacturer or
authorized service providers.
PLANER SAFETY WARNINGS
a. Wait for the cutter to stop before setting the tool down.
An exposed rotating cutter may engage the surface leading to
possible loss of control and serious injury.
b. Use clamps or another practical way to secure and support
the workpiece to a stable platform. Holding the work by your
hand or against the body leaves it unstable and may lead to
loss of control.
ADDITIONAL SAFETY WARNINGS FOR BATTERY
a.
Do not connect the positive terminal and negative terminal of
the battery to each other with any metal object (such as wire).
b.
Do not carry or store battery together with necklaces, hairpins
or other metal objects.
c.
Do not pierce the battery with nails, strike the battery with a
hammer, step on the battery or otherwise subject it to strong
impacts or shocks.
d.
Do not solder directly onto the battery.
e.
Do not expose battery to water or salt water, or allow the
battery to get wet.
f.
Do not disassemble or modify the battery.
g.
Do not place the battery in or near re, on stoves or other
high temperature locations. Do not place the battery in direct
sunlight, or use or store the battery inside cars in hot weather.
h.
Do not place the battery in microwave ovens, high-pressure
containers or on induction cookware.
i.
If you intend to store a battery for a period without use then
store battery at room temperature (19°C to 25°C), charged
to about 30 – 50% of capacity. When storing for very long
periods boost charge the battery once per year to prevent over
discharge.
c. Be aware of kickback.
d. Turn the product off immediately, if the cutting blade gets jammed.
e. Never slow down the application tool yourself mechanically.
Always allow the product to come to complete stop on its own.
f. Never touch the workpiece with your hand when you are
working on it.
g. Do not work overhead.
h. Ensure that the workpiece is free of foreign objects such as
screws or nails.
12
13
Page 8
The following information applies to professional users only but is
good practice for all users:
2. Using a different method of work altogether – e.g. using a nail
gun to direct fasten cable trays instead of drilling holes rst.
ADDITIONAL SAFETY WARNING FOR CONSTRUCTION DUST
The updated Control of Substances Hazardous to Health
Regulations 1st October 2012 now also targets to reduce the
risks associated with silica, wood and gypsumdusts. Construction
workers are one of the at-risk groups within this because of the
dust that they breathe: silica dust is not just a nuisance; it is a real
risk to your lungs!
Silica is a natural mineral present in large amounts in things like
sand, sandstone and granite. It is also commonly found in many
construction materials such as concrete and mortar. The silica is
broken into very ne dust (also known as Respirable Crystalline
Silica or RCS) during many common tasks such as cutting, drilling
and grinding. Breathing in very ne particles of crystalline silica
can lead to the development of: Lung cancer Silicosis Chronic
Obstructive Pulmonary Disorder/Chronic obstructive pulmonary
disease (COPD) And breathing in ne particles of wood dust can
lead to the development of Asthma. The risk of lung disease is
linked to people who regularly breathe construction dust over a
period of time, not on the odd occasion.
To protect the lung, the COSHH Regulations sets a limit on the
amount of these dusts that you can breathe (called a Workplace
Exposure Limit or WEL) when averaged over a normal working
day. These limits are not a large amount of dust: when compared
to a penny it is tiny – like a small pinch of salt: This limit is the legal
maximum; the most you can breathe after the right controls have
been used.
3. Please always work with approved safety equipment, such
as those dust masks that specially designed to lter out
microscopic particles and use the dust extraction facility at all
time.
For more information please see the HSE website: http://www.hse.
gov.uk/construction or http://www.hse.gov.uk/pubns/cis69.pdf
WARNING! Some dust particles created by power
sanding, sawing, grinding, drill and other construction
jobs contain chemicals known to cause cancer, birth
defects or other reproductive harm. Some examples of
these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks and cement and other
masonry products.
• Arsenic and chromium from chemically treated timber.
• Your risk from these exposures varies, depending
upon how often you do this type of work. To reduce
your exposure to these chemicals:
• Work in a well-ventilated area.
