Page 1
3000 Series
Digital Door Lock
Fitting Instructions
Mark and drill all six holes. Use a chisel to clear the line of 4mm x 8mm holes
into a single slot..
Mark central point on the ‘centre line of the latch’ on the door edge
Drill a 25mm hole at an 85mm depth.
Insert the latch into the hole, and draw around the face plate.
Remove the latch and cut a 3mm rebate so that the face plate will fit flush with
the door.
Secure the latch with the wood screws.
Tape the template to the door making sure you fold it along the appropriate line.
A
- Pliers (with cutting facility)
- Pencil
- Drill
- 8mm and 25mm drill bit
To fit a Digital Door Lock you will require the following tools:
- Crosshead screwdriver
- Wood chisel
- Ruler / tape measure
- Mallet
Special Notes (for 3001 and 3003 only):
The ‘Hold-open’ model is equipped with a snib on the backplate. This enables
the latchbolt to be held open when required.
Before commencing installation, check that all parts are working correctly.
Also refer to code change instructions.
Make sure that the lever handle of the backplate moves freely. Check that the
snib will engage, and hold the handle in the ‘latch-open’ position, if it is a model
with the latch stopper.
Check that the latch bolt moves freely by pressing at the end and also by turning
the flat spindle in the latch cam.
ERA, Straight Road, Willenhall, West Midlands. WV12 5RA
Tel: +44 1922 490049 Fax: +44 1922 494420 Email: info@erahomesecurity.com
Positioning and fixing the latch
Apply the Template
Installing a 3000 Series Digital Door Lock
www.erahomesecurity.com
B
Page 2
Position the strike plate on the door so that it lines up with the flat of the latchbolt (NOT THE PLUNGER).
Mark the inner and outer edges of the strike plate and cut a 1mm rebate so that it fits flush with the
surface or the door frame.
Drill or cut a recess for the latch bolt.
Fit the strike plate using only one wood screw at first to
ensure that it is positioned accurately. The latchbolt, and
not the plunger should enter the aperture easily and be
held without too much ‘play’. When satisfied, secure the
strike with the second screw.
G
Fixing the Strike Plate
ERA, Straight Road, Willenhall, West Midlands. WV12 5RA
Tel: +44 1922 490049 Fax: +44 1922 494420 Email: info@erahomesecurity.com
www.erahomesecurity.com
Cut the fixing bolts to suit the door thickness, allowing at least one
threaded section to screw into the lockcase.
Hold the lock case and backplate (with the seals onto the door)with
the spindle in position.
Using the fixing bolts screw everything together through the top
and bottom holes of the backplate. Before final tightening, make
sure the lock is vertical, and test the mechanism to ensure that all
is moving easily.
Caution: Do not close the door until you are sure that the code works.
Do not over tighten the fixing bolts as this may cause distortion and lead to poor operation..
F
Fixing the Lock
Select the spindle to suit the thickness of the door.
Insert the spindle through the slot in the door and make
sure that it engages the latch correctly for the hand of
the door (see inset diagram).
E
Positioning the Spindle
When fitting a backplate to a left-handed door
the BLUE screw must go in the right-handed hole
and vice versa.
D
Blue Handing Screw
C
Latch Support
Fit the latch
support post in
hole A for a right
hand hung door.
or B for a left
hand hung
A
B
veiwed from
the outside
Door hung on the right
spindle should engage
the latch as above
Door hung on the left
spindle should engage
the latch as above
N.B. THE PLUNGER BESIDE THE LATCHBOLT DEADLOCKS
THE LATCHBOLT AND PROTECTS IT AGAINST
MANIPULATION. IT MUST NOT ENTER THE STRIKE
PLATE APERTURE WHEN THE DOOR IS CLOSED
Plunger
Latchbolt
Page 3
Fold along the edge of the door
(match to length of LATCH)
Fold along the edge of the door
(match to length of LATCH)
60mm60mm
Centre line
of latch
Centre line
of latch
8mm hole
130mm
8mm hole
Outline
of rubber
seal
Outline of
Lockcase
Drill 4 x 8mm holes
and a clear slot
through the door
TEMPLATES
8mm hole
130mm
8mm hole
Outline
of rubber
seal
Outline of
Lockcase
Drill 4 x 8mm holes
and a clear slot
through the door
Loading...