EPYC ION 600, ION 800, NEON Series, NEON 850VA, NEON 650VA User Manual

IMPORTANT SAFETY INSTRUCTIONS
INTRODUCTION

Standby UPS with APFC support

User Manual

600/800

Before to start using the UPS please read carefully this manual, so to ensure the best usage and the maximum life

duration of the machine.

The main features of this Uninterruptible Power Supply (UPS) are listed below:

 Microprocessor control that guarantees high reliability

 APFC (Active Power Factor Correction) loads support

 DC start function

 Auto restart during AC recovery

 Modem and phoneline surge protection

 Built-in USB communication port

This manual contains important safety instructions. Please read and follow all instructions carefully during installation

and operation of the unit. Read this manual thoroughly before attempting to unpack, install, or operate your UPS.

CAUTION! To prevent the risk of fire or electric shock, install in a tem perature and humidity controlled indoor area free

of conductive contaminants. (See the specifications for the acceptable temperature and humidity range.)

CAUTION! To reduce the risk of overheating the UPS, do not cover the UPS cooling vents and avoid exposing the unit

to direct sunlight or installing the unit near heat emitting appliances such as space heaters or furnaces.

CAUTION! Do not attach non-computer-related items, such as medical equipment, life-support equipment, microwave

ovens, or vacuum cleaners to UPS.

CAUTION! Do not plug laser printers, scanners or aquariums into the UPS outlets because of their high start-up current.

CAUTION! The UPS must be connected to a grounded AC power outlet with fuse or circuit braker protection. DO NOT

plug the UPS into an outlet that is not grounded.

CAUTION! Do not allow liquids or any foreign object to enter the UPS. Do not place beverages or any other liquid-

containing vessels on or near the unit.

CAUTION! Do not plug the UPS input into its own output.

CAUTION! Do not attach a power strip or surge suppressor with >1,5m wire to the UPS.

CAUTION! With the installation of the UPS, it should be prevented that the sum of (UPS and) the connected (load)

leakage current exceeds 3.5mA

CAUTION! In the event of an emergency, press the OFF button and disconnect the power cord from the AC power

supply to properly disable the UPS.

CAUTION! The socket-outlet shall be installed near the equipment and easily accessible.

CAUTION! Internal battery voltage is 12V DC. Sealed, lead-acid, 6 cells battery

CAUTION! A battery can present a risk of electrical shock and high short circuit current. The following precautions

should be observed when working on batteries:

1) Remove watches, rings, or other metal objects from the hands.

2) Use tools with insulated handles.

3) Wear rubber gloves and boots.

4) Do not lay tools or metal parts on top of batteries.

5) Disconnect charging source prior to connecting or disconnecting battery terminal.

CAUTION! Servicing of batteries should be performed by personnel knowledgeable of batteries and the required

precautions. Keep unauthorized personnel away from batteries.

CAUTION! When replacing batteries, replace with the same number of the sealed lead-acid batteries.

POSITIONING

INSTALLING YOUR UPS SYSTEM
BASIC FUNCTIONALITIES

CAUTION! Unplug the UPS prior to cleaning and do not use liquid or spray detergent.

CAUTION! This UPS utilizes voltages that may be hazardous. Do not attempt to disassemble the unit. The unit contains

no user replaceable parts. Only authorized service personnel may perform repairs.

CAUTION! Do not stick fingers into sockets.

Please follow the instructions to correctly position your UPS:

1. The UPS must be placed on a horizontal surface.

2. This UPS is projected for indoor use.

3. The UPS must not be exposed to direct sunlight or any heat source.

4. The air temperature must be between 0°C and 40° C (25°C is the ideal temperature).

5. Ambient humidity must be less than 90%.

6. The UPS must not be placed on dusty environments.

7. The UPS must be placed at least 15 cm. far from walls to ensure enough ventilation.

8. Do not obstruct or pour any liquid on ventilation holes.

9. Do not cover the UPS with any object.

10. Keep away liquids, flammable gases or corrosive substances.

INSTALLING YOUR UPS SYSTEM

UNPACKING

The box should contain the following: UPS Unit x1, USB cable x1.

HARDWARE INSTALLATION GUIDE

1. The UPS may be used immediately upon receipt. However, recharging battery for at least 8 hours is recommended

to ensure that the battery's max charge capacity is achieved. Charge loss may occur during shipping or storage. To

recharge the battery, simply leave the unit plugged into an AC outl et: it will charge in both the on and off position.

2. With the UPS unit off and unplugged, connect the computer, monitor, and any externally powered data storage

device (Zip drive, Jazz drive, Tape drive, etc.) into the battery power supplied outlets. DO NOT plug a laser printer,

copier, space heater, vacuum, paper shredder or other large electrical device into the battery power supplied outlets.

The power demands of these devices will overload and possibly damage the unit.

3. Plug the UPS into a 2 pole, 3 wire grounded receptacl e (wall outlet). Make sure the wall branch outlet is protected

by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g. air conditioner,

refrigerator, copier, etc). Avoid using extension cords.

4. Press the power switch to turn the unit on. The power on indicator light will illuminate and the unit will "beep".

5. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this, turn the

UPS off and unplug at least one piece of equipment from the battery power supplied outlets. Wait 10 seconds. Make

sure the circuit breaker is depressed and then turn the UPS on.

6. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

7. To store your UPS for an extended period, cover it and store with the battery fully charged. Recharge the battery

every three months to ensure battery life.

600/800 VA

1. Power Switch

Press the switch to turn the UPS ON or OFF.

2. Led Indicators

Three LED indicators include Using AC, Using Battery, and Fault. Refer to “Definitions for Illuminated LED Indicators”
section for details.

3. AC Outlet

The UPS provides 3 outlets for connected equipment to insure tem porary uninterrupted operation during a power
failure and against surges and spikes.

4. Input Circuit Breaker

The Circuit Breaker provides overload protection.

5. RJ45/11 Communication Protection Ports

Provide surge protection for any standard modem, fax, telephone line, or network cable

6. USB COMM. Port

This port allows connection to the USB port on the computer, so to get access to remote monitoring and shutdown
operations through the UPS management software

7. Input Power Cord

Connect to utility power.