• Work with approved safety equipment, such as those dust
masks that are specially designed to lter microscopic
particles
VIBRATION
HOW TO REDUCE THE AMOUNT OF DUST?
1. Reduce the amount of cutting by using the best sizes of building
products. Use a less powerful tool e.g. a block cutter instead of
angle grinder.
14
The European Physical Agents (Vibration) Directive has been
brought in to help reduce hand arm vibration syndrome injuries to
power tool users. The directive requires power tool manufacturers
and suppliers to provide indicative vibration test results to enable
users to make informed decisions as to the period of time a power
tool can be used safely on a daily basis and the choice of tool.
15
Page 9
SEE TECHNICAL SPECIFICATIONS IN THE INSTRUCTION
MANUAL FOR THE VIBRATION LEVELS OF YOUR TOOL.
The declared vibration emission value should be used as a minimum
level and should be used with the current guidance on vibration.
Calculating the actual period of use can be difcult and the HSE
website has further information.
While working with this power tool, hand/arm vibrations occur.
Adopt the correct working practices in order to reduce the
exposure to vibration. This tool may cause hand-arm vibration
syndrome if its use is not adequately managed.
Helping to minimise your vibration exposure risk. ALWAYS use sharp
chisels, drills and blades. Maintain this tool in accordance with
these instructions and keep well lubricated (where appropriate).
Avoid using tools in temperatures of 10ºC or less. Plan your work
schedule to spread any high vibration tool use across a number of days.
PRODUCT DESCRIPTION
1. Cutting depth scale
2. Cutting depth adjustment knob
3. Dust/Chip extraction guide switch
4. Lock-off button
5. On/off switch
6. Handle
7. Battery pack release button
8. Power bar button
9. Battery pack (not included)
10. Dust extraction outlets (×2)
11. Mounting thread (parallel guide )
12. V-groove
13. Front plate
14. Roller
15. Blade
16. Back plate
17. Blade protection foot
18. Wing screw (x2)
19. Rebate depth gauge
20. Dust bag
21. Parallel guide
22. Wrench
23. Hex screws
24. Grub screws
25. Cutter block
26. Hex key
NOTE: The use of other tools will reduce the users’ total
working period on this tool.
HEALTH SURVEILLANCE
All employees should be part of an employer’s health surveillance
scheme to help identity any vibration related diseases at an early
stage, prevent disease progression and help employees stay in
work.
RESIDUAL RISKS
Even if you are operating this product in accordance with all
the safety requirements, potential risks of injury and damage
remain. The following dangers can arise in connection with
the structure and design of this product:
1. Injuries and damage to property due to broken attachments or
the sudden impact of hidden objects during use.
2. Danger of injury and property damage caused by ying objects
or poor power tool accessories.
16
TECHNICAL SPECIFICATIONS
01
Planer
Rated voltage: 18V d.c.
Rated no load speed: 14000/min
Planing width: 82 mm
Cutting depth: 0-2mm
Rebating depth: 0-8mm
Weight(without battery): 2.3 kg
For use with battery pack and charger as below:
Battery pack model: EBAT18-Li-2 / EBAT18-Li-4 / EBAT18-Li-5
Charger model: EC18-Li / EFC18-Li / EMC18-Li
o
Ambient temperature range for tool and battery use: -10
NOISE DATA
A weighted sound pressure: L
A weighted sound power: L
Uncertainty: K
The noise for the operator may exceed 80 dB(A) and ear protection measures are
necessary.
=82.5dB(A)
pA
=93.5dB(A)
wA
& KWA=3.0dB(A)
PA
C to 40oC
17
Page 10
VIBRATION DATA
Hand arm vibration a
Uncertainty K=1.5m/s
The declared vibration total values and the declared noise emission values have
been measured in accordance with a standard test method(EN62841-1/EN62841-2-
14) and may be used for comparing one tool with another; they may also be used in a
preliminary assessment of exposure.
=1.2m/s²
h
2
SYMBOLS
01
ASSEMBLY
WARNING ! The vibration and noise emissions during
actual use of the power tool can differ from the declared
values depending on the ways in which the tool is used
especially what kind of workpiece is processed; and
need to identify safety measures to protect the operator
that are based on an estimation of exposure in the
actual conditions of use (taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the
trigger time).
RATING LABEL EXPLANATION
EHP18-Li = MODEL NUMBER E = ERBAUER
HP = HAND PLANER
18 = 18V d.c.
Li = LITHIUM ION
Read the instruction manual
Wear eye protection
Wear hearing protection.
Wear a dust mask.
Do not dispose of battery packs in rivers or immerse in water.
Do not dispose of battery packs in re. They will explode and
cause injury.
Do not expose battery packs to heat in excess of 40°C
Brushless motor
18
yyWxx
Keep Cool Battery Technology
Manufacturing date code: Year of manufacturing (20yy) and week
of manufacturing (Wxx)
19
Page 11
UNPACKING
02
DUST EXTRACTION (B1, B2, C)
Unpack all parts and lay them on a at, stable surface.
• Remove all packing materials and shipping devices, if applicable.
• Make sure the delivery contents are complete and free of any damage. If you nd that parts
are missing or show damage do not use the product but contact your dealer. Using an
incomplete or damaged product represents a hazard to people and property.
• Ensure that you have all the accessories and tools needed for assembly and operation. This
also includes suitable personal protective equipment
WARNING!
Children must not play with plastic bags, sheets and small parts! There is a
danger of choking and suffocation!
ASSEMBLING THE MACHINE
03
The product and the packaging are not children’s toys!
CHARGING YOUR BATTERY PACK
The battery has been shipped in a low charge condition. Charge it fully before rst use.
Refer to the charger instruction manual for the details.
TO REMOVE OR INSTALL THE BATTERY PACK (A1, A2)
Depress the battery pack release button to release and slide the battery pack out from
your tool. After recharge, slide it back into your tool. A simple push and slight pressure will
be sufcient.
BATTERY PACK POWER BAR
The Li-Ion battery pack (9) is equipped with a POWER BAR which is used to give an
indication of the battery pack’s remaining charge. Press the POWER BAR button (8) to
check battery charge as below. The LED will stay lit for approximately 5 seconds
.
76-100% Charge
WARNING!
this product in order to keep the working area clean! Wear a dust mask when
operating this product! Dust can be harmful to health! Especially dust of
wood that has been treated, e.g. with a wood preservative or stain!
Attach the dust bag or a dust extraction device when using
Selecting left / right dust extraction outlets
To select the dust extraction outlet (10) on the right hand side of the product move the
dust / chip extraction guide switch (3) to the left and attach the dust bag (20) or vacuum
cleaner to the dust extraction outlet on the right hand side of the machine. To select the
dust extraction outlet (10) on the left hand side of the product, do the opposite.
Dust bag
Carefully align the connector of the dust bag (20) to the dust extraction outlet (10) and
insert it all the way to the stop, turn the connector clockwise to lock the dust bag (20).
Pull the dust bag connector anticlockwise in a twisting motion to remove the dust bag (20)
Emptying
Open the zip and empty chippings into a suitable rubbish bag.
Close the zip and re-attach the dust bag (20) to the product.
Dust extraction
Alternatively a dust extraction system or suitable vacuum cleaner can be connected to
the dust extraction outlet (10) for a cleaner and safer work area.
PARALLEL GUIDE (D, E)
Attach the parallel guide (21) to the angle bracket (21a) as shown (D). Fix it with the
mounting screw, wing nut (21b) and washer.
Align the hole in the angle bracket (21a) to the mounting thread (11) and x them with the
wing screw (18).
Loosen the wing nut (21b) and adjust the parallel guide (21) to the desired width. Then
tighten the wing nut (21b).
8
Flash On Off
20
51-75% Charge
26-50% Charge
5-25% Charge
under 5% Charge
REBATE DEPTH GAUGE (F)
Attach the rebate depth gauge (19) and parallel guide (21) to perform rebate cuts.
Align the slot of the rebate depth gauge to the mounting thread and x it with a wing
screw. Adjust the rebate depth gauge to the desired depth then tighten the wing screw.
21
Page 12
USE
INTENDED USE
01
This product is intended for planing of rmly supported wooden materials, such as beams
and boards. It is also suitable for bevelling edges and cutting rebates.
OPERATION
02
ON/OFF SWITCH (G)
Press and hold the lock-off button (4) then press the on/off button (5) to switch the
product on. To switch the product off just release the on/off button.
Turn knob (2) Position front plate (13) Planing depth Blades (15)
Lowered to “P” position
(safety position)
<0 Fully retracted
to < 0
PLANNING (H, I, J)
NOTE:
especially after replacing or adjusting the planing depth.
Always make a trial cut before working on the actual workpiece,
NOTE:
The lock-off button can be operated from either side to allow left or
right handed use.
PLANING DEPTH
Adjust the desired planing depth by turning the cutting depth adjustment knob (2). The
depth can be adjusted between 0 and 2mm. The number next to the pointer indicates the
depth of cut in millimeters.
Turn knob (2) Position front plate (13) Planing depth Blades (15)
Retracted to maximum
position
1.5
2.0
0
P
Lowered to minimum position Decreased Fully retracted
P
0
1.5
1.0
0.5
Increased Fully lowered
for maximum
cut
for minimum
cut
Adjust the desired planing depth.
Hold the product with one hand on the handle (6), and with the other hand on the cutting
depth adjustment knob (2).
Switch the product on and wait until it runs at full speed before placing it on the
workpiece.
Place the front plate (13) at on the workpiece and push the product forward at an even
speed.
Turn the cutting depth adjustment knob (2) for depth adjustment anticlockwise to retract
the blades (15) after nishing your work.
BEVEL PLANING (K)
With the V-groove (12) bevel angles of 45° can be cut on the edge of a workpiece.
Place the V-groove (12) onto the edge of the workpiece. Guide the product along the
edge.
NOTE:
achieve an even result.
WARNING!
when switched on!
Apply slight consistent pressure against the parallel guide to
Danger of kickback! Apply the product to the workpiece only
22
23
Page 13
STANDARD SURFACE PLANING WITH OR WITHOUT THE PARALLEL
GUIDE (L, M)
Set the desired cutting depth. It is best to use small depths of cut and repeat the planing
process.
Attach the parallel guide (21) if required to the product as described above and adjust to
desired width.
Place the product laterally to the workpiece and guide the product along the edge.
NOTE:
and keep the base plate at on the surface to achieve an even result.
WARNING!
when switched on!
Apply light lateral supporting pressure against the parallel guide
Danger of kickback! Apply the product to the workpiece only
REBATE PLANING (N)
Attach the parallel guide (21) and rebate depth gauge (19) to the product as described
above and adjust to desired width and depth.
Place the product laterally against the workpiece.
Guide the product along the edge, repeat until the desired depth has been reached.
NOTE:
and keep the base plate at on the surface to achieve an even result.
WARNING!
when switched on!
Apply light lateral supporting pressure against the parallel guide
Danger of kickback! Apply the product to the workpiece only
OVERLOAD, TEMPERATURE AND CHARGING PROBLEM
Problem Tool/ Battery Status Possible cause Solution
Overload
protection
Temperature
extremely
high
Low charge Power for the tool will
Other
problems
Product suddenly
Stops; The LED
work light (if tted) is
ashing
The rst and the
third LED light of the
POWER BAR will be
ashing alternately
drop quickly; The rst
LED on the POWER
BAR begins to ash
Short charges Not fully charged Make sure that the battery
Extremely high
torque, binding and
stalling situations,
overloading of the
tool
Battery temperature
exceeds 77°C
during operation
The battery pack is
under 5% charge
Poor storage
condition
Relieve the load immediately,
reset the tool by switching
off and back on again.
Cool down the battery to
below 77°C for operation
and below 57°C for charging.
Remove the battery pack
from the tool and charge it
is fully charged every time
by allowing the charger to
complete its full charging
cycle
Always remove battery from
the tool and charger when
not in use and store in a dry
secure place. Avoid charging
or storing your battery in
temperatures below 5°C and
above 40°C. Cool down a
hot battery pack from a tool
that has just been operated
for approximately 30 minutes
before storage
24
25
Page 14
CARE & MAINTENANCE
CLEANING DUST EXTRACTION OUTLET
Free the dust extraction outlet (10) from blockages and dust using a suitable tool such as
a piece of wood or use high pressure air.
WARNING!
a nger or any other part of your body in the chip ejector opening. Always
clean a blocked chip ejector opening with a suitable tool such as a wooden
stick!
Never insert your bare ngers into the outlet! Never hold
Re-assembly (P)
NOTE:
replacement turn the blade vertically 180° and re-t it. If both sides of a blade
are worn out, replace with a new pair of blades.
Slide the blade between the blade xing element and cutter block (25). Be sure the
orientation of the blade is correct and it is positioned centrally.
Tighten the hex screws (23) clockwise until the blade is clamped tightly.
NOTE:
blades are set properly and securely. The blades must be mounted so that the
cutting edge is absolutely level, e.g. parallel to the surface of the back plate.
Usually planing blades can be used from two sides. For the rst
The planning surface will end up rough and uneven unless the
BLADES REPLACEMENT
WARNING!
damaged blades immediately! Dull and worn blades cannot be reground and
must be replaced. Observe the technical requirements of this product (see
section Technical specications) when purchasing and using replacement
blades! Blades are very sharp and become hot during use! Handle them
carefully! Wear protective gloves when handling blades in order to avoid
injuries like burns and cuts!
Always ensure to work with sharp blades. Replace worn or
Removal (O1, O2)
WARNING!
and new blades or blades of different types or brands!
Lay the product on a at surface so that you have free access to the bottom side.
Turn the roller (14) until the blade shaft is adjusted between the plates.
Loosen the hex screws (23) slightly anticlockwise using the wrench (22).
Push the blade (15) slightly with a piece of wood and then pull it out using a proper tool,
e.g. pliers .
Clean all parts carefully to clear dust.
WARNING!
pull out with bare hands!
Always replace both blades at the same time! Do not mix old
Always use a suitable tool to pull the blade out! Do not try to
The following examples show proper and improper settings:
a
a= Adjustable front plate (13), b= Fixed back plate (16)
Fig. I – Clean smooth cut.
Fig. II – Nicks in surface – as caused by the edge of one or all blades not being parallel
to the rear base line.
III
Fig.
– Gouging at start – as caused by the edge of one or all blades not protruding
enough in relation to the rear base line.
Fig. IV – Gouging at end – as caused by the edge of one or all blades protruding too far
in relation to the rear base line.
b
CUTTER BLOCK (Q)
The height is pre-set in the factory and normally there is no need to re-adjust.
Nevertheless check whether the front plate (13) runs parallel to the roller edge
occasionally. If necessary adjust the height with the hex key (26).
Loosen the hex screws (23).
Turn the grub screws (24) clockwise to increase the height.
Turn the grub screws anticlockwise to decrease the height.
MAINTENANCE
Your tool requires no additional lubrication or maintenance. There are no user serviceable
parts in your power tool. Never use water or chemical cleaners to clean your power tool.
Wipe clean with a dry cloth. Always store your power tool in a dry place. Keep the motor
ventilation slots clean. Keep all working controls free of dust.
a
b
a
b
26
27
Page 15
RECYCLING AND DISPOSAL
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or retailer
for recycling advice.
For further information visit www.recycle-more.co.uk
DISPOSAL OF AN EXHAUSTED BATTERY PACK
To preserve natural resources, please recycle or dispose of the battery pack
properly. This battery pack contains Li-Ion batteries. Consult your local waste
authority for information regarding available recycling and/or disposal options.
Discharge your battery pack by operating your tool, then remove the battery pack
from the tool housing and cover the battery pack connections with heavy-duty
adhesive tape to prevent short circuit and energy discharge. Do not attempt to
open or remove any of the components.
REPAIR
This product does not contain any parts that can be repaired by the consumer. Contact an
authorised service centre or a similarly qualied person to have it checked and repaired.
STORAGE
• Switch the product off and remove the battery pack.
• Clean the product as described above.
• Store the product and its accessories in a dark, dry, frost-free, well- ventilated place.
• Always store the product in a place that is inaccessible to children.
• We recommend using the original package for storage or covering the product with a
suitable cloth or enclosure to protect it against dust.
TRANSPORTATION
• Switch the product off and remove the battery pack.
• Attach transportation guards, if applicable.
• Always carry the product by its handle.
• Protect the product from any heavy impact or strong vibrations which may occur during
transportation in vehicles.
• Secure the product to prevent it from slipping or falling over.
GUARANTEE
At Erbauer we take special care to select high quality materials and use manufacturing
techniques that allow us to create ranges of products incorporating design and durability.
That’s why we offer a 2 year trade guarantee against manufacturing defects on our
Erbauer power tool products.
This power tool is guaranteed for 2 years from the date of purchase, if bought in store,
delivered or bought online. You may only make a claim under this guarantee upon
presentation of your sales receipt or purchase invoice. Please keep your proof of
purchase in a safe place.
This guarantee covers product failures and malfunctions provided the Erbauer power
tool was used for the purpose for which it is intended and subject to installation, cleaning,
care and maintenance in accordance with standard practice and with the information
contained above and in the user manual. This guarantee does not cover defects and
damage caused by or resulting from:
• Normal wear and tear, including accessory wear
• Overload, misuse or neglect
• Repairs attempted by anyone other than an authorised agent
• Cosmetic damage
• Damage caused by foreign objects, substances or accidents
• Accidental damage or modication
• Failure to follow manufacturer’s guidelines
• Loss of use of the goods
This guarantee is limited to parts recognised as defective. It does not, in any case, cover
ancillary costs (movement, labour) and direct and indirect damage.
If the Erbauer power tool is defective during the guarantee period, then we reserve
the right, at our discretion, to replace the item with a product of equivalent quality and
functionality or to provide a refund.
This guarantee only applies to the country of purchase or delivery and is not transferrable
to any other countries. This guarantee is non-transferrable to any other person or
product. Relevant local law will apply to this guarantee.
Guarantee related queries should be addressed to a store afliated with the distributor
you purchased the Erbauer power tool from.
This guarantee is in addition to and does not affect your statutory rights relating to faulty
goods as a consumer.
28
29
Page 16
DECLARATION OF CONFORMITY
EU Declaration of Conformity
Kingsher International Products Limited
Declare that the product:
Erbauer 18V cordless planer EHP18-Li
Serial number 00001-99999
Complies with the essential health and safety requirements of the following directives:
2006/42/EC The Machinery Directive
References to the following harmonized standard were made:
EN62841-2-14:2015
2014/30/EU Electromagnetic Compatibility directive
References to the following harmonized standard were made:
(EU) 2015/863 amending 2011/65/EU Restrictions of the Use of Certain Hazardous Substances in
Electrical and Electronic Equipment
Authorised signatory and technical le holder:
Kingsher International Products Limited
We
3 Sheldon Square
London W2 6PX
United Kingdom
EN62841-1:2015
EN 55014-1:2017
EN 55014-2:2015
3 Sheldon Square
London W2 6PX
United Kingdom
on: 18/06/2018
Lisa Davis
Group Quality Director
Page 17
Manufacturer • Fabricant • Producent • Hersteller • Producator • Fabricante:
Kingsher International Products Limited
3 Sheldon Square London W2 6PX
United Kingdom
www.kingsher.com/products
DISTRIBUTOR:
B&Q plc,
Chandlers Ford, Hants, SO53 3LE
United Kingdom
www.diy.com
Screwx Direct Limited,
Trade House, Mead Avenue,
Yeovil, BA22 8RT, United Kingdom
www.screwx.com
To view instruction manuals online,
visit www.kingsher.com/products
Loading...